Question about 2005 Hyundai Matrix 1.5

Open Question

Where do the glow plugs go on a matrix ? - 2005 Hyundai Matrix 1.5

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 chevy silverado duramax hd 4WD has codes u1016 /c0035/co201/po673/675/677 but runs great


DTC P0671: Cylinder #1 Glow Plug Control Circuit
DTC P0672: Cylinder #2 Glow Plug Control Circuit
DTC P0673: Cylinder #3 Glow Plug Control Circuit
DTC P0674: Cylinder #4 Glow Plug Control Circuit
DTC P0675: Cylinder #5 Glow Plug Control Circuit
DTC P0676: Cylinder #6 Glow Plug Control Circuit
DTC P0677: Cylinder #7 Glow Plug Control Circuit
DTC P0678: Cylinder #8 Glow Plug Control Circuit

Circuit/System Description
The glow plug controller has the ability to perform internal checks, an open or a short to ground on each of the glow plug circuits. If the glow plug controller senses a problem in a glow plug circuit, the glow plug on the affected cylinder will be disabled and the glow plug controller will send an error message to the engine control module (ECM). If this condition exists, the DTC will set.
Conditions for Setting the DTC
The glow plug controller detects that the glow plug control circuit is open, shorted to ground, or has more than 1 ohm of resistance.

Circuit/System Verification
Verify that DTC P064C is not set.
If DTC P064C is set, refer to DTC P064C.
Ignition ON, engine OFF, observe the scan tool Glow Plug 1-Glow Plug 8 parameters. All 8 Glow Plug parameters should closely match each other.
Refer to Testing for Intermittent Conditions and Poor Connections if you cannot duplicate the conditions.
Engine running, observe the DTC information with a scan tool. DTCs P0671-P0678 should not set.
Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

DTC C0035 Left Front Wheel Speed Sensor Circuit
DTC C0201 Antilock Brake System (ABS) Enable Relay Contact Circuit
The system relay, located within the electronic brake control module (EBCM), supplies battery voltage to all of the valve solenoids and to the ABS pump motor. When the relay contacts close, the EBCM monitors the voltage supplied to the valve solenoids and compares this voltage to monitored ignition voltage.

Jul 30, 2016 | Cars & Trucks

1 Answer

Hyundai matrix


It will shut down if one or more glow plugs is burned out, have them tested.

Mar 19, 2016 | 2005 Hyundai Matrix 1.5

2 Answers

What is the code p0473 for a dodge sprinter van 2008


Error Code: P0404
Fault Location:
Exhaust Gas Recirculation (EGR) System - Range/Performance Problem
Causes:
-Hose leak/blockage.
-Wiring harness.
-Exhaust gas recirculation (EGR) valve/solenoid.
Error Code: P0473
Discription:
Exhaust Gas Pressure Sensor - High Input
Causes:
- Wiring short to positive.
- Exhaust gas pressure sensor (G450).
- Engine control module (ECM).
Error Code: P0674
Description:
Glow Plug Cylinder 4 Circuit - Circuit Malfunction
Causes:
-No Pre-Glow Period.
-Poor Cold Starting.
-Glow Plug Wiring faulty.
-Poor connection.
-Relay.
-Glow plug control module.
-Glow Plug faulty.
-Engine control module (ECM).
Solutions:
Check Glow Plug Wiring.
Check Glow Plug.
Error Code: P0675
Description:
Glow Plug Cylinder 5 Circuit - Circuit Malfunction
Causes:
-No Pre-Glow Period.
-Poor Cold Starting.
-Glow Plug Wiring faulty.
-Poor connection.
-Relay.
-Glow plug control module.
-Glow Plug faulty.
-Engine control module (ECM).
Solutions:
-Check Glow Plug Wiring.
-Check Glow Plug.

Sep 20, 2014 | 2008 Dodge Sprinter

1 Answer

Ecu ig fuse


i guess those are all words with commas missing.
let me guess(sorry)
my engine stalls>? or wont start?
ABS, lock?, brake, and battery lamps glow.
the do when stalled or key on.
why not post all symptoms form a context
eg:
my car will not start
here is what i do ,
i keyon, and the normal (opr.guide stated) lamps all glow
i crank and it cranks good but dont start,
, like that.
there is one more lamp the CEL
it too must glow key on, then go out running, if not, glow key one
the FUSES are blown to ECU.

Dec 07, 2013 | 2009 Toyota Matrix

2 Answers

MATRIX CAM TO CAM TIMING DIAGRAM


Is this the diagram of this engine or do you have the single ohc?6a4c46b.jpg
Single OHC engine
10_4_2012_10_14_34_pm.jpg

Oct 03, 2012 | 2005 Hyundai Matrix 1.6

1 Answer

How do I replace the glow plugs?


