Question about Cars & Trucks

1 Answer

95 dodge neon brake lights and rear turn signal will not work,

When the brakes are applied, the left side brake light does not work, the left rear turn signal does not work either. But the front left turn signal does work at almost 3 times the speed of normal

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 373 Answers

The fast blinking is usually a bulb burned out. Replace the rear bulbs. If this is not the problem , it may be a ground issue, but it really does sound like a bulb issue. Also inspect the light socket while you are there. Look for any bad corrosion Good luck

Posted on Jan 04, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 255 Answers

SOURCE: My brake light and turn signal on the left don't work.

Hi, you have a bad bulb,....

Posted on Aug 17, 2008

  • 1 Answer

SOURCE: Chev Cavalier 2003 only one rear turn/brake/hazard light

I have a 2002 Chev Cavalier that had the same exact problem. I replaced the bulb harness (purchased from a chevy dealership for around $5) which was fairly easy to do. I have had zero problems with it since.

Posted on Dec 03, 2008

  • 141 Answers

SOURCE: left rear turn signal and brake light dont work

You have a broken wire to the turn/brake light portion of the light as they use the same wire. Or where the plug goes into the light assy could be bad. Torsion mount lights are horrible and you should think about replacing with a universal light that you can wire direct.

Posted on Feb 17, 2009

USfalcon
  • 175 Answers

SOURCE: Brake light/turn signal no not work on left side only.

check fuse number 7 in Engine Compartment Fuse Box , if its ok you need change turn signal switch

Posted on Mar 15, 2009

  • 62 Answers

SOURCE: I have a 1998 dodge neon, the rear brake/ turn not functioning

Check all the fuses.

Posted on Aug 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

08 Buick lucerne cxl. Third brake light works as well as front signal lights. No rear brake lights or turn signals. Tail lights and headlights and third brake lights works. Bulbs good. Help


Stop Lamps
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake is applied, the BCM will then apply battery voltage to the left and right stop/turn signal lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM applies battery voltage through the signal circuit to the transmission control module (TCM) and the engine control module (ECM) indicating that the brakes are applied.
Ground for the stop lamps is supplied as follows:
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps
• G301 provides ground for the CHMSL
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.
Battery voltage from the LT TRN/SIG and RT TRN/SIG fuses located in the rear fuse block is also used by the body control module (BCM) for stop lamp operation.

Turn Signal Lamps
Battery voltage supplied to the body control module (BCM) from the fuses listed below is used for turn signal and hazard lamp operation.
• LT TRN/SIG fuse for the left turn signals
• CTSY/RF TRN fuse for the right front turn signal
• RR TRN/SIG fuse for the right rear turn signal
When the turn signal switch is place in either the LEFT or RIGHT position, ground from G300 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) to cycle the appropriate turn signal indicator ON and OFF.
Ground for the turn signal lamps is supplied as follows:
• G104 provides ground for the left and right front turn signal lamps
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps

Do you have a factory scan tool (tech2) ? Your best bet , take it to the dealer .

Sep 08, 2017 | Buick Cars & Trucks

1 Answer

Third eye works no rear signal or brake lights


The high mount brake light gets its own signal from the brake light switch (on the brake pedal). Or at least the wire leaving the brake light switch will splice, one wire to the high mount brake light, and the other for the rear brake lights is routed through the turn signal switch, and coordinated there with the turn signal wires to the rear brake lights. The brake wires and turn signal wires share the same wire, and same filament in the bulbs. It is kind of complicated, but brakes applied with no turn signal, brake light wire goes from brake light switch through the turn switch and out to the bulbs. If brakes applied with turning signal, non blinking brake light wire goes from turn switch to rear light, while the turning signal wire will go through the flasher relay, and then to the rear light to cause blinking.

I hope that makes sense. It appears the problem may be in the turn signal switch for both the turn signals and the rear brake lights.

Mar 14, 2015 | 2007 Dodge Ram 3500 Quad Cab Laramie

2 Answers

My brake light and signal light stopped working on my 1998 dodge neon on drivers side back can you help?


Does any lights on the right side work? It sounds like the ground connection to the assembly is loose.

Jan 04, 2011 | 1998 Plymouth Neon

1 Answer

1998 honda accord, with the headlights on the tail lights are on but turn signals do not work. if head lights are off turn signals work unless i apply the brake, if i apply the brake the brake lights work...


It sounds as if you have a bad earth to either one or both of your rear light clusters. If it only happens when you indicate in one direction then that is the offending side.

Nov 20, 2010 | 1998 Honda Accord

1 Answer

Jaguar xj6 break light cancels signal


Replace the turn signal switch. Bad contact inside causing a crossing of the circuits. When the turn signal is applied it should open the brake light circuit allowing for just the signal to work. Doesn't sound like the switch is doing it's job.

May 23, 2010 | 1989 Jaguar Vanden Plas

1 Answer

All lights work on the rear except the three brake lights


Sounds like the brake light switch has a problem. Located above brake pedal and activated with the brake pedal arm. Check for power going in and coming out when you apply the brake.

May 24, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...