Question about 2002 Chevrolet TrailBlazer

1 Answer

Rear axle bearing replacment

Do you have to remove the rear diff cover to access a clip/lock to release axle shaft so it can be pulled and bearing replaced on end of shaft?

Posted by on

  • Anonymous Mar 26, 2014

    how to remove the rear end spider in gear in one peace?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,674 Answers

Not 100% sure on that vehicle & don't have manual on it at this time, but will say very common that it does have "C" like clip at end of axle. Large pin comes out first, then push axle in slightly & remove clip, & slide axle out.

Posted on Feb 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

HOW DO I CHANGE THE REAR WHEEL BEARINGS IN A 1993 JEEP GRAND CHEROKEE LARADO?


no they are bad, unless its brakes
a real mech , checks both.
its one or the other, or worse. bad axle gear/bearings/

the fsm covers both. ever seen the real book? on this car.
the ZJ book is here and free

http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service
posted like 100+ times, now......

keep in mind jeeps may have different axles.
2wd, 4wd, and locking axles (options)
models 30, 35 and 44 so the details vary that is why the book wins here. the real book wins.

diagnosis is an other matter, i have an electronic stethoscope
that allows me to drive and hear each bearing. cost me $35.

id inspect brakes first. after all they are in clear easy view.
make sure the brake parts are not seized. that includes
the Emg. brake parts !!!
does you car have ABS brakes?
some have drums others have rear disc brakes, the linked FSM
covers both.

for example disc calipers can fail in many ways
guides seized.
pistion seized
emg brake part stuck.
cracked rotors, or warped.

so that be first a real brake inspection on side that makes noise.

if the brakes are ok, then axle bearings are checked next
if you feel radial play they are BAD.
and more. ask.

May 01, 2015 | Jeep Grand Cherokee Cars & Trucks

2 Answers

How do i remove my rear axles on my 1977 dodge aspen


Top of Form 1
Raise the vehicle and remove the rear wheels.
Clean all dirt from the housing cover and remove the housing cover to drain the lubricant.
Remove the brake drum.
Rotate the differential case until the differential pinion shaft lockscrew can be removed. Remove the lockscrew and pinion shaft.
Push the axle shafts toward the center of the vehicle and remove the C-locks from the grooves on the axle shafts.
Pull the axle shafts from the housing, being careful not to damage the bearing which remains in the housing.
Inspect the axle shaft bearings and replace any doubtful parts. Whenever the axle shaft is replaced, the bearings should also be replaced.
Remove the axle shaft seal from the bore in the housing, using the button end of the axle shaft.
Remove the axle shaft bearing from the housing. Do not reuse the bearing or the seal.
Check the bearing shoulder in the axle housing for imperfections. These should be corrected with a file or polish.

Apr 24, 2011 | Dodge Diplomat Cars & Trucks

1 Answer

Removing rear axle seals for a 1986 S-15 Jimmy


Pull the rear wheels,take off the diff cover,remove the 5/16 pin that holds the big pin,pull the big pin ,push in on the axles,remove the 2 c clips that are on the axles and slide the axles out.If the axle shaft is worn by the bearing,an axle -saver bearing is available. If the axle is ok just pull the seal ,drive the new one in and re-assemble.

Apr 10, 2011 | GMC S-15 Cars & Trucks

3 Answers

How to replace rear Axle seal on 4x4 chevy


this is very hard if you do not know what you are doing. Ill try to step you through this
  • pull wheels
  • drain pun-kin case
  • pull rear cover
  • in between the spider and axle sets pull C ring with needle nose pliers
  • pull hub and axle out CAREFULLY as there are roller bearings on the end of the axle housing
  • pull seal out at the end of axle housing
  • tap in new seal CAREFULLY and straight DO NOT BEND IT or it will be junk
  • replace axle carefully as the roller bearings are still there
  • replace C clip to original position
  • replace axle diff cover and replace the gasket with a new one
  • refill diff case
  • install tire
  • your good to go

May 03, 2010 | 2002 Chevrolet Silverado

1 Answer

Rear axle bearings


when u say axles are u referring to the shafts,if so remove the diff plate and therte are two c-clips holding them in

