Question about Chrysler PT Cruiser

Open Question

How to remove windshield washer nozzle pt cruiser

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

rockitman187
  • 2559 Answers

SOURCE: 2004 chrysler pt cruiser starter motor removal

You may sneak it out with small fingers with out pulling out the starter.

If starter removal is required,Just unhook the battery cables,Remove the 2 bolts holding the starter on.


Please rate this a fixya

Posted on Feb 08, 2009

cadman000
  • 607 Answers

SOURCE: windshield washer does not work. nothing comes out

Possibilities include a faulty washer pump / fuse , or a clog in water flow between washer fluid tank and nozzles.along with everything in between

Posted on Mar 24, 2009

  • 91 Answers

SOURCE: windshield wipers on pt cruiser

the pump wire is probably not making good connection with the pump that is why the washer fluid wont work try and clean the connection. the pump is located under the fill tank

check for a bad relay for the wipers not working. the relay will be under the hood or under the dash next to the fuses. the cover will tell you what piece is the relay. the relay controls the delay in the wipers so that is probably bad and you can get them at napa for cheap. and simple to install its just like a fuse.

Posted on Mar 28, 2009

  • 101 Answers

SOURCE: my headlights,windshield wipers, and turn signals wont work

check all your fuses. replace any and all bad ones. if fuse blows again u have a short somewher

Posted on Jul 03, 2009

  • 6982 Answers

SOURCE: Fix washer nozzle

Unless it's already broken, try putting a fine piece of wire (like one strand of a multi strand wire) into the nozzle tip to clear it out, then blow some compressed air through it. Every nozzle is attached differently and I don't know even what car you have but one waring that applies to all, is do not take it off when very cold or the plastic will snap.

Posted on Jan 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Windshield washer hums, resavior is full, no fluid spray. New nozzles. See no leaks. Bad motor?


most of them are located on the bottom of the tank mounted outside of the tank, with a little labor you should be able to do it, it will have 2 hoses and one plug ,you may have to remove a plastic guard protecting it, first see if you can buy one some aftermarket ones are cheaper than buying from dealer

Feb 25, 2015 | 2008 Chrysler Pt Cruiser

1 Answer

2001 pt cruiser i hear the motor of the windshield washer but is not working what can i do and where is the fuse


I would check your lines and your nozzles on the sprayers They could be blocked The lines could be blocked also

Nov 10, 2011 | 2001 Chrysler PT Cruiser

2 Answers

I have a 2004 PT Cruiser. Windshield washer reservoir is full but will not spray onto windshield.


the pump which is located on the outlet of the reservoir is either defective, corroded/loose electrical wiring on it or a blown fuse. Check the fuse first seeing it the easiest. Hope this helps

Jan 19, 2011 | 2005 Chrysler PT Cruiser

2 Answers

Window washer does not work on my 2001 pt cruiser i can hear the motor when i push the fluid button


If you hear the motor run, the nozzles may be clogged, see if you can clean them or blow air through them. Take the hose off under the hood to the nozzles and see if it pumps out there.

Dec 14, 2009 | 2001 Chrysler PT Cruiser

1 Answer

2004 PT Cruiser: Windshield water spray is very


CHECK THE SUPPLY TUBES FROM THE PUMP TO THE SPRAY HEADS. SOME TIMES FINE PARTICALS OF DIRT WILL STOP THESE UP REMOVE THE HOSE FROM UNDER THE HOOD AND USE COMPRESSED AIR AND BLOW FROM THE SPRAY HEADS BACK TO THE OPEN HOSE TO CLEAN OUT THE DIRT IF THIS DOSN'T WORK LEAVE THE HOSE OFF AND TRY THE WASHER WITH OUT THEM HOOKED UP SEE WHAT KIND OF FLOW YOU GET FROM THE PUMP IF IT IS VERY LOW THE PUMP IS BAD

Aug 25, 2009 | 2001 Chrysler PT Cruiser

1 Answer

2005 pt cruiser


EITHER MOTOR SEIZED OR SYSTEM IS CLIGGED

Jan 06, 2009 | 2005 Chrysler PT Cruiser

2 Answers

Washer fluid and a sticky unlock on back door


check the fuse for the washer pump first.

Jul 04, 2008 | 2006 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

344 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...