Question about 2000 Mercury Mountaineer

Open Question

Mercury mountaineer driver door won't unlock - 2000 Mercury Mountaineer

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 119 Answers

SOURCE: entry code om drivers door

The keyless entry module is located in the rear of the vehicle on the driver's side. You will need to partially remove the left rear panel in the cargo area. You will then see the keyless entry module bolted behind a metal reinforcement bar. There is a sticker on the module that has the 5 digit entry code.

Posted on May 26, 2008

blueextc3221
  • 15935 Answers

SOURCE: driver sode door lock

The locking solenoid may need to be replaced, or the rod adjusted.
You will need to remove the door panel to watch the movement.
If the solenoid is not fully extending, it will require replacement.
It will look similar to this...
7fbc21e.jpg
In the picture below, it will be #4

47cdcd4.gif Check the locking mechanism is lubricated properly. Try spraying some penetrating oil in the mechanism (just above 3 in the diagram) Wait 10 minutes, and re-try.
If the actuator does not fully extend, it will need to be replaced.

Posted on Jan 15, 2009

michigan man
  • 3533 Answers

SOURCE: Goodmorning! I had purchased a 2000 mercury

spray a small amount of W/D 4o into the key lock and then put the key in and move it back and forward until the lock free up and also spray a small amount in the inside lock of the door as well and then do the same on the other side the reason you had this problem is because the last owner only used the remotes to lock and unlock the doors and not the key sometimes.

Posted on Mar 18, 2009

  • 396 Answers

SOURCE: 2006 mercury mountaineer interior lights will not shut off

There is some problem with the door switch(s) which should turn the lights off when the door is closed. Look closely at the switch and make sure that the proper contact is being made within the switch. There could be corrosion.

Posted on Oct 11, 2009

  • 18 Answers

SOURCE: I cannot open rear driver side door from inside or out.

Well you could take the door panel off and fool around with the lock till you get it to work. If you want to get lazy take a crow bar and open the door with that, but it will more than likely break the door. Sounds the lock seized up and will take you working to get it loose,

Posted on Oct 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 mercury mountaineer door opens but won't lock on driver side. all other doors lock. What can be wrong?


The lock actuator is broken. Seems as if it went out in the unlock position. So you cant lock it. Replace the actuator and you will be able to lock it again.

Mar 07, 2014 | Cars & Trucks

1 Answer

The latch to unlock the drivers door with the key is broke need to find the part to fix it


I don't list the door lock cylinder available aftermarket, so you will probably need to get it from a Ford dealer.

Aug 01, 2012 | 2000 Mercury Mountaineer

1 Answer

Electric lock on drivers door won't come up all other doors work fine


The most likely cause of this is that the power door lock motor has failed, you will need to replace it. Please watch this video at YouTube.

Jun 17, 2012 | 1998 Mercury Mountaineer

1 Answer

97 Mercury Mountaineer driver side door won't open. Outside handle flops around; inside handle won't open door


Try a slim jim first, down the side of the window. Or AAA or locksmith. If no luck, remove the seat first. Find the screws and bolts around the door handle and arm rest. Most Ford's have screws around the outer side of the panel. I don't believe your's does. The panel lifts or pops off. Once the panel is off, you can reach down and open the door. Just a note. I have done some to where the panel came out in pieces.

Mar 14, 2012 | 1997 Mercury Mountaineer

2 Answers

My power locks wont work on my 04 mercury mountaineer


Obviusly, check fuses. Do they operate from the passenger door control? When ever you have a problem with a door switch on the driver's door, always check wire integrity in the driver's door jam harness.

Jun 18, 2011 | Mercury Mountaineer Cars & Trucks

2 Answers

Where do I find the keyless entry code for my 1999 Mercury Mountaineer? Then when I use the remote to unlock or lock the Mountaineer, the locks will pop up or the horn will blow or all four locks will...


TRY THIS REPROGRAMMING PROCEDURE. SWITCH THE IGNITION OFF TO ON 8 TIMES WITHIN 10 SECONDS. DOORS SHOULD LOCK THEN UNLOCK. PRESS ANY BUTTON ON THE FIRST REMOTE TRANSMITTER. DOORS SHOULD LOCK THEN UNLOCK. IF YOU HAVE ANOTHER CAR REMOTE REPROGRAM IT THE SAME WAY. WHEN DONE SWITCH IGNITION SWITCH OFF.

Jan 27, 2011 | 1999 Mercury Mountaineer

1 Answer

Removing 97 mountaineer door panel


just let someone replace it for you , because by the time you do this and that , you won t have a panel left ..............

Jan 21, 2009 | 1997 Mercury Mountaineer

Not finding what you are looking for?
2000 Mercury Mountaineer Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...