Question about Cars & Trucks

1 Answer

I just changed the starter on my 1995 chevy s10 pick up 2.2l 4cyl 2wd.. i forgot to remove the battery and tried to tighten the bolt some more and got shocked. Now my truck will start but wont stay on. Checked fuses there ok i checked battery and alternator there ok. Could it be the coil pack?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,036 Answers

Check starter fuse link and alternator fuse link and check ignition fuse and PCM fuse

Posted on Jan 04, 2013

  • 1 more comment 
  • Jas M Jan 04, 2013

    I did the fuses were all good

  • Jonah Oneal Jan 04, 2013

    check see if you have reverse light in reverse if not could have damaged transmission neutral safety switch or alternator.

  • Jonah Oneal Jan 05, 2013

    check see if fuel pump running turn on ignition for 3 seconds see if fuel pump running.

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1118 Answers

SOURCE: 2003 Chevy S10 won't start

Are you sure its the starter? did you try it in neutral? could be park neutral switch, or ignition switch, or if its a standard shift maybe it has a switch on clutch that it has to be depressed to start and its bad. As far as jump starting you cross the maine or big post on starter to small or little post on starter to do that, on a v6 starter it on the right side under exhaust manafold, and i think its on the same side on a 4 cyl.

Posted on Feb 10, 2009

  • 39 Answers

SOURCE: My s-10 truck, 99 model,2,2L; wont start due to a

i had the same problem on my 98 sonoma. for some reason your passlock system did not recognise your key and went into security. you have to take it to a dealer or a shop with a computer and have them reset your passlock. if you have a buddy or know someone with a scan tool they may be able to do it to. i think the shop here charged $35. but there is no other way to fix it.

Posted on Mar 16, 2009

  • 1 Answer

SOURCE: Chevy S10 Pickup Starter. Removed the two bolts

Just changed a starter in a 94 S10 4x4. The only way to remove the starter was to take the passenger side exhaust manifold off and bring the starter out that way. Installation the same in reverse. Hope this helps. Don

Posted on Jun 25, 2009

dennymulford
  • 1055 Answers

SOURCE: I have a 1998 Chevy S10 pick up, have a starting

can you turn the engine by puting a wrench on the harmonic balencer? if not then the engine is locked up!!! if you can turn it this way then check your battery conections and body grounds!!

Posted on Dec 28, 2009

  • 82 Answers

SOURCE: i have a 1992 chevy S10 with a 4.3L it cranks

I'm assuming that you verified that the distributor is rotating. Verify that you have good secondary wires. verify that your pimary circuit is good.

Posted on Mar 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know how to get the bolts off a nissan pathfinders starter motor


Nissan Pick-ups and Pathfinder 1989-1995
Starter - REMOVAL & INSTALLATION
(see Figures 1 and 2)
  1. Disconnect the negative battery cable at the battery, then disconnect the positive battery cable at the starter.
e757468.jpg
Fig. 1: Starter removal on 4WD-6-cylinder engine


4643c02.jpg
Fig. 2: Starter removal on 2WD-6-cylinder engine
  1. On 4wd models with the 6-cylinder engine:
    1. Remove the front gravel shield.
    2. Detach the oil pressure switch connector.
    3. Drain the engine oil and remove the oil filter.
CAUTION The EPA warns that prolonged contact with used engine oil may cause a number of skin disorders, including cancer! You should make every effort to minimize your exposure to used engine oil. Protective gloves should be worn when changing the oil. Wash your hands and any other exposed skin areas as soon as possible after exposure to used engine oil. Soap and water, or waterless hand cleaner should be used.
  1. On 2wd models with the 6-cylinder engine:
    1. Remove the front right wheel.
    2. Remove the front gravel shield.
    3. Remove the exhaust manifold heat insulator.
    4. Remove the exhaust manifold.
    5. Detach the oil pressure switch connector.

  2. Unfasten the remaining electrical connections at the starter solenoid.
  3. Remove the two nuts holding the starter to the bell housing, then pull the starter toward the front of the vehicle and out.
To install:
  1. Insert the starter into the bell housing, being sure that the starter drive is not jammed against the flywheel.
  2. Tighten the attaching nuts and secure all electrical connections to the starter assembly.
  3. Install all remaining components in reverse order of removal.
  4. Reconnect the battery cables. If applicable, refill and check the oil level. Check the starter assembly for proper operation.

