Question about 2003 Nissan Frontier Crew Cab

1 Answer

Blower or fan runs on high speed, only on no. 4 setting.

I know the problem is my blower motor resistor is defective. I want to buy a new one and replace it. Problem is, where is this blower motor resistor network or card is located. I need help in locating this part in the vehicle.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

On the duct work near the fan... two screws usually hold it in.

Robert

Posted on Jan 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

01 grand.prix ac fan switch only works on high. has a duel temp controller when you turn fan off the only way fan comes back on is to move the temp controller levers


Hi!!
When the Blower Motor Resistor (controls blower speeds) goes bad, the blower motor works only on HIGH SPEED. REPLACE IT.
BLOWER MOTOR RESISTOR Removal & Installation
  • Disconnect negative battery cable.
  • Remove right lower instrument panel insulator panel.
  • Disconnect blower resistor connector located behind right side of dash.
  • Remove blower resistor screws and blower resistor.
To install, reverse removal procedure
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa!!

Feb 18, 2011 | 2001 Pontiac Grand Prix

1 Answer

My 99 Camry has done 400K. The blower motor fan stopped working. I checked thge manual, removed the resistor and tried a direct battery feed to motor to check if motor is OK. Motor started working on full...


you know the thing has run 400k miles, that is 300k past it designed life. break down and buy a new fan for it, it will set you back about 60 bucks. if you can replace the resistor, you can change the fan. a new set of plugs, plug wires, and a set of tires may be warranted as well.

Jan 12, 2011 | 1999 Toyota Camry

2 Answers

Vetilation doesn't work in positions 1,2,3, works only in position 4.. help please!


You have got a defective blower motor resistor. Your blower resistor is located just to the left of your blower motor (which is located under the passenger side of your dash. You may find you have a carpeted covered piece of cardboard that is located on the underside of the dash (below the glove box ) if so you'll have to to remove it by removing the retaining clips, Now look up behind the glove box and you"ll see the blower motor and just to the left of it there is rectangular unit with a connector with six wires within the connector , the colors of the wires will be as follows (black and orange)(black and yellow)(two wire's that are black and white)(black and blue)and (black). the blower motor resistor is totally bypassed when you turn your fan speed to high ! The blower speed is controlled by the ground side of the blower. When you request any of the other three speeds the ground circuit is routed through the blower resistor which is made up of three resistors.( resistors reduce the current flow) and each resistor reduces a predetermined about of current.So when you request medium high blower speed the ground circuit runs through one resistor, if you request medium low the ground circuit runs through two resistors , and through three resistors to obtain low blower speed, Normally what happens is the blower resistor blows out the circuit between the fan switch and the blower motor resistor which results in the lost of all lower speeds,no different then the wire to the blower motor just being disconnected.Replace the blower motor resistor and you will in great shape .Thanks for using fixya

Jan 04, 2011 | 2000 Ford Focus

2 Answers

Need to change fan motor control switch? Only works on high setting.


this problem is not caused by the switch, it is caused by a defective blower motor speed control resistor, the resistor is located near the blower motor.

Sep 22, 2010 | 2003 Mercury Grand Marquis

3 Answers

I have a 2002 Elantra. Yestreday the lower fan speeds on the air conditioner fan stopped working (positions 1,2,3). The High speed (position 4) works. Any ideas how to correct?


The blower motor resistors or fan switch itself are defective.
High speed has no resistors B+ goes straight to blower motor.

Jun 03, 2010 | 2000 Hyundai Elantra

1 Answer

Heater fan only works on fastest speed


Your blower motor resistor has gone bad, it should be located next to your blower motor in the car, held in place with a couple of screws, remove it and replace it. The resistor is responsible for making the blower motor run at slower speeds than high or (4). Let me know if this helps.

Jun 16, 2009 | 2000 Ford Focus

3 Answers

A/c fans wont blow


If the fuse is blown for the blower then there is a short, that is not an answer, go to the blower and check to see that the blower motor connector has 12 volts to it when the blower is set to high speed on control, if it does then u need a new blower motor, if it doesn't then the control switch is defective or the blower motor speed control resistor is defective.

May 13, 2009 | 2000 Mercedes-Benz S-Class

1 Answer

Wrangler jeep heater/AC fan


Usually, when the fan works only on high speed the issue is with the blower motor resistor. It will be located under the dash close to the blower motor itself. It will have a multi-wire plug and feeds signal to the blower motor. An updated resistor maybe available in which case a slightly larger hole will have to be cut for the new resistor. This is not a difficult proceedure, only a couple of screws are holding the resistor in place and most resistors are resonably priced. I recommend you buy the resistor at the dealer, this is a case where you get what you pay for.
Good luck, hope this helps.

Jan 18, 2009 | 2003 Jeep Wrangler

1 Answer

Vent fan only works when set to 4


Hi.....
On your Vehicle the problem for the FAN speed is NOT the FAN switch.
99.9 % of this problem on cars is the BLOWER MOTOR RESISTOR.
The blower motor resistor give the speed to the Fan.
But on High speed the switch make a By pass of the switch using a Relay for the high speed.
The Blower motor resistor, is located Beside of the Blower motor On the passanger compartment.

If you replace the blower motor resistor you have 99.9% of this will solve your problem.

I'm a Mechanic.

I hope this help on your problem.
Thank you for use fixya...

Oct 09, 2008 | 2003 Nissan Altima

Not finding what you are looking for?
2003 Nissan Frontier Crew Cab Logo

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...