  1. Remove the valve cover.
  2. Remove what's needed to gain access to the glow plugs.
  3. Disconnect the electrical connector and remove the intake manifold glow plug from the cylinder head.
  4. Using a deep socket or combination wrench, remove the glow plug from the cylinder head.
  5. Screw the glow plug reamer into the glow plug opening all the way in then out.
  6. Install the new glow plug.
  7. Reconnect the connector to the glow plug terminal.
  8. Replace the valve cover with a new gasket (if required).
  9. Reinstall anything removed for glow plug access.
Hope this helps. Good luck.

Sep 01, 2011 | 1992 Ford F350

1 Answer

Getting a P1391 error code on my 01 Caravan, Changed PCM Sensors, wires, plugs, EGR, Whats Next? Please


P1391 Glow Plug Circuit Low Input (Bank #1)
  • DTC P1391 or P1393 will set when the monitor indicates that all four glow plugs are not being powered on that bank. An open in the glow plug circuits, glow plug relay, glow plugs or monitoring circuit could be the possible causes.

    Both DTCs P1391 and P1393 together will set when the monitor indicates that all eight glow plugs are not being powered. An open in all glow plug circuits, the glow plug relay, glow plugs, fusible links or all three monitoring circuits could be the possible causes.
  • Possible causes:
    • glow plug relay
    • glow plug shunt
    • open in glow plug circuit(s) or monitoring circuit(s)
    • glow plugs
    • PCM
__________________

May 19, 2011 | Dodge Grand Caravan Cars & Trucks

1 Answer

My 2004 f250 after it sits it wont start. the wait to start light only comes on for bout1 to 2 sec. the only way i start it is to plug it up at night what is my problem.


The wait to start light always comes on for at least 1 sec, if it goes off early it must think the engine is warm.

My guess is you have a faulty engine oil temp sensor that is telling the pcm that it is already warm. The only way to know for sure is to read the info with a scan tool.

Glow Plug System: Description and Operation
GLOW PLUG SYSTEM
The 6.0L diesel engine uses a glow plug system that preheats air in the combustion chamber to improve cold engine starting.
The system consists of:
- glow plugs.
- glow plug control module.
- powertrain control module (PCM).
- engine oil temperature (EOT) sensor.
- barometric pressure sensor (BARO sensor).
The glow plug monitor system is part of the On-Board Diagnostics II (OBD II) System.
The glow plug system is electronically controlled by the powertrain control module. If the oil temperature is below 55°C (131°F) the powertrain
control module will energize the glow plugs immediately after the key is placed in the ON position. Then, depending on the readings from the engine
oil temperature (EOT) sensor and the barometric pressure (BARO) sensor, the powertrain control module determines how long the glow plugs will be
on.
The glow plugs are located in the cylinder heads, under the glow plug buss bar.
The glow plugs are self-regulating. If the engine oil temperature is above 55°C (131°F), the powertrain control module will bulb-check the WAIT TO
START lamp but not energize the glow plug relay.
The glow plug ON time varies from 0-120 seconds depending on battery voltage, engine oil temperature and barometric pressure.
The glow plug control monitor (GPCM) system is designed to find failed glow plugs or failed wiring in the glow plug system.

Oct 30, 2009 | 2004 Ford F250

1 Answer

Car won't start...not glow plugs...or battery...garage at a loss.


Just make sure your getting fuel at each injector by cracking them open a little when cranking it over. As long as your getting fuel, and it cranks fast enough, it is impossible for it to NOT start. Deisel engines can be started also with a quick spray of starter fluid, it has to fire, there's nothing to stop it from starting. Just keep at it and be sure it's getting fuel at every cylinder and cranks fast enough. Your only other problem could be the injector pump out of time if you have done anything ay all with it. Best not to have touched that injector pump in the first place, EVER. Lotsa luck pal, ya just gotta stay on it.

Jul 15, 2017 | 2003 Hyundai Accent

1 Answer

Glow plugs causing starting problem


if you need connectors and terminals for the glow plug connections under the valve cover, Ford sells then so you don't need a whole $600 harness.

info for your use

Section 03-07B: Glow Plug System 1996 F-250, F-350, F-Super Duty Equipped with 7.3L Diesel Engines Workshop Manual
DESCRIPTION AND OPERATION Glow Plug System The 7.3L diesel engine uses a glow plug system which preheats air in the combustion chamber to improve cold engine starting. The system consists of eight glow plugs, the glow plug control module (12B533), powertrain control module (PCM) (12A650), engine oil temperature (EOT) sensor and barometric pressure sensor (BARO sensor) (12A644). The glow plug system is electronically controlled by the powertrain control module. The powertrain control module energizes the glow plugs immediately after the key is placed in the ON position and then determines how long the glow plugs will be on according to the engine oil temperature and the barometric pressure. The required time for the glow plugs to be energized decreases as the engine oil temperature and barometric pressure increase. The glow plugs are self-regulating, and the powertrain control module controls relay ON time. The powertrain control module protects the glow plugs by energizing them for short durations if the battery voltage is abnormally high.

