Question about 2007 Chevrolet Uplander

Open Question

Uplander alignment I need updated wheel alignment specs that do not show negative camber on the front.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 95 Answers

SOURCE: '95 Camaro wheel alignment specs....

its your lucky day.. i want dave mathews tickets for this :) ok for my camrao which is a 97 z28, which should work for yers heres all the tire and whell specs
Front spec
caster
set ....5.0deg +- 0.5 (+- suppose to be +on top of -)
check...5.0 +- 1.0

cross caster
set....0.0 +- 0.7
check....0.0+- 0.7

Camber
set 0.4 +- 0.5
check...0.4 +- 1.0

Cross camber
set...0.0 +- 0.7
check..0.0 +- 0.7

individual toe
set 0.0 +-0.1
cehck..0.0 +- 0.1

total toe
set 0.0 +- 0.2
check 0.0 +- 0.2

Steering wheel angle
set 0.0 +- 3.5
check ...0.0+- 3.5
i have rear specs too let me know if you need them..Anything you need to know about a f-body just let me know i have 6 manuals on them :)

Posted on May 18, 2009

  • 1146 Answers

SOURCE: I have 2004 chevy impala that needs front wheel

Hi:
Usually the shop that does the alignment will check the status of all four wheels and tell you if they are in or out, before you pay. That was the case for me, when I had an alignment, when I bought new tires. My back tires were wearing ok, but the alignment was slightly off, so I had all four wheels lined up . The cost difference was slightly more than just a front alignment. If you are on a tight budget, then you could let the rear tire alignment go.

Posted on Dec 10, 2009

  • 312 Answers

SOURCE: My '94 1/2 ton 4x4 chevy pickup has a couple

Caster 3.0 + or - 1.0
Camber 0.65
Toe 0.24 + or - 0.2

Posted on Jan 13, 2010

  • 151 Answers

SOURCE: Need front end alignment specs for 1988 Chevy Caprice 4.3

The Caster should be between 2.3degreesand 3.3degrees,Camber should be between +.3 degrees to +1.3 degrees but I myself would recommend closer to the+.3 degrees and as for the Toe should be about 1/16th toed in to not more than 3/32 toe in.

Posted on Apr 24, 2010

  • 1 Answer

SOURCE: Have 44k on a 2008 chevy uplander. Front left

I have a 2008 as well.. with 39K and the front right needed replaced.
it was covered under the 100K warranty

Posted on May 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What causes the drivers side tire to tilt outward


well if its a nascar race car your speaking about then that's called Positive camber !!! and it makes you go faster in the turns ! cus there always turning left !!! if its not a race car your speaking of , then you have a bent front axle it will make the tire loose traction easier and it will make tire wear out faster

Jan 30, 2016 | Cars & Trucks

1 Answer

How to change camber


No, you don't need 15 degrees of negative camber. Most typical specs for camber on the front of a car are between 0.0' and ~ -2.5'.
Note: Cars with -2.0+ degrees of negative camber are usually performance cars like Porsches, Ferrari's, Mercedes AMG models, and so forth.

Jul 07, 2014 | 1987 Vauxhall Astra

2 Answers

Wheel alignment specs


This is just a free chat room

We have no info like that

We are at home & use the site-- the same as you do

Apr 08, 2014 | 2014 Ford Fusion

1 Answer

2011 C70 Front Camber is too agressive, is there anyway to prevent excessive tire wear that is due to negative camber being too large?


Have you had any work done to raise or lower the vehicle? What shape are the struts in? What about accidents ? What is the camber set to now? Did you look into aftermarket camber plates?

Apr 02, 2014 | 2007 Volvo C70

1 Answer

Front Wheel Allignment


On these LH body cars, camber is not adjustable. Neither is caster. Those angles are preset by the suspension geometry. However, specifications for them ARE published. Generally, if either of those two parameters are out of spec, then it's likely something is worn or damaged and needs to be replaced.

The only adjustable parameters are to the front and rear toe but specified as "Total Toe" - see note below.
The alignment specs are as follows ...

