Question about 1999 Dodge Durango

1 Answer

Transmission 12V Supply Relay Control - 1999 Dodge Durango

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

If your trans is in limp mode, meaning it starts of in second gear and won't shift to higher gears, and your engine light is on because it's pulling up a code for the trans relay having no power to it do the following. On the passenger side of the engine compartment you'll find the computer brain. It will have three plugs on it. Unplug the middle connecter and look for the pink wire. Strip the rubber coating enough to splice another wire to it. Ground the other end of the new wire to a clean ground. This will power the relay and the trans should shift fine. You can drive this way, or buy another brain.

Posted on Jan 07, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my Remote showing relay fault


315Mhz remote relay switch kits - 2 channels - Seeed Studio

www.seeedstudio.com/.../315Mhz-remote-relay-switch-kits-2-channels-p...
This remote switch allows you to remotely control any 12 Volt DC device. ... to supply 3-5VDC to the "+12V" pin,(Caution: the 12v is an error silk screen on PCB, ... Is there a wiring diagram to show how you connect the sender to the GPIO pins?

Amazon.com: 1 Channel Wireless Controller (On/Off) 12V ...

www.amazon.com > ... > Lighting Accessories

Amazon.com, Inc.I wired this remote relay to a fuse block below the motorhome frame. ... Here's a (very) short video showing how the remote control works. I love it! It's very easy to ...

12v wireless 315 MHz remote control relay board 6-channel ...

? 4:36
https://www.youtube.com/watch?v=JBzL0MIno2w
Feb 2, 2013 - Uploaded by Julian Ilett
12v wireless 315 MHz remote control relay board 6-channel ... The relay board takes 12 volts in and there ...

Dec 03, 2015 | Cars & Trucks

3 Answers

What is the most popular item goes bad when throw code po882 on a 2006 pt cruiser non turbo 2.4??


This is a code for the 12v relay supply to the transmission. Check the fuses in the underhood relay/fuse box to make sure none are blown causing this code. If all are ok, it will take electrical diagnostics to isolate the source of the problem by checking wiring/control module etc.

Jun 07, 2015 | 2006 Chrysler PT Cruiser

1 Answer

Fuse for the alarm system


Here is the full list of fuses for you! and for the car.

Fuses on E-box, on left in Engine Compartment

Fuse 1 - Not assigned

Fuse 2 - 10/15A - Engine control unit

Fuse 3 - 5A - Radiator fan control unit

Fuse 4 - 5/10/15A - Lambda probe heater,
Lambda probe 1 heater after
catalytic converter

Fuse 5 - 10A, 20A - Lambda probe heater1,
Lambda probe 1 heater after
catalytic converter,
Fuel system diagnostic pump,
Charge pressure control solenoid
valve,
Exhaust gas recirculation cooler
change-over valve,
Crankcase breather heater element,
Vacuum pump for brakes

Fuse 6 - 5A, 10A,15A - Fuel system diagnostic pump,
Throttle valve module,
Activated charcoal filter system
solenoid valve 1,
Continued coolant circulation pump,
Auxiliary air heater heating element

Fuse 7 - 20A, 5A - Ignition transformer,
Fuel pressure regulating valve,
Fuel metering valve

Fuse 8 - 10A - Throttle valve module,
Activated charcoal filter system
solenoid valve 1

Fuse 9 - 5A - Automatic glow period control unit,
Electric fuel pump 2 relay,
Fuel pump relay

Fuse 10 - 5A - Speedometer sender,
Brake light switch

Fuse 11 - Not assigned

Fuse 12 - 5A - Coolant circulation pump

Fuse 13 - 5A - Water pump

Fuse 14 - 5A - Engine control unit

Fuse 15 - 30A - Voltage stabiliser

Fuse 16 - 30A - ABS control unit

Fuse 17 - 30A - Automatic gearbox control unit

Fuse 18 - 20A - Automatic gearbox control unit

Fuse 19 - 1A - Onboard supply control unit

Fuse 20 - 30A - Onboard supply control unit (AW0)
Automatic intermittent wash and
wipe relay (AW1)

Fuse 21 - 50A - Secondary air pump motor

Fuse 22 - Not assigned

Fuse 23 - 40A - ABS control unit

Fuse 24 - 50A - Trailer detector control unit

Fuse 25 - 50A - Terminal 15 voltage supply relay 2

Fuse 26 - 60A - Automatic glow period control unit

Fuse 27 - 60A - Radiator fan

Fuse 28 - 40A - Onboard supply control unit (AW1)

