Question about 2008 GMC Acadia

Open Question

How to change the blend door actuator on 2008 acadia

The heat inside car will blow cold until car starts to move...temperature on guage will go up and down...temp goes up it will blow cold and as soon as it starts to go down it blows heat

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2920 Answers

SOURCE: 2004 GMC Sierra Heater does not heat on low RPM

check your coolant level on the radiator

Posted on Feb 03, 2009

honeymokey
  • 3113 Answers

SOURCE: air blend door

Replace the broken actuator.

Posted on Apr 15, 2009

  • 436 Answers

SOURCE: How do you fix the driver side air blend door actuator?

you cannot repair the actuator you need to replace it with new one. These motors turn but get weak with time. if you test it, it works, put it in and it doesn't. this is because the motor is weak, unfortunately GM does not sell these motors separately.

Posted on Aug 23, 2009

  • 1 Answer

SOURCE: Air conditioner blows hot air after 30 seconds on

I have had this problem. I am not a mechanic...so to correct the issue temporarily, I simply turn off the car and restart. This has worked everytime for me. In extreme cases, I think you can also remove the AC fuse and start the car, which will also reset the computer. I also think that by taking the climate control off the "AUTO" setting has worked in the past.

Posted on Oct 27, 2009

JJ_Barricade
  • 11 Answers

SOURCE: 1995 GMC suburban temp guage pegs high, but heater

Sounds like there may be an air pocket in the system.
Try 'burping' the system. If this still doesn't fix the problem, check the temperature of the heater core hoses (in and out) The inlet should be fairly cool, the other should be piping hot. If they're both cold; the heater core has an internal blockage.

Next, replace the thermostat with a winter (180-195 F) derivative.
Bleed the system accordingly, and keep me posted!

Posted on Nov 30, 2009

Testimonial: "Thanks. Very useful information, provided very quickly."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The heater kicks on but only blows cold air


Air Temperature Control Blend Door Failure No Heat or no AC (dependes on where door sticks)

In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car. Always have this problem confirmed by a dealer or qualified repair shop as it is a very expensive repair.

Other causes of no heat in the cabin are engine thermostats that are stuck open (engine runs cold) or air bubbles in the cooling system.

Jan 03, 2013 | Cars & Trucks

2 Answers

Heater blows only cold air


Air Temperature Control Blend Door Failure No Heat or no AC (dependes on where door sticks)

In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car. Always have this problem confirmed by a dealer or qualified repair shop as it is a very expensive repair.

Other causes of no heat in the cabin are engine thermostats that are stuck open (engine runs cold) or air bubbles in the cooling system.

Dec 27, 2012 | 1999 GMC Sierra

2 Answers

Heater doesn't get hot on 96 chevy truck. Blows good, just cold. Replaced thermostat, flushed radiator. Any ideas?


Air Temperature Control Blend Door Failure No Heat or no AC (dependes on where door sticks)

In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car. Always have this problem confirmed by a dealer or qualified repair shop as it is a very expensive repair.

Other causes of no heat in the cabin are engine thermostats that are stuck open (engine runs cold) or air bubbles in the cooling system.

Dec 06, 2012 | Cars & Trucks

1 Answer

2008 ford rangerhave vacuum but no heat


Air Temperature Control Blend Door Failure No Heat or no AC (dependes on where door sticks)

In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car. Always have this problem confirmed by a dealer or qualified repair shop as it is a very expensive repair.

Other causes of no heat in the cabin are engine thermostats that are stuck open (engine runs cold) or air bubbles in the cooling system.

Nov 09, 2012 | 1996 Ford Ranger SuperCab

1 Answer

I mitsubishi RKX502A001C that I cant get to blow hot and is only blowing cold air?


Air Temperature Control Blend Door Failure No Heat or no AC (dependes on where door sticks)

In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car. Always have this problem confirmed by a dealer or qualified repair shop as it is a very expensive repair.

Other causes of no heat in the cabin are engine thermostats that are stuck open (engine runs cold) or air bubbles in the cooling system.

Nov 05, 2012 | Cars & Trucks

1 Answer

Heater blows cold air


Air Temperature Control Blend Door Failure No Heat

In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car. Always have this problem confirmed by a dealer or qualified repair shop as it is a very expensive repair.

Nov 01, 2012 | Pontiac Cars & Trucks

1 Answer

No heat blows cold air


In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car.

Oct 24, 2012 | 2004 Mitsubishi Lancer

2 Answers

Heater blows cold air


Hi!
If the Temp. Selector Control is set to Heat and blows cold air, your Blend Door Actuator may be stuck or it is inoperative. The actuator is not fixable, if it fails, it must be replaced. Follow the instructions to remove and replace it.
  1. Disconnect battery negative cable from battery and properly isolate to prevent accidental reconnection.
  2. Remove the instrument panel.
  3. Disconnect the electrical connector from the blend door motor/actuator.
  4. Remove the four screws holding the blend door actuator to the plenum.
  5. Remove the temperature blend door actuator.
BLEND DOOR ACTUATOR CONNECTOR e8349ea.jpg

BLEND DOOR FASTENING SCREWS 9744710.jpg

Show your appreciation with a - 4 THUMBS - rating for answering your FREE question. Thank you for using FixYa.

Oct 07, 2010 | 2003 Mercury Grand Marquis

2 Answers

No front heat


where is the heat blend door located 97 ford e-350 van

Jan 29, 2009 | 1997 Ford Econoline

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...