Question about Cars & Trucks

Open Question

What are the torque specs for the flywheel bolts on a 98 honda passport 3.2 liter

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Torque spec for flywheel bolt: Isuzu 2.5 diesel engine

normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

Posted on Aug 15, 2008

  • 218 Answers

SOURCE: I need some torque specs for the connecting rod

20 FT LBS + A 1/4 TURN

Posted on May 04, 2009

joecoolvette
  • 5660 Answers

SOURCE: Bolt torque specs for flywheel, pressure plate,

1.Flywheel - 61 to 69 Foot Pounds
2.Pressure Plate - 25 to 33 Foot Pounds
3.Bell Housing - No specs found. I would say 25 to 35 foot pounds should be sufficient.

Bolts clean on ->flywheel to crank, ->pressure plate to flywheel, and ->bell housing to back of engine, I would use TWO drops of Loctite Red threadlocker, on ALL of these bolts.

Hope you have an alignment tool for your clutch disk when you install it. Auto parts stores sell the plastic one's cheap! Saves a LOT of headaches!

Tighten the pressure plate EVENLY! Snug the bolts down until they just TOUCH, then go in a criss-cross pattern when tightening. Do the tightening in incremental stages! You turn one bolt one thread, you go across to the opposite side, and turn that bolt one thread. Keep criss-crossing so the pressure plate goes down EVENLY. (YES, it's a pain in the keister!)

If NOT, you'll have a warped pressure plate, and it will be junk!
Thanks for letting me say that, I feel better.

Posted on Jul 07, 2009

c17hydro
  • 2984 Answers

SOURCE: torque spec 96 ford contour 2.0 liter dohc head bolts

Please don't forget to rate!

1st step 15-22 ft.lbs.
2nd step 30-37 ft. lbs.
3rd step Tighten the bolts an additional 90-120 degrees

Do you need the tightening sequence?

Posted on Oct 18, 2009

  • 12 Answers

SOURCE: head bolt torque specs for 200 honda accord 3.0

its a three step process 1st 29ft/lbs 2nd 51ft/lbs 3rd 72.3ft/lbs

Posted on Apr 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 ford windstar intake manifold torque specs


Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

Flywheel torque spec's for 1983 Ford F-100


Could it be a F-150 instead?
Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP's, you should follow the recommended torque specifications.

260, 289, 302 Torque Spec.
Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Connecting rod bolts (40-45 ft-lbs. for 289 HP & Boss 302) Cylinder head bolts 65-72 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351W Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 90-100 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs. Oil pump bolts 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351C, 351M Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) Cylinder head bolts 105 ft-lbs. (125 ft-lbs. For Boss 351C) Rocker arms (non-adjustable) Rocker arms (non-adjustable) 5/16in. intake manifold bolts 21-25 ft-lbs. 3/8in. intake manifold bolts 28-23 ft-lbs Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 9-12 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs. 360, 390, 406, 427, 428FE Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Crossbolts for 406-427 40 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) Cylinder head bolts 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427) Rocker arm shaft bolts 40-45 ft-lbs. Intake manifold bolts 32-35 ft-lbs. Oil pump bolt 12-15 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 429-460 Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 140 ft-lbs. Rocker arms (non-adjustable) 18-22 ft-lbs. Intake manifold bolts 25-30 ft-lbs. Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs.

Dec 18, 2015 | Ford Cars & Trucks

1 Answer

Torque spec's for the fly wheel


Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP's, you should follow the recommended torque specifications.

260, 289, 302 Torque Spec.
Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Connecting rod bolts (40-45 ft-lbs. for 289 HP & Boss 302) Cylinder head bolts 65-72 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351W Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 90-100 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs. Oil pump bolts 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351C, 351M Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) Cylinder head bolts 105 ft-lbs. (125 ft-lbs. For Boss 351C) Rocker arms (non-adjustable) Rocker arms (non-adjustable) 5/16in. intake manifold bolts 21-25 ft-lbs. 3/8in. intake manifold bolts 28-23 ft-lbs Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 9-12 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs. 360, 390, 406, 427, 428FE Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Crossbolts for 406-427 40 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) Cylinder head bolts 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427) Rocker arm shaft bolts 40-45 ft-lbs. Intake manifold bolts 32-35 ft-lbs. Oil pump bolt 12-15 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 429-460 Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 140 ft-lbs. Rocker arms (non-adjustable) 18-22 ft-lbs. Intake manifold bolts 25-30 ft-lbs. Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs.

Dec 18, 2015 | Cars & Trucks

1 Answer

Hi im in need of torque specs for 94 honda passport flywhhel and and exedy pressure plate its the 4x4 3.2 l v6 thanks


About 60 pounds on the flywheel and 30 pounds on the pressure plate. Use locktite thread locker on all the bolts.

Aug 22, 2015 | Honda Cars & Trucks

1 Answer

Torque specs for crank shaft pulley bolt on 1997 honda accord 2.2


the torque specs for the crankshaft pulley bolt on the 2.2 liter engine is 181 foot pounds

f3da1049-5f03-4476-b18a-1b251097af2d.png

Apr 25, 2015 | 1997 Honda Accord

1 Answer

What is the head bolt torque specs for a 1998 honda passport 3.2l


you will need that and the sequenced and if the old bolts are TTY
torque to yield. and don't mix left. and right gaskets.
(the correct question?)


1- Step 1: 21 ft. lbs. Step 2: 47 ft. lbs. STAGED !


use alldata.com
below is the bolt sequence order. no tty mentioned. but????
6137
front---------------rear
5248

Feb 11, 2014 | 1998 Honda Passport

1 Answer

I need the torque specs for a 1999 honda cr-v flywheel


according to autodata the torque settigs for the flywheel bolts are 103nm pal

let me know if this helps

cheers
mike

Jul 03, 2012 | 1999 Honda CR-V

1 Answer

Torque on front ball joints 2000 Honda Passport 2 wheel drive


Lower ball joint specs:
Torque the ball joint-to-control arm nuts/bolts to 85 ft. lbs. (115 Nm). Torque the castellated nut to 108 ft. lbs. (147 Nm).

Upper ball joint specs:
Tighten the mounting bolts to 42 ft. lbs. (57 Nm) and the castellated nut to 72 ft. lbs. (96 Nm).

Feb 28, 2011 | 2000 Honda Passport

2 Answers

Torque settings for 2005 lancer es fly wheel gearbox etc


2.0L Evolution engine

flywheel bolts 132 =/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.0L Non- Evolution engine

flywheel bolts 98 +/-5 N.m. 72 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.4L Ralliart engine

flywheel bolts 132 +/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

Dec 28, 2010 | 2005 Mitsubishi Lancer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...