Question about Hyundai Motor 1995 Accent

Open Question

1982 suzuki gsx 250 will start but it wont idle so i gave the carbie a clean and blew all the jets with compressed air to no avail. Also will run for around couple of minutes before it comes to a slow death (will lose power until it stalls). sometimes there is smoke from around the engine. There is an oil leak from under the engine somewhere. Does anyone know is this the oil strainer being clogged or restricted or have another idea. thanks for your help

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My suzuki quad runner cranks & idles but when you give it gas-spits and sputters/YOU MASH THE STARTER BUTTON asgiving it gas/runs fine.(starter stays engaged whole time)


no
there is nothing wrong with the starter but if you keep doing what you report the stater motor will burn out
the problem is in the carburetor main jet circuit or fuel blockage to the carby
you report that it starts and idles so the electrics if fine but on acceleration it plays up which indicates that the air/fuel mixture is getting too lean
now it is time to overhaul the carby, check float level, check fuel flow from the tank( taps corrode internally and block flow)
being a quad bike it could have water in the fuel system or dirt in the filter

Jan 13, 2017 | Suzuki Cars & Trucks

1 Answer

What is the correct float height on 1998 yamaha 650 v star carburetors . 12mm or 14mm ???????


it will start and run on either float level but will not carry load or high rpms
your statement that it requires a choke ( blocking air intake) to start indicates a assembly problem in the carby/s
blocked main jets, idle circuits
it could also be a fuel supply problem to the carb/s
(filter , lines, taps) it could be possible that the float action is wrong and the float is in a down position and blocking off the needle and seat as if the bowl is full
the float setting will be available on the net
go google and enter-- float setting/adjustment for yamaha 1998 v star motor cycle ---
look also for a workshop manual for the carby/s make on line to check assembly correctness

Nov 17, 2016 | Yamaha Cars & Trucks

2 Answers

1983 st90 f8a, suzuki carry van. it will start. but when i apply accelerator it will cut out. like it is starving fuel. i get fuel to the carb, but thats where im stuck.


A carburettor has an eccelerator pump which gives a small squirt of fuel into the venturi when depressing the gas pedal. it consists of either a diaphram or a small rubber cup (as in a car tyre pump) if this is worn or faulty it is most likely the cause of the problem and has to be replaced. This is normally included in a carburettor kit which can be purchased at most auto parts dealers. I suggest you get one and replace all the parts supplied in the kit. I am 90% certain this will solve your problem

Oct 29, 2015 | Suzuki Cars & Trucks

1 Answer

Suzuki lt50 manual


have you tried starting with the air intake pipe/hose removed from the carb ? if still wont start i'd strip carb down and clean out the jets , not forgetting the idle jet at bottom of bowl , also check the diaphram pump is in working order , rubber diaphram still flexable not holed etckeep me posted if you wish

May 26, 2014 | Cars & Trucks

1 Answer

My 1984 gmc with a carborated 350 starts runs and idles fine but bogs at half throttle wont rev up will drive at nearly an idle but any sort of gas it bogs and almost dies i used carb cleaner yet it still...


it could be a fuel blockage or it could be that the main running jets in the carby are blocked you may have to remove the carby & strip it down & blow it out with compressed air, but check for a fuel blockage first........hope this helps......cheers.

Jul 19, 2011 | 1984 GMC C1500

1 Answer

I have a 1988 carburetor that has a cloged idle jet and I need to unclog it How do I do it? What is the best way to do that?


unscrew the idle mixture screw,count the turns,blow down hole with compressed air,rescrew screw back in.if it works,ok.if it doesnt work,youll have to strip carbie and clean it inside,jets,galleries,everything thoroughly.may need new gasket set.lay it all out carefully,on large sheet of newspaper,.if two barrel,dont get jets mixed up from one barrel to the other..have clean container of petrol to rinse and wash each part.use fine wire to clean any jets/air bleed holes etc..blow dry bits away from work place..use widest screwdriver blade that will fit,saves damaging jets[in fact,buy a new set of screwdrivers]

Jun 20, 2010 | Cars & Trucks

1 Answer

My 89 b2200 cranks fine and runs as long as my foots on the gas it wont idle itself...ive put another choke thermostat on it but it still does the same thing???


Need to check carby for corect idle / mixture settings. Might have a blocked jet.

If you can remove the idle jet, blow compressed air into the hole, screw back in till it just bottoms out then unscrew 2 full turns to get started.

Mar 30, 2010 | 1988 Mazda B2200

1 Answer

1989 toyota camry 232000miles Runs rough at idle


YOUR problem is the carby acc pump and idle jet ...... what you need to do is remove airfilter and take the top off the carby and you should see a small ball and spring under gasket ...when you open the throttle it will pump petrol to the small pick up jet and the other jet will take over ...clean out carby jets and rebuild and that should be ok

Sep 23, 2009 | 1989 Toyota Camry

1 Answer

I have an 1982 f 250 4.9 and go through carburaters a lot. New ones last may be a year then start burnning way to much gas. The carb has an idle adjustment and a curb idle adjustment no air gas mixture...


1982 ?? their wouldnt be any adjustment as they are fixed jet carbs ,you could try fitting new jets but whats causing them to eat away in the first place i dont know unless its the fuel additive that you have to add to the unleaded fuel

Jul 12, 2009 | 1982 Ford F 250

Not finding what you are looking for?
Hyundai Motor 1995 Accent Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

78238 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...