Question about Cars & Trucks

Open Question

Maxxforce engine electrical sensor locations

Find location of all engine electrcal sensors

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 169 Answers

SOURCE: sensor locations

air intake look at snorkel it could be part of mass air flow check intake for eng coolant

Posted on Aug 29, 2009

Ad
Smooth_Gecko
  • 125 Answers

SOURCE: check engine light code P0720...failed output

The output shaft speed sensor lets the computer know how fast you are going down the road to help it pick gear change points..
Yes, you can buy one and replace it.
First check the wires and plug going to it.
Your manual will probably describe its location better than me, but it will be toward the rear of the gearbox and usually has a small gear on the end that meshes with a mating gear on the output shaft as you put it in.

Posted on Oct 17, 2009

Testimonial: "thank you helps a lot"

bschilz
  • 2049 Answers

SOURCE: location of crank sensor 1998 jetta 2.0

It's located near the cam gear on the front of the engine however, the crank sensor, to the right of the oil filter near the bell housing is the part notorious for going out on these cars, and causing a p0322 and/or p0341 code, and sometimes others as well To replace the crank sensor you have to: Support the motor with a floor jack. Remove the starter, 2 of the starter bolts connect to the motor mount. Remove the motor mount from the frame, very easy. Remove the oil filter. That will give you just enough room to get an allen wrench in to remove the bolt holding the sensor in.

Posted on Oct 25, 2009

crapiemael
  • 241 Answers

SOURCE: p0051 code, where is the sensor located, where is

Bank 2 is passenger side, sensor 1 is the one up closest to the exhaust manifold. Plug in type (just remove old and plug back into the wiring harness connector) is about $90 at Autozone. You can get a cheaper one that you splice but it's confusing to understand which wires to splice together. Don't forget to buy the special socket, $10, to remove and install the sensor. It's split up the side for the wires. Forget trying to use an open end wrench, socket is best.

Posted on Nov 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Crankshaft sensor on a 2000nissan xterra where is it located and how can it be replaced


crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

Nov 14, 2011 | 2000 Nissan Xterra

1 Answer

Where is the tempurture cooling sensor located on a 1994 buick regal


The coolant temperature sensor is a thermistor mounted in the engine coolant stream. A thermistor is an electrical device that varies its resistance in relation to changes in temperature.

For 2.5L engines, the coolant temperature sensor is located on the left side of the cylinder head.

For MFI engines, the coolant temperature sensor is located on the intake manifold water jacket or near (or on) the thermostat housing.

zjlimited_2011.jpg

Fig. 1: Engine Coolant Temperature (ECT) sensor and connector


zjlimited_772.gif

Fig.: Engine Coolant Temperature (ECT) sensor location-3.1L (VIN T) engine shown

Hope this helps (remember to rating this and leave an testimonial comment about this free answer).

Oct 10, 2011 | 1994 Buick Regal Gran Sport

1 Answer

How do I remove the input/turbine speed sensor? I have the R/T v6 3.0L Coupe


MAKE SURE YOU IGNITION KEY OFF POSITION. YOUR VECHICLE SPEED SENSOR IS LOCATED IN THE INPUT SHAFT HOUSING NEXT TO TWO FLUID COOLING LINES TO REMOVE IT YOU REMOVE ELECTRCAL CONNECTOR FROM FROM THE VSS.THEN REMOVE THE VSS SENSOR OUT OF TRANSAXLE.REPLACE O - RING THEN INSTALL THE NEW VSS OR VECHICLE SPEED SENSOR.

Nov 25, 2010 | 2001 Dodge Stratus

2 Answers

Replacing the MAP sensor??


REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Locate the MAP sensor and remove the retaining screws
  3. Detach the electrical connector.
99e56ea.jpg

Fig. On the 3.1L engine, the MAP sensor is located alongside the intake manifold

06cd371.jpg

Fig. MAP sensor and its bracket arrangement-3.4L (VIN E) engine

c92a20a.jpg

Fig. Location of the MAP sensor on the throttle body adapter-3.4L (VIN X) Engine

ef21261.jpg

Fig. The MAP sensor is located just behind the throttle body mounting base-3.5L (VIN H) engine

c7cd8f9.jpg

Fig. MAP sensor and its location alongside the supercharger-3.8L (VIN 1) Engine

98ee1cd.jpg

Fig. On the 3.8L (VIN K) engine, the MAP sensor is located on top of the PCV valve cover
  1. Remove the vacuum hose and lift the MAP sensor from the engine.
  2. Installation is reverse of the removal procedure.

Hope helps (remember rated and comment this).

Aug 06, 2010 | 2000 Oldsmobile Intrigue

2 Answers

I need to put a crankshaft sensor but I don't Know its location I already changed the cam sensor. Ronnie


The crank sensor is located on the engine near the flywheel axis of the crankshaft.