Mar 08, 2010 | 2003 Chevrolet Silverado 2500HD

1 Answer

2002 dodge 1500 rear end making whining nosie


This could be one of several problems: If the noise increases with speed, and you are only hearing it from the rear differential and not the transmission, it could be the rear differential carrier bearings, or rear axle bearings going bad. If you are only hearing the noise upon acceleration or deceleration, the rear differential ring and/or pinion gears may be going bad and the rear differential will need an overhaul. You'll have to get the rear wheels off the ground and see if you can pinpoint the location of the noise with something such as a stethoscope. If it's coming from the rear differential, you'll need to pull the bolts and the cover to determine if the gears are still in good shape, or if there is any pitting. Same with the carrier bearings; if you see pitting/ discoloration, they'll need replacement. If the noise is coming from one side towards the end of the axle shaft near the wheel, it's most likely a axle bearing going bad, and you'll need to pull the wheels, remove the diff. cover to release the C clip which holds the rear axle in place at the differential, and pull the axle out. You also need a special tool with a slide hammer to remove the axle bearing and seal.

Nov 20, 2009 | Dodge Ram 1500 Cars & Trucks

2 Answers

Rear end


Did you pull the pin at differential just to be sure? If it's non-"C" clips, you'll need a slidehammer attached to hub, over studs & use wheel nuts to hold it on there. Get er done !

Apr 24, 2009 | Chevrolet Monte Carlo Cars & Trucks

2 Answers

Rear wheel bearing


SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
  1. Remove the differential pinion shaft (4211).
    1. Remove the differential pinion shaft lock bolt (4241).
    1. Remove the differential pinion shaft.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Remove the U-washer (4N237).
    1. Push the axle shafts (4234) inboard.
    1. Remove the U-washer.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
    Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Remove the axle shaft.
--------------------------------------------------------------------------------------
Rear Wheel Bearing and Axle Shaft Oil Seal Removal
  1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.
  1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.
Installation
  1. Lubricate the new rear wheel bearing with the specified lubricant.
  1. Using the special tools, install the new rear wheel bearing.
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the new wheel bearing oil seal.
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

-------------------------------------------------------------------
Installation
  1. Lubricate the lip of the wheel bearing oil seal
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Install the two axle shafts.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Install the U-washer.
    1. Position the two U-washers on the button end of the axle shaft.
    1. Pull the axle shaft outward.
  1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
    Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the case lock bolt hole.
    1. Install a new differential pinion shaft lock bolt.
  1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
  1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. Install the rear brakes. For additional information, refer to Section 206-04 .
  1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.

Apr 10, 2009 | 2004 Ford GT

2 Answers

Rear bearing


rear axle bearings I assume? Pull the diff cover, rotate the carrier so you can remove the pin from the center of the 4 spyder gears, push the axle in slightly, and remove large c clip from the carrier area. The axle will pull right out! These vehicles are hard on axle bearings. Look them all over.

Good Luck!

Apr 02, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Getting rear gears out of the difential case 1999 dodge durango


  1. Raise and support vehicle. Ensure that the transmission is in neutral.
  2. Remove wheel and tire assembly.
  3. Remove brake drum. Refer toBrakes, for proper procedure.
  4. Clean all foreign material from housing cover area.
  5. Loosen housing cover bolts. Drain lubricant from the housing and axle shaft tubes. Remove housing cover.
  6. Rotate differential case so that pinion mate gear shaft lock screw is accessible. Remove lock screw and pinion mate gear shaft from differential case
  7. Push axle shaft inward and remove axle shaft C - clip lock from the axle shaft
  8. Remove axle shaft. Use care to prevent damage to axle shaft bearing and seal, which will remain in axle shaft tube.
  9. Inspect axle shaft seal for leakage or damage.
  10. Inspect roller bearing contact surface on axle shaft for signs of brinelling, galling and pitting. If any of these conditions exist, the axle shaft and/or bearing and seal must be replaced

Feb 07, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
2002 Chevrolet TrailBlazer Logo

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...