Fuse 29 - 40A - Onboard supply control unit (AW1)

Fuse 30 - 50A - Terminal 75 voltage supply relay 1

Fuse 31 - 30A - Amplifier

Fuse 32 - Not assigned

**************************************************

Fuse assignment - Interior Fuse Panel

Fuse 1 - Not used

Fuse 2 - 5A - Electronic steering column lock control module

Fuse 3 - 10A - Instrument cluster control module

Fuse 4 - Not used

Fuse 5 - Not used

Fuse 6 - 10A - Vehicle electrical system control module,
Interior ceiling lights,
Tail lights

Fuse 7 - 5A - Fog lamp relay,
Instrument panel and switch illumination dimmer switch,
License plate lamps,
Vehicle electrical system control module

Fuse 8 - 7.5A - Windshield and headlamp washer pump switch,
Windshield washer pump

Fuse 9 - 5A - Airbag control module

Fuse 10 - 10A - Right steering column switch

Fuse 11 - Not used

Fuse 12 - Not used

Fuse 13 - 5A - Automatic dimming interior rearview mirror,
Light recognition sensor,
Parking aid control module,
Air quality sensor,
High pressure sensor,
Climatronic control unit,
Tire pressure monitoring button,
Back-up lamp switch,
Left washer nozzle heater,
Right washer nozzle heater,
28-pin connector

Fuse 14 4- 10A - Left steering column switch,
ABS control module,
Light switch,
Airbag spiral spring/return spring with slip ring,
Fuel pump control module,
Data bus on board diagnostic interface

Fuse 15 - 10A - 16-pin connector (diagnostic connector),
Instrument panel and switch illumination dimmer switch,
Headlamp range control adjuster,
Auxiliary heater operation relay,
Mass airflow sensor,
Positive crankcase ventilation heating element,
Left front headlamp,
Left headlamp beam adjustment motor,
Right front headlamp,
Right headlamp beam adjustment motor,

Fuse 16 - 10A - Engine control module

Fuse 17 - Not used

Fuse 18 - 15A - Left front headlamp

Fuse 19 - 15A - Right front headlamp

Fuse 20 - 10A - Automatic transmission control module,
Selector lever sensor system control module,
Tiptronic switch,
Climatronic control unit,
Ignition/starter switch

Fuse 21 - Not used

Fuse 22 - 10A - Ignition/starter switch,
Converter box,
Alarm horn,
Interior monitoring sensor,
Alarm horn relay,
Dual tone horn relay

Fuse 23 - 10A - Vehicle electrical system control module,
16-pin connector (diagnostic connector),
Light switch,
Rain/light recognition sensor,
Compass magnetic field sensor,

Fuse 24 - 10A - Vehicle electrical system control module,
Access/start authorization control module

Fuse 25 - 15A - Automatic transmission control module,
Selector lever sensor system control module,
Multifunction transmission range switch

Fuse 26 - 15A - Brake system vacuum pump

Fuse 27 - Not used

Fuse 28 - 40A - Auxiliary heater operation relay

Fuse 29 - 1A - Vehicle electrical system control module,

Fuse 30 - 20A - Cigarette lighter,
12 V socket,
12 V socket 2,
Blocking diode

Fuse 31 - 30A - Light switch

Fuse 32 - 20A - Light switch

Fuse 33 - 40A - Heater/heat output switch,
Fresh air blower relay,
A/C control module,
Fresh air blower switch

Fuse 34 - 15A - Left front headlamp,
Left front headlamp,
Instrument cluster control module

Fuse 35 - 10A - Steering column electronics control module,
Instrument cluster control module,
Signal horn activation,
Data bus on board diagnostic interface

Fuse 36 - 25A - Vehicle electrical system control module

Fuse 37 - 15A - Left front headlamp DRL

Fuse 38 - 15A - Right front headlamp DRL

Fuse 39 - 15A - Low beam relay

Fuse 40 - 15A - Towing recognition control module

Fuse 41 - 15A - Towing recognition control module

Fuse 42 - 20A - Towing recognition control module

Fuse 43 - 30A - Front passenger door control module

Fuse 44 - A25 - Rear window defogger relay,
Vehicle electrical system control module

