Question about Chevrolet Lumina

Open Question

Chevrolet lumina 2000 code P0410 secundary air injection system

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: my 2005 chevy trail blazer has code p0410 and i

check the air pump on your trailblazer, make sure its clean inside and the hoses are properly fastened. also check to make sure it works properly by listening for it when you start the vehicle. if the air pump is working correctly, replace the position 1 o2 sensor meaning the sensor on the exhaust manifold. the air pump is located under the vehicle, inside the frame rail on the drivers side in front of the transfer case crossmember with 2 hoses connected to it.

Posted on Feb 21, 2009

Ad
Molson02536
  • 3854 Answers

SOURCE: engine code p0410

If the air pump is working then it's going to be the one way check valve at the manifold. It's common for the check valves to go bad before the air pump, check the pipe from the pipe to the manifold too.
Before you get that far i believe there was a TSB and the warranty is 5 years to the emission system on vehicles. Looks like your close to the end of your 5 year so step on it to the dealer while you can still get a deal on this repair.
Good luck and hope this helps.

Posted on May 27, 2009

  • 52 Answers

SOURCE: 2001 chevy tahoe dianostic codes p1416 and p0410

http://img245.imageshack.us/img245/39/218488404lv.jpg
http://img241.imageshack.us/img241/4642/443329838do.jpg

And some instructions

Removal Procedure

Caution: Allow the engine to cool before servicing the secondary air injection AIR system in order to reduce the chance of severe burns.
1. Remove the clamp from the check valve.
2. Disconnect the AIR hose from the check valve.
3. Remove the check valve from the left side AIR pipe.
4. Remove the left AIR pipe from the exhaust manifold.
5. Before replacing a check valve, test the valve for proper operation.
5.1. Install a vacuum pump to the nipple side of the check valve, AIR pump side.

5.2. Pump the vacuum pump to 10 inches Hg and observe the gauge.

5.3. Replace the check valve if the vacuum bleeds down to zero within 5 seconds.


Installation Procedure

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

1.Install the check valve onto the AIR pipe.
Tighten the check valve to the AIR pipe to 23 N·m (17 lb ft).
2.Connect the AIR pipe to the exhaust manifold.
Tighten the AIR pipe to the exhaust manifold to 20 N·m (15 lb ft).
3. Install the AIR hose to the check valve.
4. Install the check valve clamp.

Posted on Jul 08, 2009

  • 184 Answers

SOURCE: P0410 Secondary air injection system fault, P0128 Coolant temp

most ecu controlled vehicles have a 'limp home'mode if 2 or more fault codes are stored,it is designed to get your attention before damage is caused and to get you to the nearest w.shop to fix,i would have codes cleared and retest vehicle,it is the cheapest and 1st option for any shop,some late models even have excessive mileage past service interval in the 'limp' program

Posted on Jul 24, 2009

  • 118 Answers

SOURCE: 2002 pontiac montana van ''service engine soon'' light

Diagnostic Aids

  • Low system airflow can cause an intermittent complaint. Inspect for the following conditions:
    • Any restriction in the exhaust system that may produce back pressure
    • Pinched, kinked, restricted, or leaking pipes, hoses, or fittings
    • A restricted pump inlet hose, duct, or filter
    • Pinched, kinked, restricted, or leaking vacuum lines
    • Heat damage
  • A short to voltage in the pump relay control circuit can result in the AIR pump running continuously with the ignition OFF by back-feeding to ground. This will eventually result in pump failure.
  • An AIR pump that had become inoperative and had shown indications of having exhaust gases in the outlet port would indicate check valve failure.
  • Notice Do not operate the AIR pump for more than 60 seconds. Continuous operation of the AIR pump in excess of 60 seconds will damage the AIR pump.

    If the DTC cannot be duplicated and is determined to be intermittent, reviewing the Failure Records data can be useful in determining when the DTC was last set. Also refer to Intermittent Conditions

Posted on Oct 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Air injection pump where is it located on the motor


were is the secondary air injection air pump located on a 1996 monte carlo z34 with the 3.4liter
\

Aug 31, 2012 | 2000 Chevrolet Venture

1 Answer

P0410 code 01 02


P0410 - Secondary Air Injection System Malfunction
Possible causes- Faulty Vacuum hoses damaged
- Faulty Air Pump inoperative
- Air bypass solenoid harness is open or shorted
- Air bypass solenoid circuit poor electrical connection
- Air bypass solenoid leaking/blocked or stuck open/closed
- Air diverter valve leaking/blocked or stuck open/closed

