Question about 2008 Chevrolet Uplander

Open Question

2008 chevy uplander stability system active message

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

lindsay836
  • 677 Answers

SOURCE: 2008 Chevrolet Uplander. The car activates abs for

• An internal fault within the yaw rate sensor/lateral accelerometer, P/N 15189628, may be the first possible cause. • The vehicle stability enhancement system (VSES) electronic brake traction control module See if this info helps

Posted on Feb 05, 2010

  • 1 Answer

SOURCE: Have 44k on a 2008 chevy uplander. Front left

I have a 2008 as well.. with 39K and the front right needed replaced.
it was covered under the 100K warranty

Posted on May 04, 2010

  • 11192 Answers

SOURCE: have to replace a chevy uplander 2008 left rear

open rear hatch and will see the access screws un screw careful not to drop and pull away like opening a door and assembly is free from van

Posted on Jun 10, 2010

  • 1168 Answers

SOURCE: My stability system and traction

Hello Tip.

All three systems rely on some of the same sensors in order to operate.
In this case most likely is wheel speed sensors. By far the most common problem.
The system will need to be scanned to find out which is the offending one and be repaired.
Not all scan tools have the capability to read ABS systems. Make sure whoever you take it to has this available. Most good shops will have this.
If you have further questions on this, please ask me here, be glad to help.
Thank you for using FixYa.

KL

Posted on Jan 17, 2011

  • 1608 Answers

SOURCE: my 2008 chevy uplander engine

You will need to get the codes checked.This will help in finding out what is causing the light to come on.Once you get the code or codes we can find out what could be causing the problem.Let me know when you get the codes and I`ll be glad to help you out.Good luck.

Posted on Mar 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bleeding the coolant system 2005 chevy uplander


Bleeding the coolant system Leisa, Check the attached links,instruction and guides on bleeding cooling systems. Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How To Fill Bleed Coolant Chevy 3 4L V6
Bleeding Air In Cooling System
Coolant Flush How to Chevrolet Uplander 2005 2008 2008 Chevrolet Uplander...
How To Bleed Cooling System EricTheCarGuy


May 21, 2016 | Cars & Trucks

1 Answer

What does it mean when my 2008 trailblazer LT stabilitrac service light comes on?


Service Stability System Message The message center displays the service stability system message when any one of many VSES-disabling DTCs is set. The EBCM sends a serial data message to the IPC requesting this display.
It means there is a problem an till you get it fixed the stability control system is disabled ! ( EBCM ) electronic brake control module Has detected a problem an set a DTC - diagnostic trouble code in it's memory an had the message displayed !
Vehicle Stability Enhancement System (VSES)
The vehicle stability enhancement system (VSES) provides added stability during aggressive maneuvers. Yaw rate is the rate of rotation about the vehicle's vertical axis. The VSES is activated when the electronic brake control module (EBCM) determines that the desired yaw rate does not match the actual yaw rate as measured by the yaw rate sensor.
The desired yaw rate is calculated by the EBCM using, primarily, the following inputs.
?€¢
The position of the steering wheel


?€¢
The speed of the vehicle


?€¢
The lateral, or sideways acceleration of the vehicle

The difference between the desired yaw rate and the actual yaw rate is the yaw rate error, which is a measurement of oversteer or understeer. When a yaw rate error is detected, the EBCM attempts to correct the vehicle's yaw motion by applying brake pressure to one or more of the wheels. The amount of brake pressure which is applied varies, depending on the correction required. The engine torque may be reduced also, if it is necessary to slow the vehicle while maintaining stability.
VSES activations generally occur in turns during aggressive driving. When braking during VSES activation, the pedal may pulsate. The brake pedal pulsates at a higher frequency during VSES activation than during ABS activation.


It

Jun 19, 2015 | 2008 Chevrolet Trailblazer

1 Answer

Message on dash reads "service stability system"


the stability system has a problem. You will have to have someone read the code to see which component is bad.

Apr 06, 2014 | 2008 Chevrolet Uplander

1 Answer

2008 chevy uplander


You should have the body computer scanned for trouble codes. A basic code reader may not access the body computer.

Jul 25, 2012 | Cars & Trucks

1 Answer

My stability system and traction control messages are flashing and my ABS light is on for my 2008 Uplander. Any suggestions why are 3 are going on?


Hello Tip.

All three systems rely on some of the same sensors in order to operate.
In this case most likely is wheel speed sensors. By far the most common problem.
The system will need to be scanned to find out which is the offending one and be repaired.
Not all scan tools have the capability to read ABS systems. Make sure whoever you take it to has this available. Most good shops will have this.
If you have further questions on this, please ask me here, be glad to help.
Thank you for using FixYa.

KL

Jan 17, 2011 | 2008 Chevrolet Uplander

2 Answers

Have 44k on a 2008 chevy uplander. Front left


I have a 2008 as well.. with 39K and the front right needed replaced.
it was covered under the 100K warranty

Mar 19, 2010 | 2008 Chevrolet Uplander

1 Answer

2008 Chevrolet Uplander. The car activates abs for no reason and records c0196 trouble code in the abs module.


• An internal fault within the yaw rate sensor/lateral accelerometer, P/N 15189628, may be the first possible cause. • The vehicle stability enhancement system (VSES) electronic brake traction control module See if this info helps

Feb 05, 2010 | 2008 Chevrolet Uplander

1 Answer

Where is the stabilizer pin for a 06' chevy uplander


no of no such part called a stabilizer pin. can you post a picture of it?

Oct 02, 2009 | 2006 Chevrolet Uplander

1 Answer

The service stability light is on


It pertains to just what it says STABILITY. Your vehicle has a system that will sense if you are coming around a curve at about 90 MPH. It will automatically apply a light amount of braking to the proper wheels, thus hopefully eliminating you and your Uplander from flying off curve. With the light on as with any warning light , you must assume whether its real or not, that the STABILITY system IS NOT operating. Significant computer / sensor diagnosis will be necessary. Hope this helps

Apr 12, 2009 | 2008 Chevrolet Uplander

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...