Question about 2006 Chevrolet Colorado

Open Question

How to replace 2006 chevy colorado coolant sensor

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 11 Answers

SOURCE: how to replace 2006 chevy colorado thermostat

find where top hose comes from the radiator into the engine block, then drain some of the coolant out and remove hose and thermostat from the block. remember which way the termostat sits in the block and install new one. its always a good idea to flush your cooling system before putting in a new thermostat. if the old one was plugged up, the gunk thats in your system will just plug up the new one in time too. you can get a bottle of radiator flush from most auto parts stores.

Posted on Aug 23, 2009

c17hydro
  • 2984 Answers

SOURCE: how do i change out the knock sensor on a 2006 chevy colorado

You didn't list your engine size so please pick the applicable to your motor size:

Removal & Installation 2.8L & 2.9L Engines To Remove:

  1. Lift the vehicle high enough to gain access to the knock sensor (KS) through the left front wheelhouse.
  2. Remove the left front wheel and wheelhouse liner.
Knock sensor (KS) (A), Engine harness (B), Knock sensor (KS) connector (C)


e44e83f.gif
  1. Disconnect the knock sensor (KS) connector.
  2. Detach the knock sensor (KS) from the engine block.
To Install:
  1. Attach the knock sensor (KS) to the engine block.
    • Tighten the bolt to 18 ft lbs (25 Nm).
  2. Connect the knock sensor (KS) connector.
  3. Install the left front wheelhouse liner and wheel.
  4. Fully lower the vehicle.

Posted on Sep 03, 2009

  • 83 Answers

SOURCE: coolant sensor located on a Chevy Silverado 2006

There is one for the computer and one for the gauge. One is on the intake and one screwed into the front water neck on the intake or on the water pump.

Posted on Sep 13, 2009

  • 78 Answers

SOURCE: Where is the Coolant Temperature Sensor located on

under the cylinder head on the mainblock back side

Posted on Oct 12, 2009

  • 202 Answers

SOURCE: 2006 chevy impala coolant temp sensor

The coolant temp sensor located ( below the thermostat housing in the intake manifold )

hope this can help. good luck

Posted on Mar 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced thermostate and coolant sensor now i have code po 171 too lean bank 1


the best place to start is the fuel filter and the most economical, best of luck

Nov 05, 2012 | 2006 Tracrac Chevy Colorado - Standard bed...

1 Answer

Replaced thermostate and coolant sensor now i have code po 171 to lean bank 1


You may have a engine vacuum leak, check for leaks with a bottle of propane gas and a length of rubber tube like fuel line, if you find a leak the engine idle will change. If no leaks are found the O2 sensor may be defective.

Nov 05, 2012 | 2006 Tracrac Chevy Colorado - Standard bed...

1 Answer

Colorado Transmission and high idle


The coolant temp sensor could cause the problems.
If the sensor says the coolant is 15 degrees several things would happen.
The only way to know is to be able to attack it when it happens which would be hard to predict. You could replace the sensor but may never know if it is fixed or not.
The check engine light should have come on when that code was set.

Jun 29, 2012 | 2006 Chevrolet Colorado

1 Answer

The following codes show up on my 2006 chevy colorado PO106 PO116 PO455 PO446 PO496 PO036 PO030


All these codes indicate that maybe you lost your reference signal from the computer. What someone will have to do is check fo voltage and grounds from the PCM on the coolant temp sensor, Both 02 sensor heater circuits, the evap purge solenoid and the gas tank pressure sensor. Its possble the computer failed or you poped a PCM fuse in the fuse box under the hood. The cover should have a legend to tell you which is which but I would pull all of them and inspect anyways.

Apr 20, 2010 | 2006 Chevrolet Colorado

1 Answer

How do i change out the knock sensor on a 2006 chevy colorado


You didn't list your engine size so please pick the applicable to your motor size:

Removal & Installation 2.8L & 2.9L Engines To Remove:
  1. Lift the vehicle high enough to gain access to the knock sensor (KS) through the left front wheelhouse.
  2. Remove the left front wheel and wheelhouse liner.
Knock sensor (KS) (A), Engine harness (B), Knock sensor (KS) connector (C)


e44e83f.gif
  1. Disconnect the knock sensor (KS) connector.
  2. Detach the knock sensor (KS) from the engine block.
To Install:
  1. Attach the knock sensor (KS) to the engine block.
    • Tighten the bolt to 18 ft lbs (25 Nm).
  2. Connect the knock sensor (KS) connector.
  3. Install the left front wheelhouse liner and wheel.
  4. Fully lower the vehicle.

Sep 03, 2009 | 2006 Chevrolet Colorado

2 Answers

Rough idle


I had the same exact problem on my 2004 Colorado (3.5L). Cleaned the MAF sensor (with MAF sensor cleaner) and throttle body/plate - cleared it right up.

May 10, 2009 | 2006 Chevrolet Colorado

Not finding what you are looking for?
2006 Chevrolet Colorado Logo

Related Topics:

452 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...