Question about 1989 Ford Ranger

1 Answer

Manual 5 speed transmission 1989 ford ranger

Can release clutch in all gears and nothing happens, when I turn the engine off, i hear what sounds like the transmission free spinning

Posted by on

  • Steve Draper May 11, 2010

    Could be that the clutch plate is stuck to the pressure plate and not allowing it to grab the flywheel.
    Is there plenty of copper grease on the input shaft.?



  • Anonymous Mar 29, 2014

    manual transmission will not go into gear, clutch is engaging.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,198 Answers

Try to see past the slave hose and bleeder to see if you can see the slave work. Could it be stuck in the depressed position? Have a helper push the pedal while you watch. I think your tranny is broke.

Posted on Apr 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 99 ford ranger 5 speed and my gear shift freely moves without pushing the clutch. What will cause that to happen


If the gear shift moves freely and the transmission is turning, I would say the shift lever is not connected to anything, or something inside the trans is broke.
If the trans is not turning, something happened to the clutch.

Nov 09, 2015 | Ford Cars & Trucks

1 Answer

I have a 1989 Ford F150 5 speed manual- Just had new engine mounts fitted as the old ones had split but now can not engage overdrive gear. It will go into gear but feels like it is meeting with a lot


CHECK YOUR CLUTCH LINKAGE AND ADJUSTMENT. REPLACING MOTOR MOUNTS RESTORES ENGINE TO PROPER POSITION AND MAY CHANGE YOUR ADJUSTMENT. SOUNDS LIKE CLUTCH IS NOT RELEASING ALL THE WAY

Nov 20, 2014 | 1989 Ford F 150

1 Answer

94 ford ranger manual transmission goes into first gear and reverse just fine let off the clutch and the truck wont move.


part of a clutch job is removing the gearlever make sure the lever is secured properly and selects the gear correctly.
Orherwise your symptoms sound like a collapsed pressure plate or broken release bearing either defective part or something done wrong during installation of clutch

Apr 13, 2017 | Cars & Trucks

1 Answer

1989 Ford F-150 4.9L 300 inline 6 cylinder 5 speed stuck in 3rd Gear? any solutions


If your clutch master cylinder is good in all other gears: you can disengage and, shift the other gears with the engine not running and, you have the correct amount of clutch fluid
in your clutch master cylinder: to release the clutch:
you have a broken 5th gear syncro and, a bent fork
remove the transmission and, when you remove the shift cover you will
see the problem; you must drain the transmission case remove any metal debris; remove the gear set and, replace the syncro...the fork can probably be
re-straightened use clean, new case oil when you reassemble the transmission.

Aug 04, 2010 | 1989 Ford F 150

1 Answer

I have a 1989 ford ranger five speed manual 2.3 liter 4 cyl i am haveing problems gettin it to go into gear and the clutch is also in the floor but if i turn the truck off it will go into gear and if i...


do this...

make sure the reservoir is full
engine off and pump the clutch pedal slowly about 5-10 times
while holding the pedal down have assistant open the bleeder on the master located in the trans

if you get a good squirt then your concern is the master
if no squirt then replace the slave

neither job is quick but the slave is 1/2 time

Mar 28, 2010 | 1989 Ford Ranger

1 Answer

2003 Ford Ranger-5 Speed. At times is very hard to get into gear


Your clutch is not releasing all the way. (Assuming the problem is not internal to the transmission) Bleed the system. If that doesn't work, rebuild the clutch master cylinder and slave cylinder and bleed again.

Aug 12, 2009 | 2003 Ford Ranger Regular Cab

1 Answer

2000 ford ranger 5 speed problems.


Your clutch disk and pressure plate and throw out bearing need to be replaced.

Jun 26, 2009 | 1989 Ford Ranger

1 Answer

Transmission noise - 93 Honda del Sol w/ 5-spd manual trans.


Imput shaft bearing. It just happened to me. You're looking at a $400 fix.

Mar 22, 2009 | 1994 Honda Civic Del Sol

1 Answer

1989 Toyota Camry


Hi,

On an 89 Toyota Camry with manual transmission, two possible reasons:
  • clutch;
  • release bearing
Try bleeding the clutch on the slave cylinder. If this does not prove to be corrective, you may have to have the transmission/clutch checked/repaired/replaced. In some instances, it could just be a sticking release bearing or clutch fork.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Jul 25, 2008 | 1989 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

458 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

68970 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Ron Lankford

Level 3 Expert

5383 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...