Read more: http://engine-codes.com/p0410.html#ixzz24VOZPAy2

Aug 24, 2012 | 2000 Chevrolet S-10

1 Answer

Po410Secondary Air Injection System Malfunction


Common Problems That Trigger the P0410 Code
  • Defective Air Pump Check Valve(s)
  • Faulty Air Pump or Air Pump Relay
  • Faulty air control solenoids or vacuum lines
  • System may be restricted or plugged with carbon If you do not hear the Air Pump Motor start, then check the SAS Air Pump and relay. If you hear the motor, inspect the components that control the Air delivery such as the Check Valve Solenoid, the Check Valve and the rubber hoses, metal piping and passages. good-day !

Mar 19, 2012 | 2000 Chevrolet Lumina

1 Answer

I have a 1999 chevy malibu its 6 cylinders 3100 engine and i have the codes with me this aare the codes that i need 1.#p0420 2.#p0410 3.#p0305 4.#p0449


P0420 - Catalyst System Low Efficiency
P0410 - Secondary Air Injection (AIR) System
P0305 - Cylinder 5 Misfire Detected
P0449 - Evaporative Emission (EVAP) Vent Solenoid Control Circuit

Sep 05, 2011 | 1999 Chevrolet Malibu

2 Answers

What does this code mean? P0410


Diagnostic Test Code (DTC) P0410 indicates that your secondary air injection system is not functioning properly.
Not all 2001 Chevrolet Bazers are equipped with secondary air injection. The secondary air injection system was added to vehicles that were to be sold in certain areas where the emissions laws required it, like the State Of California.

The Powertrain Control Module (PCM) monitors the system by commanding the secondary air blower motor to run and the air injection solenoid to open. This causes additional oxygen to enter the exhaust system. The PCM then monitors the signal from the oxygen sensors to see if the commanded air has in fact, entered the exhaust system. Code P0410 sets when the PCM has commanded the blower motor on and the solenoid open and there is little or no change in the oxygen sensor signal.

GM has had some problems with these systems and there has been a Technical Service Bulletin (TSB) issued that addresses some of the known concers. Below is a brief description of the TSB and the issues involved.

Bulletin No.: 04-06-04-015A
Date: November 28, 2006
TECHNICAL
Subject:
LN2, L43 or L35 Engine SES/MIL Light Illuminated, AIR Pump Ingesting Water and DTC P0410 Set (Replace AIR Pump and Inlet Hose Assembly)
Models:
1999-2003 Chevrolet Blazer, S10
1999-2001 GMC Jimmy
1999-2003 GMC Sonoma
1999-2001 Oldsmobile Bravada
with Vortec 2.2L I4 or 4.3L V6 Engine (VINs 4, 5, W - RPOs LN2, L43, L35)
Condition
Some customers may comment on the SES/MIL light being illuminated. Upon investigation, the technician may find a DTC P0410 indicating that there is a concern in the secondary air injection system.
Cause
Water may have collected in the AIR pump or the vent solenoid and frozen or corroded the pump.
Correction
Replace the AIR pump and install a new inlet hose and solenoid tube assembly...

The bulletin goes on and gives detailed information on how to perform the repair and the part numbers of the replacement parts needed to do so. Your local dealer can provide the parts for you and you can probably get them to print out a complete copy of the bulletin for you. It is not really hard to do if you want to do this yourself.

Sep 01, 2011 | 2001 Chevrolet Blazer

2 Answers

Check engine light on, diagnostic code 0128 and 0410 keep coming up


P0128 - Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)

P0410 - Secondary Air Injection System Malfunction
(has to do with exhaust system)

Note: There is a technical service bulletin (TSB) regarding code P0410 for a number of GM models. The TSB calls for the replacement of the AIR pump and the installation of a new secondary injection hose.

Oct 13, 2009 | 2005 Chevrolet TrailBlazer

2 Answers

Checked why engine light was on and it gave code P0410 Secondary injection system. to me this is very vague. can you help?


that code indicates a problem w/ the air injection system, a part of the emissions system. you should check the air pump, solenoid, check valves and vacuum hoses of that system. the emissions sticker under the hood should give you a detailed enough diagram of where the components are

Sep 30, 2009 | 2001 Chevrolet Blazer

1 Answer

2000 blazer codep0410????


this code is caused by a failure of the motor in the electric secondary air injection pump of the emission system.

Jun 19, 2009 | 2000 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...