Question about 2004 GMC Envoy

1 Answer

What does a p0410 code mean - 2004 GMC Envoy

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • GMC Master
  • 21,873 Answers

Here is the definition of the code.

P0410 GMC Description An air pump is used on the vehicle to lower tail pipe emissions on start-up. The Powertrain Control Module (PCM) grounds the Air pump relay control circuit which energizes the Air pump. The PCM also grounds the Air combination valve vacuum control solenoid circuit, which energizes the Air vacuum control solenoid. Vacuum is then applied to both Air combination valve diaphragms which opens the shut off valves. The PCM enables both circuits simultaneously when Air system operations id desired. When the AIR system is active, then Air pump forces fresh air into the exhaust stream in order to accelerate catalyst operation. The AIR combination valves replace the conventional check valves. When the AIR system is inactive the shut off valves prevent air flow in either direction.
Possible causes - Faulty Vacuum hoses damaged
- Faulty Air Pump inoperative
- Air bypass solenoid harness is open or shorted
- Air bypass solenoid circuit poor electrical connection
- Air bypass solenoid leaking/blocked or stuck open/closed
- Air diverter valve leaking/blocked or stuck open/closed
Read more: http://engine-codes.com/p0410_gmc.html#ixzz2H3Wjt8f7

Posted on Jan 05, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my 2001 Chev Blazer 4.3 the secondary pump is new and comes on on cold start I'm still getting a p0410 code what could be causing this


check pump new doesnt mean free from defects also check the check valve can be damaged and lastly the fuse may be blown

Mar 31, 2013 | Chevrolet Blazer Cars & Trucks

1 Answer

Code p0410 on pontiac, aztek 2001


A code P0410 may mean that one or more of the following has happened:

  • Water may have collected in the AIR pump or the vent solenoid and frozen or corroded the pump
  • Blown AIR pump fuse due to freezing up

    A code P0410 may mean that one or more of the following has happened:

    • Water may have collected in the AIR pump or the vent solenoid and frozen or corroded the pump
    • Blown AIR pump fuse due to freezing up good-day !

Nov 15, 2011 | 2001 Oldsmobile Intrigue

1 Answer

1999 Saturn p0410


P0410 - Secondary Air Injection System Malfunction
The P0410 code refers to the emissions system. The AIR pump puts air to the exhaust to lower emissions. It takes in outside air and pumps it through two one-way check valves into each bank of the exhaust.

About 90% of the time that this code is set, the one-way check valves have worn out or failed and allow water (which occurs naturally in the exhaust) back into the pump. In any cold climate, especially in climates with higher humidity, this water may be more excessive. The water partially fills the AIR pump, it can then freeze. When the PCM commands the pump on, if the pump is frozen it cannot turn, thus overloading the circuit and "popping" the fuse.

Possibly symptoms include:
MIL illumination obviously
Hesitation on acceleration
Noise from a bad/stuck AIR pump

A code P0410 may mean that one or more of the following has happened:
Water may have collected in the AIR pump or the vent solenoid and frozen or corroded the pump
Blown AIR pump fuse due to freezing up

Hope this helps and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa.
Jose.

Oct 30, 2011 | 2004 Chevrolet TrailBlazer

1 Answer

Am looking for what the carmd code p0410 means for a 2004 buick ranier - my car md is not working right.


CEL light/code P0410, secondary air system fault.
DTC P0410 - Secondary Air Injection System

Suspect -
Relay/fuse (box B) loc 3 ,15amps
Pump $434(new) / $243 (Remanufactured) / $95 (used,Ebay)
solenoid $73
check valve $18
http://www.autopartswarehouse.com

A new pump, or simulator!

What signals the ECU, if the seconary Air Injection system isn't working?
H20 sensors, if running rich > Xtime throw code!
The pump only runs when the engine is cold, so the air & rich fuel mix is burnt in the exhaust manifold, so there's less Emission.

May 09, 2011 | 1997 Volvo 960

1 Answer

I stopped by Advanced Auto because my engine light was on to have them do a diagnostic and it came back with a code P0410. What does this mean?


The link below explains it well. And pay attention to the notes about checking if this is covered under your emissions warranty!

http://www.obd-codes.com/p0410

Jan 20, 2010 | 2005 GMC Envoy

1 Answer

Mazda rx8 fault code p0410 secondary air system we have a mazda rx8 2006 model, p0410 fualt code has come up, want should we looking to check, test and poss change?


The P0410 code refers to the (secondary air system) emissions system. The AIR pump puts air to the exhaust to lower emissions. It takes in outside air and pumps it through two one-way check valves into each bank of the exhaust.
.
About 90% of the time that this code is set, the one-way check valves have worn out or failed and allow water (which occurs naturally in the exhaust) back into the pump. In any cold climate, especially in climates with higher humidity, this water may be more excessive. The water partially fills the AIR pump, it can then freeze. When the PCM commands the pump on, if the pump is frozen it cannot turn, thus overloading the circuit and "popping" the fuse.

A code P0410 may mean that one or more of the following has happened:
  • Water may have collected in the AIR pump or the vent solenoid and frozen or corroded the pump
  • Blown AIR pump fuse due to freezing up
Possible solution:
This may be covered under the emissions warranty on the vehicle. If your vehicle is out of bumper-to-bumper warranty, check if the emissions warranty is still valid!
  • Replace the AIR pump AND one-way check valve
  • Test and clean the AIR pump AND test and replace the one-way air check valve
  • Replace the AIR pump inlet hose
  • Replace the AIR pump fuse (found under the hood)
It is really only an emissions issue and won't harm your car's engine ot drivetrain. It will however mean you won't pass emission testing if you live somewhere that tests for that like I do!

Jun 03, 2009 | 2004 Mazda RX-8

Not finding what you are looking for?
2004 GMC Envoy Logo

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...