Question about 1992 Dodge Ram 250

1 Answer

Transmission mount how do u change a transmission mount on a 1992 dodge ram 250 two wheel drive 5 speed

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 296 Answers

Its bout the same for all rear wheel. Place a jack to support the transmission, remove the bolts from the mount and frame. If the tranny on a cross member then you should be able to remove the cross member by 4 bolts, then remove the mount from tranny and cross member.

Posted on Jan 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the oil pressure sensor on a 1992 dodge cummins?


It's mounted in the engine block under the injection pump on the driver side of the engine. It's right up against the power steering pump, above a motor mount.

Mar 17, 2013 | 1992 Dodge Ram 250

1 Answer

Need to know what 5 speed transmissions will interchange with a 92 ranger with a 3.0


You didn't mention if it was 2 or 4 wheel drive so I went with a 2 wheel drive. According to hollander the 5 speed transmaaion fits a ranger (2WD) 1991 - 1994 and a Mazda B3000 1994 only. Hope this helps.....

Oct 29, 2012 | 1992 Ford Ranger

1 Answer

1992 dodge ram 150 fuel filter location


I replaced fuel filter 1992 Dodge Ram W150 4wd 5.2 engine...located inside frame rail psgr side just fwd of rear wheel. mounted 1/2 in. bolt.

Jun 14, 2012 | 1992 Dodge Ram 150 Club Cab

1 Answer

Ignition, will not start, no spark att all... The camshaft provider tested its ok, seems to be no electricity going To the provider...


    Types
  1. The 1993 Dodge transmissions could be found in the Caravan, Colt, Dakota, Daytona, Dynast, Intrepid, Ran Van, Ram Wagon, Ram Charger, Shadow, Spirit, Stealth, Viper and W150. Each had a unique array of transmissions best suited for the model's design.
  2. In 1993, the Dodge transmissions varied between 3- and 6-speeds. A 3-speed automatic transmission was available, and there was a variant that included overdrive. The only other automatic transmission included 4-speeds. A 5-speed manual gearbox found its way into several of the 1993 Dodge models, and a 6-speed manual was equipped in the Viper.
  3. The number of speeds and style of transmission may have looked the same on paper, but it did not mean they were all the same. An automatic transmission in a passenger sedan could be geared drastically different from one in a truck. Transmissions may have the same number of speeds, but they may not be geared identically.
  4. Transmissions were used in the 1993 Dodge to effectively transfer power from the engine to the wheels of the vehicle. The power could be passed to the front or rear wheels. Models equipped with all- and four-wheel-drive had power at all four-wheels.

Jan 08, 2011 | 1993 Audi 100

1 Answer

The speedometer stops working and it goes out of overdrive. It doesn't matter what speed I am going it happens intermitantly. Sometimes it will happen and go back to normal right away and sometimes it will...


You need to have the transmission serviced. Make sure you tell them this problem. It is a solenoid problem in the transmission that will need replaced.

Oct 09, 2009 | 1992 Dodge Ram 250

1 Answer

The brakes on my 1992 dodge ram 250 4wd will only brake when you press them down real hard, they are quite stiff, do you know what might be wrong and the solution for it?


Thats the brake booster.Its located behind the master cylinder on top of the fire wall.In the engine compartment on other side of steering wheel

Jul 12, 2009 | 1992 Dodge Ram 250

2 Answers

Speedometer not working -check engine light ON- ABS light ON


Check the RWAL censor on the rear axle, had the same problem

Jan 06, 2009 | 1999 Dodge Ram

1 Answer

4 Wheel Drive Does Not Engage


transfer case or front diff to check put transfer case into 4x4 go under the truck and move the front drive shaft it should go in if working. Hope this helps.

Dec 01, 2008 | 1992 Dodge Ram 250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...