Fuse 45 - 30A - Driver door control module,
Front passenger door control module

Fuse 46 - 30A - Left rear door control module,
Right rear door control module

Fuse 47 - 15A - Fuel pump control module,
Fuel pump relay,
Fuel primer relay

Fuse 48 - 20A - Vehicle electrical system control module,
Vehicle electrical system control module,
Vehicle electrical system control module,

Fuse 49 - 20A - Climatronic control unit,
A/C control module

Fuse 50 - 30A - Front seat heating control module

Fuse 51 - 30A - Power sunroof control module

Fuse 52 - 20A - Dual tone horn relay

Fuse 53 - 15A - Front seat heating control module

Fuse 54 - 15A - Fog lamp relay

Fuse 55 - 20A - Light switch,
Left steering column switch

Fuse 56 - Not used

Fuse 57 - 15A - Radio,
Radio/navigation display unit control module

Fuse 58 - 1A, 30A - Telephone transceiver
DC/AC converter with socket, 12V-230V

Fuse 59 - 30A - Amplifier

Fuse 60 - 30A - Auxiliary heater control module


Hope this helps

--N

May 31, 2014 | 2010 Volkswagen Jetta

1 Answer

What does the code P1765 refer to


Symptom:

P-1765 TRANSMISSION 12V SUPPLY RELAY CONTROL CIRCUIT

When Monitored and Set Condition:

P-1765 TRANSMISSION 12V SUPPLY RELAY CONTROL CIRCUIT

When Monitored: Continuously with the key on.

Set Condition: This code is set if the voltage detected on the Transmission Relay Control

Circuit at the PCM is different than the expected voltage for 3 seconds.

POSSIBLE CAUSES

NO POSSIBLE CAUSES REMAINING

GENERATOR SOURCE CIRCUIT OPEN

TRANSMISSION CONTROL RELAY DEFECTIVE

TRANSMISSION CONTROL RELAY WIR INTERMITTENT DEF

TRANSMISSION CONTROL RELAY WIRING OBSERVABLE DEF

TRANSMISSION RELAY CONTROL CIRCUIT OPEN

TRANSMISSION RELAY CONTROL CKT SHORTED TO GROUND
POWERTRAIN CONTROL MODULE DEFECTIVE

Feb 03, 2012 | 1999 Dodge Dakota

1 Answer

I want to wire 2 driving lamps into my discovery


Instal a relay (preferably in a mounting socket); Wire one side of the control coil to the +12v mainbeam 'on' circuit.
Take the other relay coil control connection to the additional 'Driving-lamp on' control switch (switched to ground).
Supply relay contacts 'common' with a fused +12V from battery - use wire with sufficient current carry capacity to feed driving lights. Connect switched +12V output to the driving lamps.

Oct 27, 2009 | 1998 Land Rover Discovery

1 Answer

How to install fog lights so they come on with the parking lights?


Instal a relay, wire one side of the control coil to the +12v parklight parklight 'on' circuit.
Take the other relay coil control connection to the 'foglight on' control switch (switched to ground).
Supply relay contacts 'common' with a fused +12V from battery.

Oct 10, 2009 | Hyundai Elantra Cars & Trucks

1 Answer

Codes for durango p0443-0753-1765-1494


danbalue, a code P1765 means Transmission 12V Supply Relay Control Conditions and P1494 means EVAP LDP Pressure Switch Fault Conditions.

I found info on the following codes:
P0443 - http://www.obd-codes.com/p0443
P1494 - http://www.check-engine-light.com/dodge

Good luck.

Sep 05, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Blower motor will not work


Do further tests at the relay to ascertain whether the fault lies before or after the relay.
Check power availability at the supply side of the relay contacts - should have 12v from a supply fuse on one side of the normally open contact (note -this supply may only be available when Ign or Acc sw is on).
If power supply is ok at the relay contact, check control input to relay operate coil.

If a ground (or 12v) operates the relay, operate the relay with a local ground (or 12v) and check blower motor runs.

If all above OK, check control signal from fan switch is arriving at the relay control coil.- if not trace wiring back to the switch.

Jul 03, 2009 | Dodge Pickup Cars & Trucks

Not finding what you are looking for?
1999 Dodge Durango Logo

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...