Question about Cars & Trucks

Open Question

Why does my john deere 5525 blow a fuse every time i turn the switch on?

I dont even try to crank it.I only turn the key one click,(to acc) and it blowes the fuse every time.I have taken all the fuse's out but the switch fuse and it still blows it.I have replaced the switch.And did not help.

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 58 Answers

SOURCE: ECM BATT fuse keeps blowing

That fuse provides power for the fuel pump. Either your fuel pump is blowing the fuse or there is a shorted wire.

Posted on Dec 21, 2008

  • 6982 Answers

SOURCE: ignition switch fuse terminal is blowing red 40 amp fuse when i try to replace it

A fuse that is consistently blowing is telling you that there is a short in that system. Don't attempt to bridge it or use a larger amp fuse or you will have a major problem. You will need to start tracing wiring to destinations to find the short. If while moving harnesses around problem ceases to exist, look at nearby items where you are working and try to locate what was grounding. Sometimes people will stop if short disappears, leaving open the possibility of it happening again.
If you are not comfortable working with wiring, then leave it to professionals who do this every day. It's not really difficult but requires patience and a good bit of knowledge to do this right!

Posted on Apr 18, 2009

  • 1 Answer

SOURCE: gauges blow fuses,brake and turn signal lights dont work

all my gauges quit working and my turnsignals checked all my fuses under the hood and dash whats my problem?

Posted on Mar 03, 2010

  • 86 Answers

SOURCE: when key is turned to on position, keeps blowing 30 amp fuse

It sounds like you have a short in some wiresets. Check the wires directly connected to the ignition. If this persists, without any problems with wires, I suggest checking the amperage and voltage on your battery to make sure they are at operational levels. Anything over 14.8 volts and you start to fry electrical components and... blow fuses.

Posted on Mar 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my john deere la145 mower blow a fuse every time I turn the key


will need a meter to check wiring and battery for short

Jul 05, 2017 | Cars & Trucks

1 Answer

My Johb Deere 4310 won't start. No sound when I turn the key on the ignition switch. Battery's good, fuses are good. Indicator lamp 1 long and 6 short. What's wrong?


John deer is a seek and find mission. A good electrician could possibly find and fix it. But the would be breaking the law. Some how, John Deer got federal laws passed, That no one can work on the computer systems in their tractors. Unless you are a dealer.. You might try looking up code 16 for John deer.

Jul 28, 2016 | Cars & Trucks

1 Answer

Place key in ign. And turns with no clicks btw off acc and start. When you turn off, goes past off to acc no clicks


Hello Ron, If your car does not crank when you turn the key, it sounds as if you have problems with the ignition switch . Or the actuating rod is disconnected.

Apr 10, 2015 | 1998 Buick Park Avenue

1 Answer

My ignition fuse is a 40 amp when I check the voltage it is drawing 51.0 amps why


Since most of the circuits are handled by the key switch, you'll have to disconnect a few fuses and relays to find the overload.

Feb 06, 2013 | 1993 Dodge Dakota

1 Answer

My GMC safari 2004 has been blowing Ignition 1 fuse (40 amps) at the moment I turn key to start position,even without starter disconnected it blowed but i replaced the fuse and i removed the starter r


The problem could be a shorted park netual safety switch . Do you know what a wiring diagram is ? It shows all the componets involved in a electrical circuit ! You IGN.1 fuse 40amp , GM calls it IGN A fuse 40 amp . It feeds the ignition switch and pin 30 at the starter enable relay .When you turn the key to the start position it sends B+ voltage to #8 crank fuse , located in the I/P fuse box ,from there it goes to the park netual safety switch , to pin 86 or 85 of the starter enable relay ! If you pull the relay out of the fuse box an look on the bottom you will see this four set's of numbers ,30,87 & 85 ,86 You can test at the fuse box where the relay plugs in . Here is a video on how to test . The guy presenting the video uses a horn circuit , but it works the same way . It happens a lot , the park netual safety switch shorting out . It may or may not be the problem . VEHICLE RELAYS Operation Diagnosis
Here is a web site for free wiring diagrams
http://www.bbbind.com/free_tsb.html Enter your vehicle info . then under system click on engine , then under subsystem click on starting . Then click on the search button an a link will pop up , click on it .You will see all the componets , connections , wiring colors etc... for the starter circuit for your vehicle .

Apr 17, 2017 | 2004 GMC Safari

2 Answers

Every time I turn the key to start the motor it blows the 30 amp fuse what is the cause and how do I fix it


if the fuse is blowing when you turn key to start position then this is where to look for the fault ,between the ignition switch and the relay then the other side of the relay to the starter motor solonoid

Mar 05, 2011 | Ford Focus Cars & Trucks

1 Answer

30 amp ignition fuse in engine compartment blows at start


It sounds like a bad ignition switch or something is grounding out.Try to isolate the problem to key positions.See if the fuse blows when you turn the key to ACC(when your dash lights come on without starting)If the fuse does not blow then when you go to start it and it blows it could be one of many problems,the more common ones could be ignition switch,wiring,starter relay,starter soleniod,or perhaps the starter itself is shorting out,this can sometimes happen when a starter goes bad.

Apr 12, 2009 | 1996 Hyundai Accent

2 Answers

My 1997 honda accord wont start.....


Hi Matt

Follow the( + ) positive lead from the battery, to the starter, check the connections, if all OK, get someone to turn the ignition key to start, and give the starter a tap, on the selenoid, with a small hammer or a metal socket extension.

Good Luck !

Let me know the outcome !

Also a FixYa rating would be nice !

John

Feb 10, 2009 | 1997 Honda Accord

1 Answer

Main Fuel Pump


Fuses mean short somewhere.Fuse is always live it feeds relay but in tank pump [ fuse#4or#6 i forget anyway visa versa ] is not live until this.Relay clicks once when key tuned to on and once more when key turned to crank engine it is under dash by glove box and loud enough for someone with ear at this spot to hear.In tank pump should not be live until engine starts to crank.

Aug 03, 2008 | 1984 Volvo 240 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

578 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...