Question about 2006 Chevrolet Impala

Open Question

Where is the fuel filter located on a 2006 Chevy Impala SS

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
ginko
  • 19396 Answers

SOURCE: 2002 monte carlo ss

The fuel filter is located in the pressure line that runs from the fuel tank to the engine, near to the fuel tank.
Keep the engine off for few hours before replacing the filter, to get rid of some pressure in the lines.

Posted on Feb 27, 2009

Ad
Tech jk
  • 102 Answers

SOURCE: on a 2006 chevy impala it tells you to tighten the gas cap

There is no sensor for a loose gas cap. What is happening is that the evaporative emission system is sensing a "Large Leak". Usually code p0455. The computer sees this as the most probable cause is a loose gas cap depending on several factors it looks at. You would need to clear the code(s) and see if that was the problem. If the light comes back on, then you have a problem in the system that will not let it seal. Possible solenoid problem, leaking hose / line, etc.

Posted on May 08, 2009

emissionwiz
  • 76109 Answers

SOURCE: How do I program my key for my 2006 Chevy Impala?

Add Duplicate Key (PK3 or PK3+ key)
1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.
Originate New Master Key (PK3 or PK3+ key)

1. Insert new key into ignition cylinder and turn it to the ON (RUN) position.
The security light on the dash will illuminate and stay on for ten minutes.
2. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back to the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
3. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back on the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
4. After the security light has gone off the third time, the key has been programmed
into the vehicle’s computer and will operate the car. It has replaced ALL the
previous electronic key codes and is the ONLY key programmed into the
vehicle’s computer.

Add Duplicate Key (PK3 or PK3+ key)

1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.

Posted on May 20, 2009

  • 2841 Answers

SOURCE: Replace Fuel Filter on 2006 Chevy Aveo Hatchback

If the fuel filter is mounted inside the fuel tank at the pump it does not need replacing and is a permanent filter. All you have to do it follow the fuel lines from the fuel tank to the engine. If the filter is mounted in the fuel line you will find it.

Posted on Dec 10, 2009

  • 72 Answers

SOURCE: Is the serpentine belt diagram the same for a 2006

No, not even close. I have included belt routing diagrams for both. The first one should be the SS 5.3L which has a lot more pulleys.

Hope this helps. Good luck !duckfreak871.png duckfreak871_0.png

Posted on Apr 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of horn on a 2006 Chevy impala ss


Look inside the driver or passenger side benders there will be access holes you there may see where attached and plugged in.

Feb 05, 2017 | Cars & Trucks

1 Answer

Where is the can shaft located in a 2006 Chevy impala ss 5.3


the cam shafts are bolted down to the cylinder heads of any engine <shrugs>

Apr 10, 2015 | Cars & Trucks

1 Answer

Where is the fuel filter located on 2008 3.5 v6 chevy impala


Last year GM used an external fuel filter on Impala was 2005.

Feb 18, 2015 | Cars & Trucks

1 Answer

Horn relay location 2006 chevy impala ss


I think it is under the hood, in the black fuse box. If not, look in your owners manual in the fuse and fuse box section.

Jan 22, 2015 | 2006 Chevrolet Impala SS

1 Answer

2006 chevy impala ss horn relay location


Horn relay is located under the hood in power distribution centre

Jan 22, 2015 | 2006 Chevrolet Impala SS

1 Answer

Where is the fuel filter located on Chevy Impala 3.1 engine located


A 2003 Impala has a 3.4 or a 3.8 engine.
The fuel filter should be under the car in the fuel line between the tank and the engine.

Sep 22, 2012 | 2003 Chevrolet Impala

1 Answer

Is the serpentine belt diagram the same for a 2006 Chevy impala SS 5.3 as it is for a 3.9?


No, not even close. I have included belt routing diagrams for both. The first one should be the SS 5.3L which has a lot more pulleys.

Hope this helps. Good luck !duckfreak871.png duckfreak871_0.png

Apr 13, 2011 | 2006 Chevrolet Impala

1 Answer

How do i change the tail light bulb in my 2006 Chevy Impala SS


Hi, there are instructions in the owner's manual beginning on page 5-50. If you don't have a manual, you can get a free download here: http://www.extendedgmwarranty.com/owners-manual/chevrolet/2006-Chevrolet-Impala.pdf

If you need further help, please reply; and thanks for using FixYa.

Jan 16, 2011 | 2006 Chevrolet Impala

2 Answers

Were is the crank sensor located at on 2006 impala


Usually ,& depending on engine, is located on the rear side of the engine block behindthe crankshaft balancer. Good luck!

Nov 26, 2009 | 2006 Chevrolet Impala

Not finding what you are looking for?
2006 Chevrolet Impala Logo

Related Topics:

635 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...