Question about 1999 Lexus RX 300

Open Question

1999 lexus rx300 mode servo - 1999 Lexus RX 300

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
keithheavili
  • 410 Answers

SOURCE: ? to Replace Timing belt on 2000 Lexus Rx300 with 57,000 miles.

If it is running perfectly I wouldn't think that you would need to replace the timing belt. You shouldn't need to replace that until 100,000-120,000 miles. I would definitely hold off until now unless you have start having some timing problems. Let me know if you have any other questions. Thanks for rating my response and for using FixYa!

Posted on Jul 08, 2009

Ad
  • 17 Answers

SOURCE: replace side marker light on lexus rx300

Remove 3 - 4 screws on fender cover close to side marker light. Pull fender cover out a bit for you to use your other hand to reach side marker light. By twisting on one direction and here you go the light out. Replace new bulb and replace everything on reverse order.

Posted on Aug 18, 2009

Murphybanton
  • 2004 Answers

SOURCE: Lexus RX300 engine light n VSC light comes on

VSC means Vehicle Stability Control.

It comes on when the sensor send a signal that the vehicle is not stable on the ground.....check the wheel balancing and alignment and the air pressure of your tires too.

Good luck.

Rate this solution.

Posted on Aug 23, 2009

  • 71 Answers

SOURCE: I have 3 codes 1) P0500

The PO125 is an indication of an engine running too cold-as if the thermostat were stuck open.For some reason it often sets with the PO1135 even when the engine runs at normal temp.A scan tool will indicate exactly how hot the engine is,don't trust the dash gauge. The PO1135 is a heater circuit fault in the bank1 sensor1 air fuel ratio sensor or oxygen sensor. Bank 1 is the REAR bank on this car...that O2 sensor is not much fun.PO500 is a vehicle speed sensor fault-does the speedo work correctly?it is located in the transmission near the back of the case. once again the scan tool will read vehicle speed and can aid in further diagnosis.

Posted on Mar 30, 2010

  • 120 Answers

SOURCE: 1999 lexus rx300 check engine

Your 306 code means you have a misfire on cylender 6. That may be the cause of the po 125. Inspecdt the coil, spark plug wire, and spark plug on cylender 6. With the age of the car I would replace all 3 items. If you want know how to test all 3 I can tell you process of elimination is the way to do it. Do you know how to find cylender 6

Posted on Oct 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Lexus Rx300 shift stick moving up and down but not shifting.


According to the parts book, it uses a $300 shift cable assembly. Have you tried shifting the transmission arm with the cable disconnected ?

Feb 19, 2014 | Lexus RX 300 Cars & Trucks

1 Answer

I have a Lexus RX300 1999 model and have this recent problem. engine running normally but gear gets stuck in Parking mode and won't shift. had to depress the emergency button on the gear shift and


Hi there,

Some automatic vehicles rely on the brake switch (mounted on brake pedal) to be activated by depressing brake pedal. This signal then operates a relay and switch, to release the gear lever.

Firstly, I would check the brake pedal switch (are your brake lights working?).

If brake switch is confirmed OK, then inspect the relay (and related circuit components) of the gear release switch.

Mar 04, 2013 | 1999 Lexus RX 300

2 Answers

1999 lexus rx300. fan won't blow. ac light is on


Possibly the connector to the blower unit has been diconnected or is loose.

Apr 13, 2010 | 1999 Lexus RX 300

1 Answer

Lexus rx300 2002 hard shift between 1st and 2nd. Fluid and filter changed 3000mi ago, car has 93000mi


The 1999-2003 Lexus RX300 models have a common failure of the engine computer that causes the harsh shifting of the transmission. You need to get the computer (ECM - Engine Control Module) rebuilt or replaced before it causes permanent damage to the transmission. Even if the transmission is already ruined, the ECM will still need to be repaired. Most often, the transmission is fine though, and rebuilding the ECM will restore the smooth shifts that the Lexus should have. Circuit Board Medics can rebuild the ECM and reprogram it so that you only have to plug it back in when you get it back. See the link below:

http://circuitboardmedics.com/1999-2003-lexus-rx300-hard-transmission-shifting-ecm-ecu-computer-repair/

Jan 25, 2010 | 2002 Lexus RX 300

1 Answer

99 lexus rx300 has engine miss on cyl 2,4,6 all


2-4-6 could be a fuel or ignition issue, hopefully not a valve. If you have the engine tested at the dealership they will attach a code reader under dash to analize and this should help pinpoint the problem.

Jan 07, 2010 | 1999 Lexus RX 300

1 Answer

Lexus rx300 started running without a key.. keys


Check your starter solenoid or your ignition switch, sounds like there is a short causing the car to start when the weather changes

Dec 31, 2009 | 1999 Lexus RX 300

1 Answer

Lexus rx300 cabin filter assembly


It is not necessary but it is nice to keep the system clean and odor free. Kinda like your furnace filter not necessary but a good idea.

Jul 03, 2009 | 1999 Volkswagen Jetta

5 Answers

I have two noise-related problems with my '99 Lexus rx300.


I had a similar annoying noise with the root cause being found in the air-mix servo. This servo motor box is one of three I believe and is located on the passenger side of the climate control system and accessed by removing the glove compartment (4 screws) and the panel down just above the floor. The servo in question is located behind a couple of heater tubes and you need a stubby phillips screwdriver to remove it. Disconnect the wiring plug. The servo has a damper actuator on one side. Hold with the actuator down and pry open the case. Don't fret if the snaps break because the unit is held together with screws anyway. Clean the contacts inside the box and re-lube the gears and contact plate with silicone grease. Reassemble and reinstall (kind of a pain). Works fine now in my auto (all is quiet again!) and saves hundreds of bucks vs. a visit to Lexus service. Shield the servo from heater tube heat with some aluminum reflective duct sealing tape. I think the heat breaks the lube down and caused the servo voltage to become errant, causing the servo to "hunt" and generate annoying noise. Good Luck.

Jun 13, 2009 | 1999 Lexus RX 300

Not finding what you are looking for?
1999 Lexus RX 300 Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

905 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...