Crankshaft Position Sensor Removal & Installation To Remove:
Location of the crankshaft position sensor on the 2.4L engine 90904g51.gif
Location of the crankshaft position sensor on the 3.0L engine 91154g20.gif
Location of the crankshaft position sensor on the 3.3L and 3.8L engines 91154g21.gif
NOTE: On the 2.4L engine, the crankshaft position sensor is mounted to the engine block behind the alternator, just above the oil filter. On the 3.0L, 3.3L and 3.8L engines, the crankshaft position sensor is mounted on the transaxle housing, above the vehicle speed sensor.
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect the crankshaft position sensor electrical connector.
  4. Unfasten the sensor mounting screw, then remove the sensor from the vehicle by pulling it straight out.
To Install:
NOTE: If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face.
  1. Install sensor and push the sensor in until contact is made. While holding the sensor in this position, install and tighten the mounting bolt to 105 in. lbs. (12 Nm).
  2. Connect the crankshaft position sensor electrical connector.
  3. Lower the vehicle.
  4. Connect the negative battery cable.
prev.gif next.gif

Jul 31, 2010 | 1996 Plymouth Grand Voyager

1 Answer

Location of cam sensor 2003 jeep grand cherokee v8


Answer
pic_12.gif
pic
REMOVAL - 4.7L
The Camshaft Position Sensor (CMP) on the 4.7L V–8 engine is bolted to the front/top of the right cylinder head (CMP Location—4.7L Engine).

It is easier to remove/install sensor from under vehicle.

Raise and support vehicle.
Disconnect electrical connector at CMP sensor (CMP Location—4.7L Engine).
Remove sensor mounting bolt (CMP Location—4.7L Engine).
Carefully twist sensor from cylinder head.
Check condition of sensor o-ring.
See picture for sensor location.


9347d80.gif

Jul 21, 2010 | 2003 Jeep Grand Cherokee

1 Answer

Were is the crankshaft position sensor located on a 2003 dodge dakota with a 4.7l engin


ANSWER: CRANKSHAFT POSITION SENSOR - 4.7L V-8 ENGINE
REMOVAL
The Crankshaft Position (CKP) sensor is located at the right-rear side of the engine cylinder block CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine the cranks sensor is positioned and bolted into a machined hole in the engine block

Disconnect CKP electrical connector at sensor.
Remove CKP mounting bolt CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine
Carefully pry sensor from cylinder block in a rocking action with two small screwdrivers.
Remove sensor from vehicle.
Check condition of sensor o-ring.
INSTALLATION
Clean out machined hole in engine block.
Apply a small amount of engine oil to sensor o-ring.
Install sensor into engine block with a slight rocking action. Do not twist sensor into position as damage to o-ring may result
CAUTION: Before tightening sensor mounting bolt, be sure sensor is completely flush to cylinder block. If sensor is not flush, damage to sensor mounting tang may result.

Install mounting bolt and tighten to 28 N·m (21 ft. lbs.) torque.
Connect electrical connector to sensor.

Jun 29, 2010 | 2003 Dodge Dakota Club Cab

1 Answer

Sensor location


The sensor is located on the engine, below the head the near the firewall. It is hard to get to! You get to it from under the car as the intake manifold totally blocks access to it from the top. The sensor causes the check engine light to come on it if the air gap between the sensor and the crankshaft becomes too great or too tight.
The Sensor itself probably is not the problem. There will be an electrical connector going into the end of the sensor and the other end goes into the engine block. It should be held in by two small screws BUT every year of Saturn engine has a slightly different (electrically and physically) Crank Angle Sensor

Nov 10, 2009 | Saturn Cars & Trucks

1 Answer

Check engine light code P0720...failed output shaft speed sensor or electrcal problem...what is a speed sensor..can i buy the part


The output shaft speed sensor lets the computer know how fast you are going down the road to help it pick gear change points..
Yes, you can buy one and replace it.
First check the wires and plug going to it.
Your manual will probably describe its location better than me, but it will be toward the rear of the gearbox and usually has a small gear on the end that meshes with a mating gear on the output shaft as you put it in.

Oct 17, 2009 | 2000 Dodge Durango

2 Answers

2005 ford excursion cam sensor location I need to change the cam sensor and the crank sensors on my excursion and i do not know where they are located


On my 02 Excursion with the 7.3L Diesel, the Cam Position Sensor is located at the front bottom of the engine on the passengers side. There is one electrical pigtail plug that is attached and one bolt holds the sensor in position. It may be located in a similar location on your 05 Ex. I do not know where the crank sensor is located. I hope this helps.

Aug 27, 2009 | 2005 Ford Excursion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

546 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14309 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...