Question about 2006 Ford Focus

Open Question

What size wrench do I need to change the battery,on a ford focus

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 98 Answers

SOURCE: ford focus 2002

The replacement bulb for the headlight in you Focus is a 9003. There are several variations to this number though. For example GE/Sylvania has a 9003CB--CB standing for "Cool Blue", 9003XV--XV standing for Xtra Vision, etc. Hopefully you plan on replacing both bulbs when you go to do so. You lights will not look like you have one old bulb and one new bulb and you won't have to worry about it going out on you at a bad time and costing you a traffic ticket. Hope this helps and have a great day!

Posted on Nov 23, 2008

Ad
KMusselmann
  • 247 Answers

SOURCE: need to know torque wrench pressure for rear wheel

Hi
it is 63 ft.lbs.
Hope this helps you
Kurt

Posted on Mar 17, 2009

  • 87 Answers

SOURCE: need size of battery for 2000 ford focus

Dependant on engine size and fuel type, any size from a 390 amp battery, if it is diesel then a 590 amp battery. No special tools needed, only a small ring spanner. Make sure yyou disconnect the earth lead first. Also you will need to enter the radio code after changing batteries

Posted on Apr 06, 2009

moparownr
  • 667 Answers

SOURCE: Waterpump belt

you have a serpentine belt, which is one belt drives all, so the routing of this belt is very specific also it matters whether or not you have a/c. Locate your belt routing chart under the hood before beginning. There is a tensioner pulley mounted on a spring arm, the spring arm should have a square drive hole in it, either 3/8" or 1/2" drive size you will need a ratchet of the proper size to insert into this square hole. Using the ratchet move the tension arm (away from belt) to loosen the belt and remove, route and install the new belt and move tensioner the same way place the belt over it and release. Hope this helps, let me know

Posted on May 23, 2009

emissionwiz
  • 76630 Answers

SOURCE: key fob not working after battery change ford focus 2006

Try reprogramming it.

1. Turn the ignition from OFF to RUN 4 times within 6 seconds.
2. Turn the ignition OFF. The system will chime to confirm programming mode.
3. Within 20 seconds, press any button on first keyless remote.
The system will chime once to confirm programming.

4. Within 20 seconds, press any button on second keyless remote.
System will chime once to confirm programming.

5. Turn ignition to RUN to exit programming mode.

Posted on May 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Size of wrench needed to change oil sensing unit in 2006 ford escape


Book and manufacturer both say it is a flat type 10 mm.

Oct 12, 2015 | 2006 Ford Escape

1 Answer

What size Allen wrench for 2001 escape front caliper?


i just changed my front rotors and pads on my 2001 escape, 6 cylinder. everyone was wrong on the wrench sizes, including the idiots at my local ford dealer. to get the brake calipers off I needed a 7mm hex bit. to get the caliper bracket off I needed an 18mm socket, it was a very easy job but check your wrench sizes first, it seems that every year and model uses different sizes.

Mar 11, 2012 | 2001 Ford Escape

1 Answer

How do you remove the starter out of a 2003 ford focus?


Removal
1. Disconnect the car's negative battery cable.
2. Raise the car's front end with its floor jack and support it on axle stands; make sure you set the parking brake first.
3. Disconnect the air cleaner's outlet tube from the throttle body if your model has an SPI engine; loosen the hose clamp with pliers.
4. Unbolt and disconnect the power-steering pump using your wrench and set the pump aside. Do not disconnect or stretch the pump's lines. This should only be needed if your Focus has a 2.3 liter engine.
5. Unscrew the starter motor's mounting bolts using the wrench and then pull the motor off the dowel sticks on the transmission housing; you might need to angle the motor to remove it. Unscrew the nuts and disconnect the motor's wiring.

Installation
1. Connect the wiring and nuts to the replacement starter motor and slide it onto the dowel sticks, then tighten the mounting bolts with the wrench.
2. Reconnect all components that were disconnected--bolt the power-steering pump in place and connect the air cleaner outlet tube using its clamp.
3. Lower the car off the axle stands and reconnect the battery cable

Mar 02, 2011 | 2003 Ford Focus

1 Answer

How do I change the coil pack in my 2005 ford taurus


Welcome to Fixya.

