Question about 2000 GMC Yukon

Open Question

Where is the heater blower motor resistor on a 1998 gmc yukon

Fan only works on high motor has been replaced with a new one

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 479 Answers

SOURCE: blower motor resistor replacement

the relays are behind the glove box. you have to take the glove box out to have access to the relay for the heating system 

Posted on Dec 10, 2008

Molson02536
  • 3854 Answers

SOURCE: where is the blower motor resistor on a '95 yukon

I am pretty sure that a 95 and 99 are the same. On a 99 Yukon the blower motor resistor pack is on top of the air box. Remove the glove compartment door, the blower itself will be on the right side. All the way to the far left on top of the air box there is a plug. Unplug and remove the 2 small screws. With some manipulation the resistor pack will lift out. Hope this helps keep me posted, be glad to help. 

Posted on Jul 04, 2009

c17hydro
  • 2984 Answers

SOURCE: how to replace the blower motor fan assembly in a

Blower Motor Removal & Installation Delphi
Blower Motor Replacement (Delphi)

1fb4643.gif
To Remove:

  1. Remove the instrument panel sound insulator panel (if equipped).
  2. Disconnect the electrical connector from the blower motor.
  3. Remove the blower motor insulating cover screws.
  4. Remove the blower motor insulating cover.
  5. Pull the retaining tab down and rotate blower motor counterclockwise to remove.
To Install:

  1. Position the blower motor and turn assembly clockwise until tab locks in place.
  2. Install the blower motor insulating cover.
  3. Connect the electrical connector to the blower motor.
  4. Install the instrument panel sound insulator panel (if equipped).

Visteon

Blower Motor Replacement (Visteon)

878e8d8.gif
To Remove:
  1. Remove the instrument panel sound insulator panel (if equipped).
  2. Disconnect the electrical connector from the blower motor.
  3. Remove the blower motor screws.
  4. Remove the blower motor from the HVAC module.
To Install:
  1. Position the blower motor and install mounting screws.
  2. Connect the electrical connector to the blower motor.
  3. Install the instrument panel sound insulator panel (if equipped).

Posted on Oct 02, 2009

ministock48
  • 258 Answers

SOURCE: 1996 GMC blower motor only works on high speed.

more than likely yes the resistor

Posted on Oct 22, 2009

  • 432 Answers

SOURCE: need to know where the heater blower motor

Unless they moved it and are still using the same part,I would say that this one is located behind the glove box sandwitched between the underside of the dash and the top of the airbox.The blower motor is mounted to the underside of the airbox.

Posted on Jan 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2001 yukon front AC fan only blows on high setting. nothing on the other fan settings.


Replace the blower motor resistor located in the blower housing under the dash on the passenger side and you will be good to go.


360dreamworx_54.gif

Aug 26, 2011 | 2001 GMC Yukon XL

1 Answer

2004 yukon xl the fan only works on high. was told it is the resistor. where is this resistor located?


the resistor is located in bottom of heater box under right side of dash it will be close to blower motor. the wires from blower motor go to resistor. check the plug and replace it as well they tend to melt

Mar 12, 2011 | 2004 GMC Yukon

1 Answer

Heater moter or fan controls not working


After checking the fuses Check the voltage at the blower motor, if you have voltage at the blower motor, replace it, if not, check voltage at the resistor. If you have voltage at the resistor but not the motor replace the resistor. If you do NOT have voltage at the resistor check the switch itself and replace as neccesary. While checking the items make sure all connections are clean, and are corrosion free.

Jan 21, 2011 | 2003 GMC Yukon

2 Answers

A/C Heater blower fan does not cycle through all speeds


Yes it is the blower Motors Resistor board. It is up behind the blower motor, just under the glove box. You have to remove the black KICK panel with its two "Push Pins" that will break too. There are 3 screws holding that resistor board in, the back two are a bear to get to. Good luck.

Feb 17, 2010 | 1998 Buick Century

1 Answer

Heater fan on 2002 Yukon does not operate in front, only rear.


The front blower motor is controlled by the blower resistor module.This is usually the problem with the front blower not working.I looked up the schecmatics and I don`t see separate fuses for the front and rear.But the fuse for the front blower is in the under hood fuse block.If this is good then The problem is probably the resistor module.It is next to the blower motor.The connector from the resistor connects to the blower motor.If you want to confirm this you can check for power and ground at the blower motor connector when you activating the blower switch on.This can be done with a test light.Make sure you have power going into the resistor module also.If you have power going in and no power at the blower motor then replace the resistor.Hope this helps.Good luck.

Dec 28, 2009 | 2002 GMC Sierra C/K1500

3 Answers

My 2000 GMC Yukon 2WD's heater fan now will only work on level 5. First level went awhile ago and every couple months since another one would go. Once level 5 is gone I aint got no heat no mo ! Help !


There is a resistor down below the blower fan on the inside firewall of the passenger side. Advance or Auto-zone carry them and they are not hard to replace or very expensive. You will have to have a small socket though. I am not sure it is a 6 or 8mm.

You will see a long plug about an inch and a half that goes into it. When they burn out you only get high as a default.

Hope this helps.

Nov 03, 2009 | 2000 GMC Yukon

2 Answers

1999 GMC Yukon - Blower only operates on high. I


on these models on the harness that plugs into the fan switch goes bad, I changed the switch and found this harness melted together on my 99 yukon

Jul 12, 2009 | 1999 GMC Yukon

3 Answers

The heater fan in my 2003 GMC Yukon XL will not turn off, even after the key is turn off, and the door is opened.


I don't know if you already fixed it, but I had the same problem on my 03 yukon, TysonRicky is right. In my case it was the blower control module. You can find it right under the glovebox. It cost me close to $100 for a new one, but very easy to replace. Can't even imagine how much it would've cost me if I had a mechanic do it.

Dec 08, 2008 | 2003 GMC Yukon XL

Not finding what you are looking for?
2000 GMC Yukon Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...