Question about 2001 Isuzu Rodeo

Open Question

Isuzu rodeo 4by4 2001 app sensor - 2001 Isuzu Rodeo

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

brandyspoile
  • 61 Answers

SOURCE: Crank Sensor in 94 Isuzu Rodeo

it's on the bottom of the motor, towards the back on the passenger side. It has a small clip of wires and one screw holding it on. You may want to pull it up on ramps- if it'll run- otherwise, get under the Rodeo, it's up a little higher than the oil pan, and to the passenger side. (it's right on top of the two lines that run to the bottom of the radiator.) You will need a 10mm socket to remove it. I have added a few pics showing the location (i just completed this task myself)
bfcf016.jpg61ae995.jpgdeffbd6.jpgdd2e415.jpg

Posted on Jul 24, 2009

  • 1 Answer

SOURCE: 99 isuzu rodeo sensor problem

My abs sensor light comes on and off when I'm at at certain speed, I need help.

Posted on Mar 15, 2009

  • 150 Answers

SOURCE: WHERE DOES THE KNOCK SENSOR, AND OXYGEN SENSOR GO?

The knock sensor is located on the side of the engine block. And the oxygen sensors are located in the exhaust system. There will be one oxygen sensor (upstream) screwed into either the exhaust manifold or the exhaust pipe before the catalytic converter. The other oxygen sensor (down stream) will be screwed into the exhaust pipe just after the catalytic converter.

Posted on May 13, 2009

  • 14 Answers

SOURCE: 2001 Isuzu Rodeo 4 cyl 2.2L 2WD that is overheating

check the electric fan conector plug some times is rusti scratchet whit a sharp scruwdriver remove the rusti or dirt on it this happens many times and step two check the relay and thats it (this is the first step a mecanic to search)

Posted on Feb 07, 2010

  • 137 Answers

SOURCE: where is MAF sensor on 1994 isuzu rodeo Runs rough

The sensor should be right there where the intake air duct meets the air filter housing.
That oil down in the spark plug tube is most likely from a leaking valve gover gasket. Oil in there can and will cause misfires.

Posted on Oct 07, 2010

Testimonial: "very grateful for any and all assistance. Female with an old Rodeo. Thanks a bunch!!!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace a 2000 Isuzu Rodeo Speedometer Sensor


there are two vehicle speed sensors on the 2000 rodeo 4x4. One on the left side of the transmission case and one on the right side of the transfer case, the one that located on the transfer case

Jun 04, 2014 | 2000 Isuzu Rodeo

1 Answer

2002 isuzu rodeo 2.2 liter code P0341 cmp range or performance problems


P0341 ISUZU - Camshaft Position Sensor Performance
Possible causes- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Sep 10, 2012 | 2002 Isuzu Rodeo

1 Answer

Where is MAF sensor on 1994 isuzu rodeo Runs rough


The sensor should be right there where the intake air duct meets the air filter housing.
That oil down in the spark plug tube is most likely from a leaking valve gover gasket. Oil in there can and will cause misfires.

Oct 07, 2010 | 1994 Isuzu Rodeo

2 Answers

Is the 1994 Isuzu Rodeo v6 compatible with the 1997 Isuzu Rodeo as far as engine parts...alternator, MAF sensor..etc?


go to the rockauto.com site and compare part numbers for each year and see if they are the same.

Sep 08, 2010 | 1997 Isuzu Rodeo

1 Answer

Not getting any fire in 94 isuzu rodeo


SWITCH ASM; POWER,IGN COIL 8-94474-294-2 Go to myisuzuparts.com and find this part number. This part is under the intake manifold. No crank sensor as is has a distributor. 8-94474-294-2 1 05-1990 to 08-1994




Feb 22, 2010 | 1994 Isuzu Rodeo

2 Answers

Crank Sensor in 94 Isuzu Rodeo


it's on the bottom of the motor, towards the back on the passenger side. It has a small clip of wires and one screw holding it on. You may want to pull it up on ramps- if it'll run- otherwise, get under the Rodeo, it's up a little higher than the oil pan, and to the passenger side. (it's right on top of the two lines that run to the bottom of the radiator.) You will need a 10mm socket to remove it. I have added a few pics showing the location (i just completed this task myself)
bfcf016.jpg61ae995.jpgdeffbd6.jpgdd2e415.jpg

Jul 13, 2009 | 1994 Isuzu Rodeo

1 Answer

Need to know where the o2 Sensor is located on a 1998 Rodeo.


look on the y pipe just in front of the cats.......

Jun 24, 2009 | 1998 Isuzu Rodeo

Not finding what you are looking for?
2001 Isuzu Rodeo Logo

Related Topics:

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...