Also can check here other DIY.

Hope helped with this (remember rated and comments this help).

Mar 03, 2010 | 1995 Nissan Pathfinder

1 Answer

Need detailed directions to remove starter from chevy s10


disconnect negative battery terminal unbolt starter from engine i think they are 14mm bolt maybe 15mm and take the 2 wires off making sure when you install new starter the wires go back where they came from the starter should come right down the reinstall in reverse order

Nov 11, 2009 | 1995 Chevrolet S-10 CA Edition

2 Answers

How do I remove and replace a starter from a 1993 Toyota Previa? I am told it's rather difficult and may include removing something from the automatic transmission.


Removal & Installation
  1. Disconnect the negative battery cable from the battery.
  2. Raise and safely support the vehicle.
  3. If equipped with 4WD, remove the front drive shaft.
  4. Remove the nut and disconnect the starter wire.
  5. Disconnect the starter connector.
  6. Remove the bolt holding the starter stay to the upper stiffener plate.
  7. If equipped with 2WD, remove the starter by removing the nut and three bolts.
  8. If equipped with 4WD, remove the starter by removing the nut, four bolts, and the center bracket.
To install:
  1. If equipped with 4WD, install the starter, the center support bracket, nut, and the four bolts.
  2. If equipped with 2WD, install the starter, nut and three bolts.
  3. Install the bolt to hold the starter stay to the upper stiffener plate. Tighten the bolt to 43 inch lbs. (5 Nm).
  4. Install the starter connector.
  5. Connect the starter wire with the nut. Tighten the nut to 78 inch lbs. (9 Nm).
  6. If equipped with 4WD, install the front drive shaft.
  7. Connect the negative battery cable.
Good luck and this should take about 2 1/5 hours from start to finish and if you like, use lock tight medium strength to make sure the bolts don't go lose on you.

Nov 04, 2009 | 1991 Toyota Previa

1 Answer

How to change starter on 2000 chevy silverado


These instructions are for a 5.3L. Unless it is a V6 or diesel, the instructions will be similar if you have a different gas V8.
  1. Disconnect the negative battery cable
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  3. Remove the protective shields as necessary.
  4. Remove the starter solenoid shield.
  5. Remove the starter to transmission close out cover bolt.
  6. Disconnect the engine oil level sensor connection.
  7. Remove the front axle mounting bracket through bolt nut, if equipped with four wheel drive (4WD).
  8. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt, if equipped with 4WD.
  9. Remove the mounting bolts from the engine block.
  10. Slide the starter forward until the starter clears the transmission.
  11. Remove the starter transmission close out cover
    1. Disconnect the positive battery cable and wiring harness from the starter.
    2. Remove the starter from the vehicle.
      1. Connect the positive battery cable to the starter. Tighten Tighten the nut to 16 N.m (12 lb in) .
      2. Install the starter transmission close out cover.
        1. Install the mounting bolts to the engine block. Tighten Tighten the bolts to 50 N.m (37 lb ft) .
        2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated. if equipped with 4WD.
        3. Install the front axle mounting bracket through bolt nut, if equipped with 4WD. Tighten Tighten the nut to 90 N.m (67 lb ft) .
        4. Disconnect the engine oil level sensor connection.
        5. Install the starter to transmission close out cover bolt.
        6. Install the starter solenoid shield.
        7. Install the protective shields as necessary.
        8. Remove the safety stands.
        9. Lower the vehicle.
        10. Connect the negative battery cable. Tighten Tighten the bolts to 17 N.m (13 lb ft) .

