Question about 2004 Chevrolet Suburban

Open Question

WHERE IS THE TEMP SENSOR LOCATED ON 2004 CHEVY SUBURBAN

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 373 Answers

SOURCE: 1998 chevy suburban map sensor

Hi, The Map sensor on a Suburban is located.
Beside of the ignition coil. on the intake.
Is a litle sensor with a connector of 3 wires.

I hope this work for you. OK

Posted on Jul 03, 2008

Ad
ginko
  • 19396 Answers

SOURCE: AC Low Pressure location on 2004 Chevy Suburban

You find the AC low pressure at the top of the compressor, orientated toward you , facing the front of the vehicle. You can also follow the compressor line to reach the port.

The valve is covered a plastic cap covering it.
Near the compressor you find two ports, the high port and low port.

To find out which one is the low port, run the air conditioner for a couple of minutes withthe engine on.
Then turn off the care and touch the lines from compressor to the two ports covered with plastic caps. Only one of the pipes will be cold, the cold line will lead you to the low port.

Regards.

Posted on Jun 18, 2009

  • 634 Answers

SOURCE: coolant fan temp sensor location on a 2003 chevy venture

located in thermostat housing or in intake nearby (where top hose connects from radiator to engine)

Posted on Jul 16, 2009

localwonder
  • 6784 Answers

SOURCE: knock sensor location

HI, click the link below to be directed to a full diagram that will show you the actual location of the sensor. 718 will be the actual sensor to extract and 739 is the mounting screw for the KS.

KNOCK SENSOR DIAGRAM

Posted on Jul 22, 2009

  • 212 Answers

SOURCE: where is knock sensor located on 2004 chevy 2500Hd

Under intake manifold on top of block,you need to remove intake to access sensors there are two of them you can't miss them when intake is off. After replacing sensors you need a new intake gasket.

Posted on Apr 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the knock sensor for 04 chevy suburban located


There are 2 of them and they are located in the valley pan under the intake manifold.

May 26, 2012 | 2004 Chevrolet Suburban

1 Answer

How to change a speed sensor on 2004 chevy surban


That depends on WHICH speed sensor you want to change. The Vehicle speed sensor? a front wheel speed sensor? A rear wheel speed sensor? an input shaft or turbine speed sensor?

Jul 23, 2011 | 2004 Chevrolet Suburban

2 Answers

Where is the tps sensor located on a 1994 6.5 chevy diesel suburban?


Its runs 90 degrees off the the parallel shaft that cortrols the throttle plate on the left side of the air horn

Nov 24, 2010 | 1998 Chevrolet Suburban

1 Answer

2004 Chevy suburban fuel filture location?


Inside frame, drivers side on the fuel line.

Jul 20, 2010 | 2004 Chevrolet Suburban

1 Answer

Where is the location of the bank one sensor one o2 sensor on my 2003 chevy suburban


bank 1 on a chevy is on the drivers side youll have 4 O2 sensors sensor 1 bank 1 is on the engine side of the cat converter sensor 2 bank 1 is after the cat converter (drivers side )
bank 2 is on the passenger side sensor 1 is pre cat sensor 2 is post cat converter

Mar 18, 2010 | 2003 Chevrolet Suburban 1500

1 Answer

Chevy Suburban 1997 1500 won't start when Cold


it could be a tune up issue such as plug wires plugs . but my guess is its a computer engine temp sensor if it reads 5 degrees out of range it cuold give you a hard start or a no start problems the best way to look at this problem is with a scan tool when it is cold to see if the temp matches outside ambeint air temp 1 or 2 degrees ok b ut not 4 to five there is a nother way to check it buy useing dvom at a temp to omhs chart.

Jan 11, 2010 | 1997 Chevrolet Suburban

1 Answer

Changing CO2 Sensor on 2003 Chevy Suburban


check the whole exaust sestyem? there should be 4to5

Mar 19, 2009 | 2003 Chevrolet Suburban

1 Answer

CHEVY SUBURBAN FAILED SMOG BECAUSE OF HIGH NOX VALUES.


nox is from running lean..... its realy high temps that cause this.......... replace the o2 sensors this should cure that any more help let me know

Oct 24, 2008 | 1993 Chevrolet Suburban

1 Answer

Temp Sensor


The temp sensor known as the engine coolant temp. sensor tells the computer if the engine is overheating and so forth and tells the injectors how much fuel to give the engine. The temp. sending unit is what controls what your guage reads. It sounds like you need the temp. sending unit. It located near the thermostat housing with a single pole connector.

Jun 18, 2008 | 2004 Chevrolet Impala

Not finding what you are looking for?
2004 Chevrolet Suburban Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...