Possible Causes: Insufficient glow plug ON time will not allow enough heat to accumulate in the combustion chamber to easily facilitate starting. If the glow plug system ON time does not meet any of the specifications in the accompanying chart the problem is most likely a faulty wire harness connection, ground connections or glow plug relay.

If the glow plug resistance to ground is high, the most likely causes are an open UVC (under valve cover) harness or open glow plug.
--------------------------------------------------------
Relay Operation
Install a DVOM on the glow plug feed side of the glow plug relay (large stud with two wires connected). Turn the ignition key to the ON position but do not attempt to start. Note the time in seconds from when the key is turned on and the glow plug relay energizes until the glow plug relay de-energizes. The glow plug relay makes a loud click noise which is easily heard when it energizes and de-energizes. The dome light will dim and the dash voltmeter will dip when the glow plugs are drawing current from the battery. Compare the times measured to the table (time will be affected by engine temperature, battery condition and vehicle altitude). The voltage at the glow plug feed terminal may vary from 9 to 12 volts depending upon battery condition.
--------------------------------------

-----
If battery voltage not present check for B+ at power supply terminal (terminal with single large wire). Power for glow plug power supply is supplied from starter relay through two fusible links at solenoid.
Glow Plug Operation
Disconnect all of the glow plug/injector harness connectors from the valve cover gaskets. With the pigtail installed, measure glow plug resistance to ground (preferably B-). A resistance measurement of .1 to 6 ohms indicates a good glow plug.



Glow Plug Harness Continuity
Measure for continuity from the connector harness to the glow plug feed terminal on the glow plug relay. Resistance should be less than 5 ohms.
Incorrect measurements will result if all glow plug/injector connectors to valve cover are not disconnected.

---------------------------------------------------
Glow Plug Relay The glow plug relay (12A343) has a plastic base and two mounting bolts. It is operated by the powertrain control module (PCM) (12A650) which senses engine oil temperature, PCM voltage and barometric pressure. When the engine oil temperature or the barometric pressure is low, the PCM activates the glow plug relay and the glow plugs. If the PCM voltage is too high, the powertrain control module deactivates the glow plug relay and the glow plugs immediately energize for a shorter duration, decreasing the modulation of the duty cycle.
-----------------------------------------------
Glow Plug Removal
  1. stj~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE RED-STRIPED WIRING HARNESS CARRIES 115V DC. SEVERE ELECTRICAL SHOCK MAY BE RECEIVED. DO NOT PIERCE.
    Remove valve cover (6582). Refer to Section 03-01D .
  1. Disconnect glow plug electrical connector using a pair of pliers.
  1. Remove glow plug using 10mm socket.
  1. Clean and inspect glow plug tip for damage. Replace if damaged.
Installation
  1. Install glow plug and tighten to 19 Nm (14 lb-ft).
  1. Connect glow plug electrical connector. Make sure glow plug wiring is routed to avoid moving parts.
--------------------------------------------------------------
Glow Plug Control Glow plugs are used to warm the cylinders to improve cold-engine starting. The PCM uses the engine oil temperature (EOT) sensor and barometric pressure (BARO) sensor to determine how long the glow plugs will be on. The PCM energizes the glow plugs longer if the engine is very cold or if the barometric pressure is low at high altitudes.
The PCM controls the relay that supplies power to the glow plugs with the glow plug control (GPC) signal. When the GPC signal is grounded by the PCM the relay closes, turning the glow plugs on.
The glow plugs are controlled by the following sequence:
  1. PCM energizes the glow plugs.
  1. The PCM energizes the glow plugs immediately after the ignition is placed in the ON position.
  1. The PCM then determines how long glow plugs will be on based on EOT sensor and the BARO sensor. The required time to warm up the cylinder decreases the engine oil temperature and barometric pressure increases at low altitudes.
Glow Plug Lamp Control The glow plug lamp (GPL) signal controls the WAIT TO START light located on the instrument panel. This light is used to indicate when to start the engine. The cylinders are being warmed by the glow plugs during and after this light is lit. The PCM energizes the glow plug lamp longer if the engine is very cold or if the barometric pressure is low.
When the GPL signal is brought low, the "Wait to Start" lamp is turned on.
The glow plug lamp is controlled by the following sequence:
  1. PCM lights the WAIT TO START light after a key on reset occurs.
The PCM determines the glow plug lamp activation time based on engine oil temperature, barometric pressure and battery voltage.
  1. PCM turns off the WAIT TO START light.
The glow plug lamp is turned off when the timer counts to the number of seconds specified by the PCM. The glow plugs will normally remain on longer than the "Wait to Start" lamp.
-----------------------------------

Mar 14, 2009 | 2004 Ford F350

Not finding what you are looking for?
2005 Hyundai Matrix 1.5 Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...