Question about 2002 Buick Park Avenue

Open Question

How to install heater bypass hose on a 2002 Buick Park Avenue

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1986 Answers

SOURCE: How do I remove the rear door panel on my Buick Park avenue

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

Ad
  • 115 Answers

SOURCE: 2000 Buick Park Avenue Service engine soon light

need to take car somewhere to have the code read with a scanner,try parts stores first some will do it for free if not the dealers have them

Posted on Sep 15, 2009

c17hydro
  • 2984 Answers

SOURCE: What does trouble code P0171 for a 2002 Buick Park

Trouble Code: P0171 (3.8L V6 VIN 1 Auto)
Fuel Trim System Lean (Bank 1) Print this code dataprint_icon_codes.gif Number of Trips to Set Code: 2
OBD II Monitor Type: CCM Details
Indicators: MIL Details

Trouble Code Conditions:
DTC P0101-P0103, P0107, P0108, P0121-P0123, P0130-P0138, P0140, P0141, P0201-P0206, P0300, P0401-P0405, P0410, P0440-P0446, P0506, P0507, P1404 or P1441 not set, engine started, vehicle driven at less than 82 mph at 550-4000 rpm, BARO sensor over 70 kPa (10.1 psi), ECT sensor from 68-230ºF, IAT sensor from 64-158ºF, MAF sensor from 2.8-150 gm/s, MAP sensor from 16-105 kPa (2.6-15.2 psi), fuel level over 10%, and the PCM detected the Long Term fuel trim value was more than +20% for 6 seconds. The PCM controls the air/fuel metering system to good overall fuel economy, driveability, and emission control. During open loop, the PCM determines fuel delivery based on sensor signals, without the oxygen sensor input. During closed loop, the PCM adds oxygen sensor inputs to calculate Short and Long term fuel trim fuel delivery adjustments. Short Term fuel trim values change rapidly in response to changes in the oxygen sensor signals. Long Term fuel trim makes coarse adjustments in order to maintain an air/fuel ratio of 14.7:1.

Possible Causes:
  • Air leaks in intake manifold, exhaust pipes or exhaust manifold
  • Fuel control sensor is out of calibration (ECT, IAT or MAF)
  • Low fuel pressure (fuel filter clogged, pressure regulator failure)
  • One or more injectors restricted or pressure regulator has failed
  • HO2S element is contaminated, deteriorated or has failed
  • Vacuum hose is disconnected, broken, leaking or loose

Troubleshooting:2002 Buick Park Avenue, 3.8L, P0171

Posted on Nov 01, 2009

  • 355 Answers

SOURCE: How do I bypass 1992-94 buick park avenue security system?

On mine I bypassed it with this solution after it was locked down for weeks: http://newrockies.ca/vatsbypass . This one will bypass the entire system and not only the key and lock cylinder. I wanted to kick the whole system out of my car and never hear about it anymore.

Posted on Feb 10, 2010

ZJLimited
  • 17970 Answers

SOURCE: Need to find heater blower resistor on 1991 Buick

GM: Electra/Park Avenue/Ninety-Eight 1990-1993 REpair Guide
Blower Resistor Module


b4bdc8d.jpg

Fig. 1 Blower resistor assembly is underneath the fuse block
REMOVAL & INSTALLATION

  1. Disconnect the negative battery cable.
  2. Remove the rear sight shield.
  3. Remove the fuse/relay block assembly and bracket.
  4. Disconnect the resistor module connector.
  5. Remove the retaining screws and remove the resistor module.

To install:
  1. Inspect the gasket and replace or repair as required.
  2. Install the resistor module and secure with screws.
  3. Connect the resistor module connector.
  4. Install the bracket and fuse/relay block assembly. Install the sight shield.
  5. Connect the negative battery cable, and check the climate control system for proper operation.
Hope this help (remember rated and comment this).

Posted on Mar 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 02 park avenue an tha radio comes on cd player and tape player works but no sound coming from tha speakers whats tha problem


These cars have an Amplifier to run the speakers. The amp is normally in the truck between the rear 6x9 speakers. The amp is probably fried. You can buy bypass wire harnesses on Ebay that will bypass the failing amp, or simply get a new one.



1999 2000 2001 2002 2003 2004 2005 BUICK PARK AVENUE AUDIO AMP AMPLIFIER...

Feb 21, 2015 | 2002 Buick Park Avenue

1 Answer

Broken water pump bypass hose for a 2002 buick park ave


You will have to remove the belt, altenator and the tensioner bracket. The piece of plastic will be in its bore I've never had one fall in the engine.

Oct 12, 2012 | 2002 Buick Park Avenue

1 Answer

96 Buick Park Avenue, heater wont blow hot air. How can I tell if it might be the thermostat or the heater core?


Start the car and let it warm up. After it is warmed up open the hood. Look for your top radiator hose, and see if you can squeeze the hose, if the hose is hard to squeeze, the thermastat is stuck shut. If your heater core was out, it would be leaking badly.

Feb 26, 2011 | 1996 Buick Park Avenue

2 Answers

How to install a new top and bottom hvac heater hose fitting for a 2002 buick lesabre custom


The hoses are moved by turning them a few degree's, then pulling them off. See diagram below.

658aa5f.gif

Jun 19, 2010 | 2002 Buick LeSabre

1 Answer

Heater does not heat. The inlet and out let of the heater hoses are very warm. The radiator is full.1994 Buick Park Avenue


You have a problem with the ducting. Probably a vacuum leak, could be just a sticky flap also.

Feb 17, 2010 | 1994 Buick Park Avenue

2 Answers

92 buick park avenue won't blow hot air - temp control seems to be working


Make sure there are no leaks and that the system is full to capacity. After the vehicle has warmed up check radiator hoses for temperature differecial also check heater core hoses. A significant difference in temperature may indicate a plugged heater core or thermostat failure

Oct 22, 2009 | 1992 Buick Park Avenue

2 Answers

Buick Park Avenue Security System


I've got my own one stuck for weeks and this was the only thing that brought it to life again : http://newrockies.ca/vatsbypass

Jan 01, 2009 | 1992 Buick Park Avenue

Not finding what you are looking for?
2002 Buick Park Avenue Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...