Question about 1998 Chevrolet Malibu

1 Answer

I.ve got a sreaming from one of my pullys and would like to know if they can be lubricated

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Any auto parts stores have a product called belt dressing. just lube her up comes in a spray and dosn't stink

Posted on Jan 05, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sprayed my tensioner pully with a lubercant about 15miles of driving after my van started looseing acceleration while the rpm stayed the same as if I was still going 60did I possibly ruin a censor


Don't spray any pulleys or the serpentine belt with any spray lubricant as you will just cause the belt to pick up lubricant and slip on all the pulleys it is running on.
Whatever lubricant is left on the surfaces you sprayed clean it off.

No you will not have damaged a sensor.

Nov 10, 2015 | Cars & Trucks

1 Answer

Tensioner pully needs to be replaced


that bearing in the pully is good for freezin up. wen it does the belt brakes from overheating.. i've done 3 over 5 year time. releeve tension on pully and remove belt. remove tthe 1 bolt in middle of pulley.then go in reverse.spray w/good lubricant.

Jan 25, 2013 | 1999 Ford Crown Victoria

1 Answer

2004 Toyota 4Runner Dual Control Heat cold Passenger side


The fuse your looking for is under the hood in front of the driver

Oct 12, 2012 | 2004 Toyota 4Runner

1 Answer

I have a 2001 2500 chevy duramax. At 2100 plus RPMs the headlites flicker off and on and the AMP gauge goes to the negative. I have replaced the tension pully, both idler pullys and the belt. I brougt it...


A little movement is normal,
a lot of movement can cause fuses to blow, or burn up things like computer, radio, and backup camera. It should 've no more than 14.5 volts. Also look tension on pulley to loose can give same results.

Oct 07, 2017 | 2001 Chevrolet Silverado 2500HD

1 Answer

I have a 1997 pontiac grand prix gtp and on the supercharger nose cone pully its making a really loud squealing noise and doesnt go away and it gets louder the faster it goes. I spray like a lubricant like...


THE FRONT BEARING IN THE SUPERCAHRGER HAS GONE BAD. DO NOT DRIVE IT TIL' IT IS FIXED.
YOU WILL GET STRANDED AND MAYBE RUIN THE ENGINE IF PARTS GET SUCKED IN THE INTAKE.
ROBERT

Nov 01, 2010 | Pontiac Grand Prix Cars & Trucks

1 Answer

What is pully below a/c compressor


what car/truck? Serpentine belt vehicles have an IDLER pulley which may become squeeky when the bearing looses its lubrication. Ford used their alternator bearing on many applications, but you would have to have it pressed out and a new one in. The complete pulley and bearing can be purchased.

Oct 20, 2010 | Ford F-350 Cars & Trucks

1 Answer

Trying to find procedures for a 2001 bmw z3 3.0 water pump replacement


to start you will need a 32 mm wrench and long narrow flathead to remove the fan blade,looking at the motor is releases the the right,spin off the blade and remove along with fan shroud for accesabilty,loosten the 4 10mm nuts on the water pump pully before removing the belt as bekt will hold tension but dont fully remove the bolts just release a couple of turnsuse a 16mm socket or a 8mm hex key to remove the alternator w/p belt,no need to remove fully,there will be either a hex head for a socket on the belt tensioner and if not pop off the plastic cover on the front of the pully to reveal a hex key bolt, once the belt is off remove the 4 w/p pully bolts, if the pully doesnt come right off lubricate with penetrating oil and tap lightly with a hammer while spinning it slowly and it will release,now that the pully is removed you can now see 4 10mm nuts hold on the w/p.remove the nuts and spray aroung the pump with wd40,you can try to pull and wiggle on the pump, if it doesnt come out you must obtain 2 bolts that will fit to the sides of the pump, you will see two thread holes that are empty,when you thread a bolt through with even tension on l and r sides the w/p will begin to pull away from the block. Once the pump is out lubricate the new pumps o ring with coolant to help slide it in, push in the new pump and re assemble in reverse,to fill the cooling system open the phillips screw on the overflow expansion tank,fill system with a 50=50 mixture of coolant until coolant comes through the bleeder screw with no bullbles,close the blleder screw and run the car at idle with the windsheild defroster on and heat at full. monitor the coolant level until it has sufficient flow and close cap,you can have a friend rev the engine to about 2000 rpm for this, road test the car and allow to cool, re check for leaks and fluid level when cold again to ensure repairs are correct

Mar 31, 2010 | 2001 BMW Z3

2 Answers

On a 2000 plymonth voyager wy does serpintine belt come off when it rains


Because the belt is not tracking straight and water lubricates and helps it skip over the groves.Make sure belt is aligned properly and is inline on all pullys

Nov 20, 2009 | 2000 Plymouth Voyager

1 Answer

Pulley broke off motor i need to know what the pulley is called to be able to order it


i need to know what part of the motor the pully came off. a ideler pully is smooth the other pully have grove

Mar 22, 2009 | Infiniti I35 Cars & Trucks

1 Answer

One of my pullys have stopped moving and causing the car to make a weird noise


what pulley? water pump most likely. Could be alternator. More info needed. Apply spray penetrant/lubricant like WD-40.

Dec 24, 2008 | 1992 Oldsmobile 88

Not finding what you are looking for?
1998 Chevrolet Malibu Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...