Here's the procedure how to replace the ignition coil pack of your car.


•1
Understand basic safety procedures. Any time you work on your Ford Focus, you should set the emergency brake and disconnect the negative, or ground, cable from the battery. Some mechanics recommend you isolate the cable to prevent accidental contact, which could spark a connection.
•2
Release the spark plug wires from the Ford Focus ignition coil pack. You may need to pinch or press a release to unlock the wires.
•3
Use a socket set or a small wrench to unbolt the ignition coil connectors. You also need to undo the capacitor electrical connectors. As you work, make note of which connectors go where--this pays off you when you reassemble the parts.
•4
Locate the bracket that holds the ignition coil pack and the electrical capacitor in place. Undo the fasteners that secure them.
•5
Separate the Ford Focus ignition coil pack from the mounting system. Replace the old Focus ignition coil pack with a new one. Verify the new ignition coil pack works with your engine, even if you use a universal ignition coil pack.
•6
Reassemble the parts. If you have a Torque wrench, use it to tighten the ignition coil bolts with 7 inch pounds of torque (10 Nm).

Thank you for using Fixya!

Nov 19, 2010 | 2005 Ford Taurus

2 Answers

What size allen wrench to remove front brake caliper


i just changed my front rotors and pads on my 2001 escape, 6 cylinder. everyone was wrong on the wrench sizes, including the idiots at my local ford dealer. to get the brake calipers off I needed a 7mm hex bit. to get the caliper bracket off I needed an 18mm socket, it was a very easy job but check your wrench sizes first, it seems that every year and model uses different sizes.

Oct 19, 2010 | 2005 Ford Escape

1 Answer

How esey is it to change the glow plugs on my ford focus.


CHANGING SPARK PLUGS EASY.ALL YOU NEED IS SPARK PLUG SOCKET.TORQUE WRENCH WOULD BE GOOD.NOT MANDATORY IF YOU MAKE SURE NOT TO OVER TIGHTEN SPARK PLUGS STRIP OUT THREAD SINCE THEY ARE ALUMINUM.YOU NEED A 3/8 RATCHET.SHORT AND LONG EXTENSION.YOU NEED SPARK PLUG GAUGE TO SET SPARK GAP.THE 2.0 OR 2.3 ENGINE SPARK PLUG GAP IS 0.041- 0.045.

May 30, 2010 | 2003 Ford Focus

1 Answer

I need to change the alternator on a 2001 ford focus and need to know what size wrench is needed to loosen the timing belt tensioner enough to remove the timing belt. Please help


I don`t know the size,but it will be metric.If you have a standard,american set of wrenches,get the one that is closest to fitting the bolt head.Here is something to help you decide what the actual metric size wrench to use.8mm is 5/16,,,10 mm is smaller than 3/8.11mm is a 7/16.12mm is larger than 7/16 but smaller than 1/2.13mm is 1/2,14mm is 9/16,15 is bigger than 9/16,but smaller than 5/8.,,5/8 is 16mm.17mm is 11/16,18mm is bigger than11/16,but smaller than3/4,19mm is 3/4.I hope this helps.

Oct 30, 2009 | Ford Focus Cars & Trucks

1 Answer

What wrench do I need to remove front calipers on a 2002 Focus?


A set of wrenches and either a c-clamp or vise grips that look like the c-clamp, and a small block of wood. You'll have to push the brake calliper piston back in.

Apr 05, 2009 | 2002 Ford SVT Focus

2 Answers

Need size of battery for 2000 ford focus


Dependant on engine size and fuel type, any size from a 390 amp battery, if it is diesel then a 590 amp battery. No special tools needed, only a small ring spanner. Make sure yyou disconnect the earth lead first. Also you will need to enter the radio code after changing batteries

Apr 05, 2009 | 2000 Ford Focus

1 Answer

Caliper wrench size for brake pads


Ford uses 14mm 12 mm 10mm

Jan 05, 2009 | 2001 Ford Focus

Not finding what you are looking for?
2006 Ford Focus Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...