ALIGNMENT SPECIFICATIONS AT VEHICLE CURB HEIGHT
A. FRONT WHEELS
  1. CAMBER
    Acceptable -0.6° to +0.6°
    Preferred +0.0°
    Side to Side Differential
    Acceptable 0.7° or less
    Preferred 0.0°
  2. TOTAL TOE - Specified in degrees. See Note Below
    Acceptable 0.4° in -to- 0.0° out
    Preferred 0.2° in
  3. CASTER* (reference angle)
    Acceptable +2.0° -to- +4.0°
    Preferred +3.0°
    *Side to Side Caster Difference not to exceed
    Acceptable 1.0° or less
    Preferred 0.0°
B. REAR WHEELS
  1. CAMBER
    Acceptable -0.6° -to- +0.4°
    Preferred +0.1°
  2. TOTAL TOE** - Specified in degrees. See Note Below.
    Acceptable 0.2° out -to- 0.4° in
    Preferred -0.1° in
    **TOE OUT when backed onto alignment rack is TOE IN when driving.
  3. THRUST ANGLE
    Acceptable -0.15° -to- +0.15°
Note: "Total Toe" is the arithmetic sum of the left and right Toe settings. Positive is Toe-in. Negative is Toe-out. Total Toe must be equally split between left and right wheels. Left and Right Toe must be equal to within 0.02° (2 one hundredths of a degree).

Courtesy RJK & Concorde Shop Manual

Mar 08, 2014 | 1994 Chrysler Concorde

2 Answers

My C70 has way more wear on the inside of the rear wheels. So I took it for new tires and a 4 wheel alliegnment. The tire shop says that this wear is due to excess negative camber and at 2 1/2 degrees on...


2.5 degrees negative camber is not within spec. You need new control arms in the rear. These will set your camber back to the factory setting and reduce your tire wear on the inner edge. The first shop you went to is correct, the camber cannot be adjusted, components must be replaced to rectify the excessive camber. Ive done a couple of New Style C70 rear control arms for this very reason, if your vehicle is under warranty however, the dealer needs to be able to prove that the car needs it. So if you dont have wear on your tires and when the toe was set it readjusted the camber (when you adjust toe it affects camber and caster measurements) then they cant prove to Volvo that it needs the control arms. I hope this helps

Nov 26, 2010 | 2007 Volvo C70

1 Answer

I need to change out the camber bolts. and i cant find the torque specs. can you help


CAMBER BOLT ON THE TIE ROD ENDS.YOU NEED A HAYNES REPAIR MANUAL TO GET THE TORQUE SPECS.YOU PROBABLY NEED WHEEL ALIGNMENT WHENEVER YOU REMOVE TIE ROD ENDS OR UPPER AND LOWER BALL JOINTS IT WILL ALTER WHEEL ALIGNMENT.

Jun 10, 2010 | 2006 Nissan Titan

4 Answers

I keep having to replace wheels on my car.... the wheels are wearing unevenly i took it to a guy and he says the that there is a bar under there that keeps the wheels strait up and that bar is bent so my...


was your car in a wreck since you have own it?
that would be the only way anyone could bend steering or suspension parts.if your tires are leaning out on top,
it would be a part called"lower control arm assembly",
if you stand in front of your car with the steering wheel straight,and your tires are pointing in on each side,or pointed out instead of straight,that would be a "tie rod "
there is an inner tie rod and an outer tie rod end.
you need to take your car to a shop that does alignments,and have them tell you exactly what is wrong,you can even get lower control arm assemblies
from a salvage yard.but do yourself a favor and don't take your car to a MONROE or MIDAS type shop,they are only there to sell and make commissions! Find a normal shop that the owner is the mechanic.

Nov 26, 2009 | 1998 Chevrolet Monte Carlo

1 Answer

'95 Camaro wheel alignment specs....


its your lucky day.. i want dave mathews tickets for this :) ok for my camrao which is a 97 z28, which should work for yers heres all the tire and whell specs
Front spec
caster
set ....5.0deg +- 0.5 (+- suppose to be +on top of -)
check...5.0 +- 1.0

cross caster
set....0.0 +- 0.7
check....0.0+- 0.7

Camber
set 0.4 +- 0.5
check...0.4 +- 1.0

Cross camber
set...0.0 +- 0.7
check..0.0 +- 0.7

individual toe
set 0.0 +-0.1
cehck..0.0 +- 0.1

total toe
set 0.0 +- 0.2
check 0.0 +- 0.2

Steering wheel angle
set 0.0 +- 3.5
check ...0.0+- 3.5
i have rear specs too let me know if you need them..Anything you need to know about a f-body just let me know i have 6 manuals on them :)

Apr 07, 2009 | 1995 Chevrolet Camaro

2 Answers

Front End alignment


Caster +2.5 degrees to +3.5degrees Camber -.5 degree to +.5 degree but Myself for best tire wear the Camber should be set at-.2 degree to +.2 degree. as for the toe it should be set at 0 straight ahead to an 1/8 an inch toed in. I myself preferr 1/16th of an inch toed in.

Dec 06, 2008 | 2001 Dodge Stratus

Not finding what you are looking for?
2007 Chevrolet Uplander Logo

Related Topics:

411 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...