Question about Dodge Durango

Open Question

Cant get 2000 dodge durango to burp has 5.9 magnum engine

Cooling system want get heater warm

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 39 Answers

SOURCE: 2000 Dodge Durango

All you need to do is Remove the POSATIVE cable from the battery for about 25 seconds then reconnect it. This will reset the computer and everything else!

Posted on Jan 30, 2009

  • 1 Answer

SOURCE: cooling system requires burp.

Hey Tim,

I had the same problem with my 1997 Dodge ram 5.2 liter truck. I changed the water pump and it was actually that little o-ring on the heater hose that fits into the water pump on the top right side of the water pump. Also that metal piece on the return heater hose erodes after a while and rusts because it fits inside the water pump. I changed the metal part of the heater hose and the o-ring. I even changed the thermostat because it was easy to access. After I changed all of that I still heard the water running when I would rev the engine. After further investigation, I found that my bypass hose was leaking. The leak was small so I didnt see water on the ground and when the engine was hot it would just evaporate. Changing the bypass hose was more difficult than the water pump. You have remove so much just to get at a 3 to 4 inch hose. After I changed it, I filled up the radiator AGAIN and left the radiator cap off for about 10 minutes and added coolant as the level dropped. It worked, no more water running sound. Hope this helps.
AJ

Posted on Apr 07, 2009

  • 6982 Answers

SOURCE: Can't Burp the cooling system - Overheats

If you can't remove all the air by filling while running with heater on hot, there is a possibility that you have a leaking cylinder head gasket (pressure from there will fill the cooling system and displace coolant) To test, have a shop do a hydrocarbon test on the radiator. Hope I'm wrong, but quite often on those I'm not.

Posted on Apr 19, 2009

  • 323 Answers

SOURCE: 1999 dodge durango heater core

It's a big job. Drain the coolant down, recover the freon in the ac system and disconnect the lines and heater hoses. Lower the steering column, remove the instrument panel assembly, remove the heater housing. Split the case halves on the housing and there you are. Usually around 500 to 700 dollars at a dealership.

Posted on May 29, 2009

Cutlass85
  • 10 Answers

SOURCE: loacte the fuel filter on 2000 dodge durango 4.7 liter v8

if i am not mistaken the fuel filter is built into the fuel pump. which requires you to drop the tank and replace both.

Posted on Jun 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What do I need to change thermostat in a dodge durango magnum 5.2


if its the stat then you will need a 13mm socket and ratchet with extension to remove the bolts that hold the stat housing to the motor. a drain bucket to drain the cooling system below the level of the stat, remove stat and clean surfaces on both the housing and motor. install the new stat and gasket reassemble in reverse order and refill the cooling system and run engine to operating temp and make sure all air is out of system.

May 25, 2014 | 2000 Dodge Durango

2 Answers

I have a 2000 Dodge Durango. The heater blows cold air, the a/c works fine. I was told this could be a bad fuse.


the thermostat that regulates the water temperature is bad. it is in the open position keeping the water from heating

Oct 01, 2013 | 2000 Dodge Durango

1 Answer

I just bought a 2000 4x4 Dodge Durango. The temperature gauge reads properly at about half way, but the heat blows air that is not really hot even though I have the heat at maximum warm. What is the...


try feeling your heater hoses going from the engine to the heater core. they should be hot at operating temperature. If one is hotter than the other noticably it would indicate a restriction in the core most likely. A partially stuck thermostat could also cause loss of heat but you say the temp is normal. Start with checking hose temperature if they are both on the cool side compared to the radiator hose then further diagnostics are necessary. hope this helps. Keep in touch.

Feb 17, 2011 | 2000 Dodge Durango

1 Answer

Where is heater control valve on 2003 dodge ram pick up


THERE IS NO HEATER CONTROL VALVE ON THE WATER HOSES. NEW HEATER CORE. INLET LINE right before heater core hot, outlet after core look warm. Burped cooling system 5 times with engine at operating temp. Installed homade burp VALVE right after heater core outlet(high part of hose). Still no heat. Removed water pump, impeller still in good shape not stripped off shaft. Removed heater core hoses flushed water thrue the connections on the block to the water pump INLET and outlet. flushed water thrue heater core and hoses. Going to put it back togeter today. Used known good gauge to check water temp for operating temp in test. 195 f

Oct 22, 2010 | 1997 Dodge Ram 1500 Club Cab

1 Answer

2001 dodge durango have replaced cooling system neck-vehicle is building too much pressure blowing coolant out of filler cap-could it be thermostat causing problem?


Have you "burped" the system to get all of the trapped air out?? If you have the 4.7 motor, it helps to slightly elevate the front of the Durango.

Then, leave radiator cap off and start engine. Watch coolant level and open the system vent which is right off of the upper hose connection.

When air ceases to come out of the vent, secure it and top off coolant.

It helps to run the engine rpms up to 2-2.5 k in short bursts to help get the air out.

Make sure to have both front and rear heater systems on full heat during this process.

Don

Apr 12, 2010 | 2001 Dodge Durango

1 Answer

Need diagram for firing order to a 2000 Dodge Durango Magnum,4.7


I apologize for the late response...Due to the bad economic situation this site has had a substantial (+50%) increase in the number of questions being asked in the last four months.

For the 4.7L:
Firing Order:
1-8-4-3-6-5-7-2
Cylinders:
8----------7
6----------5
4----------3
2----------1
(Front of Vehicle)

Let me know if this helped, or if you have additional information or questions. Feel free to contact me at FixYa.com!

Feb 01, 2010 | 2000 Dodge Durango

1 Answer

The engin get warm and then the heater come on than it trun to cool and will not get hot


One or more of:

1. Your coolant level is low
2. Your thermostat doesn't close and needs to be replaced
3. The valve from the cooling system to the heater core is stuck
4. Your heater core is clogged

Dec 17, 2009 | 2001 Dodge Durango

3 Answers

Hi when driving my car the enginge doesn't get warm unless the heater is off. Can anyone help?


try checking thermostat. If broken vehicle will not build pressure.

Dec 08, 2009 | 2005 Dodge Magnum

1 Answer

Dodge durango Engine cut's off


Try replacing the fuel filter.

Jun 12, 2009 | 2000 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...