Oct 01, 2009 | 2002 Chevrolet Silverado

2 Answers

How to replace starter on 1998 isuzu amigo 2wd 4cyl


Removal
1. Battery ground cable.
2. Remove harness connectors
3. Remove bolts from starter.
Installation
1. Install starter assembly.
2. Install mounting bolts and tighten bolts to specified
torque
Torque: 25 N·m (18 lb ft)
3. Connect harness.
4. Reconnect the battery ground cable

Jul 02, 2009 | 1998 Isuzu Amigo

2 Answers

Chevy S10 Pickup Starter. Removed the two bolts


Just changed a starter in a 94 S10 4x4. The only way to remove the starter was to take the passenger side exhaust manifold off and bring the starter out that way. Installation the same in reverse. Hope this helps. Don

Mar 14, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

REPLACE STARTER ON 1995 CHEVY S-10PU 4.3 LTR


step1 Turn the truck off and disconnect the battery. Lift the car with a jack and place jack stands under the frame of the truck. Block the rear wheels to prevent the truck from rolling backwards. Step2 Locate the starter and remove the wires connected to it. Mark them so you know which is positive and which is negative so you can reconnect them accordingly. Step3 Remove the bolts holding the starter in place. There are usually two or three bolts holding the starter. Step4 Pull the starter out of its position and remove it from the truck. Some other parts may need to be loosened or removed for the starter to be removed from the truck. Remember what parts are removed or loosened. Step5 Put the new starter in the truck by installing it the same way the old starter was removed. Tighten the bolts slightly, connect the wires to the starter and then tighten the bolts completely. Step6 Replace any other parts in the truck that were removed or loosened. Lower the truck from the jack stands, remove the blocks from the rear wheelsmag-glass_10x10.gif and reconnect the battery. Start the car to make sure everything is working properly.

Feb 25, 2009 | 1995 Chevrolet S-10 CA Edition

1 Answer

Removing starter heat shield on 2000 Passat 4cyl Turbo


I am not sure if I have the right engine but this may help and give you a better idea of what you are doing.

2-Wheel Drive (2wd) Models (2wd) Models
2.2L Engine
  1. Remove or disconnect the following:
    • Negative battery cable
    • Front exhaust pipe, if necessary for access
    • Starter heat shield, if equipped
    • Brace rod from the front of the engine and the bell housing
    • Drivers side wheel to access the starter motor wires and the starter motor attaching bracket-to-engine bolt through the opening in the wheel well
    • Wires from the starter solenoid
    • Attaching bracket-to-engine mount bolt
    • Starter-to-engine block bolts. When removing the last bolt, be sure to support the starter to keep it from falling and possibly injuring you.
    • Starter and shims (if equipped) from the vehicle
    • Bracket from the starter assembly, if equipped 0900c15280096824.jpgStarter motor and related components—2.2L engine
To install:
  1. Install or connect the following:
    • Bracket to the starter, if removed. Tighten the bracket nuts to 97 inch lbs. (11 Nm).
    • Starter and shims (if equipped) into position in the vehicle and thread one of the retaining bolts to hold it in position.
    • Bracket-to-engine mount bolt (loosely), if equipped
    • Starter mounting bolt, then tighten all mounting fasteners to 32 ft. lbs. (43 Nm)
    • Wiring to the solenoid
    • Brace rod and tighten the retainers
    • Front exhaust pipe and tighten the fasteners, if removed
    • Starter heat shield, if equipped
    • Driver’s side wheel, if removed
    • Negative battery cable

Nov 27, 2008 | 1999 Chevrolet Tahoe

1 Answer

Chevrolet S10


Well,it depends on the facilities you have to work with.Hand tools versus air tools.Professional car hoist,or jackstands and a floor jack.You also did not specify 2wd or 4wd,as a 4wd has 2 driveshafts versus one for a 2wd...etc.You also didn't specify automatic or manual trans.Generally speaking,with the facilities i have at work,and air tools,transmission jack,etc.For a 2wd truck,about 1- 2 hours to remove,and 2-3 hours to reinstall.For a 4wd truck,about 2-3 hours to remove,and 3-4 hours to reinstall.Now that's presuming the truck is from down south and not all rusted up,because rusted bolts adds considerably to labor times,and makes a set of torches mandatory.These times i have quoted are coming from an older man that's slowing down some.In my prime years,i could remove a 2wd trans from your truck in about 30 minutes,so,the time is relative to ability too.

Jul 18, 2008 | 1995 Chevrolet S-10 CA Edition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...