Question about 2007 Ford Fusion I4 SEL Sedan

Open Question

What is 2006 Ford Fusion code PO410, PO491 - 2007 Ford Fusion I4 SEL Sedan

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 12 Answers

SOURCE: code P0128 ford, fusion 2006 4 cly

I had the same code. It means your engine coolant temp. is too low. That means your thermostat needs to be changed. Get the Ford Motorcraft one. It comes with the entire housing. Have a mechanic replace it. It is a real bugger to get to.

Posted on Mar 29, 2010

Ad
  • 972 Answers

SOURCE: 2006 Ford Fusion a/c not working

its inside the hvac box under the dash you may or may not have to romove the hvac unit to change it. circuit high means an open circuit so check connectors and such

Posted on Apr 15, 2010

toneman2121
  • 775 Answers

SOURCE: removing alternator on a 2006 ford fusion v6

the alternator probably is accessable from the underside of the car without removing the compressor, which would require extensive knowledge and expensive equipment. the best thing to do is purchase a repair manual. this inexpensive investment has detailed procedure and pictures to help you tackle this repair.

Posted on May 25, 2010

alicantecoli
  • 22219 Answers

SOURCE: How do you fix a P0128 code on a 2006 Ford Fusion?

Upstream HO2S Sensors Swapped or this one
P0128....Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) now if this a 2006 model built for the europeon market then your code reader is a waste of time as it will never read the correct codes and if your really lucky it could lock up the immobilisor as well this is to prevent general garages from doing any repairs so just take it back to a ford garage

Posted on Jul 30, 2010

  • 21 Answers

SOURCE: p0128 code on 2006 ford

Your vehicle needs a thermostat. It is a pretty simple repair. Its under the left side of the intake manifold. You have to get one of the bolts from the bottom and the other two from the top.

Posted on Sep 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know what code 2110 ford fusion 2006 se


P2110 2006 FORD FUSION P2110 2006 FORD FUSION - Throttle Actuator Control System - Forced Limited RPM 0 Comments ' Add Yours Possible causes - Faulty Throttle Actuator Control (TAC)
- Throttle Actuator Control (TAC) harness is open or shorted
- Throttle Actuator Control (TAC) circuit poor electrical connection help.png Help with this Symptoms - Engine Light ON (or Service Engine Soon Warning Light P2110 2006 FORD FUSION Description The TAC system is in the failure mode effects management (FMEM) mode of forced limited RPM.

Read more: http://helpforcars.net/obd_codes/p2110_2006_ford_fusion.html#ixzz3mV0SayWu

Sep 22, 2015 | 2006 Ford Fusion

1 Answer

What does 2110 code on 2006 ford fusion mean


P2110 2006 FORD FUSION P2110 2006 FORD FUSION - Throttle Actuator Control System - Forced Limited RPM 0 Comments ' Add Yours Possible causes - Faulty Throttle Actuator Control (TAC)
- Throttle Actuator Control (TAC) harness is open or shorted
- Throttle Actuator Control (TAC) circuit poor electrical connection > Help with this Symptoms - Engine Light ON (or Service Engine Soon Warning Light P2110 2006 FORD FUSION Description The TAC system is in the failure mode effects management (FMEM) mode of forced limited RPM.

Read more: http://helpforcars.net/obd_codes/p2110_2006_ford_fusion.html#ixzz3mUz73ACP

Sep 22, 2015 | 2006 Ford Fusion

1 Answer

2007ford fusion code po410 and po491


The Secondary Air System pumps outside fresh air into the Exhaust System during cold engine start up. This additional air helps burn up the highly rich exhaust emissions that are produced when the engine is warming up. The Secondary Air System typically has an Air Pump and some tubes or plumbing to route the air. The system also has a solenoid and Check Valve(s) to control the air flow.

Apr 09, 2013 | 2007 Ford Fusion I4 SEL Sedan

1 Answer

Codepo491


Manufacture Code

Google it

As with all codes, you have a repair shop
use the codes to diagnose the failed system

Mar 09, 2013 | 2006 Ford Fusion

1 Answer

Code po491 on my 07 fusion


Code 491 is for insufficient secondary air injection flow bank one.
There is a device that pumps fresh air into the exhaust system to lower emissions. The sensor that measures air flow is telling the computer the air flow is below standard.
The system would need to be tested.

Jan 21, 2013 | 2007 Ford Fusion I4 SEL Sedan

2 Answers

I have the following codes po410 and po491.......can u please tell me what they are so I can get my car fixed asap


P0410 - SECONDARY AIR INJECTION (AIR) SYSTEM
P0491 - SECONDARY AIR INJECTION (AIR) SYSTEM INSUFFICIENT FLOW (BANK 1)

Secondary air injection (trademarked as Air Injection Reactor) is a process where fresh air is injected into the exhaust system to allow for a fuller combustion of exhaust gasses.

The possible causes are:
SAIR pump low or now air flow
SAIR bypass solenoid leaking/blocked or stuck open/closed
SAIR diverter valve leaking/blocked or stuck open/closed
SAIR air hose restriction
SAIR vacuum hose restriction or leaking

Check to make sure your air filter isn't dirty - and replace if needed. Otherwise I would suggest having your local trusted auto repair facility diagnose and repair the issue. A scan tool will be needed to properly diagnose the issue.

May 27, 2011 | 2006 Ford Focus

1 Answer

My 2006 ford fusion check engine light is on and


P0882 - TCM Power Input Signal Low, this is a transmission code, I recommend that you take it to a dealer or qualified transmission shop. Hope this helps.

Jul 05, 2010 | 2006 Ford Fusion

1 Answer

Code P0128 ford, fusion 2006 4 cly


I had the same code. It means your engine coolant temp. is too low. That means your thermostat needs to be changed. Get the Ford Motorcraft one. It comes with the entire housing. Have a mechanic replace it. It is a real bugger to get to.

Mar 28, 2010 | 2006 Ford Fusion

Not finding what you are looking for?
2007 Ford Fusion I4 SEL Sedan Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...