Question about Cars & Trucks

Open Question

How to check armature status in preeti mixie chefro modle

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

LExus es 300 1998 model watter mixiing oilat engine side


You have a leaking head gasket if you are sure it is motor oil.

Jun 09, 2016 | 1998 Lexus ES 300

1 Answer

Is there a way to remove the shaft bearing from a dewalt choose with out a puller


if the bearing is on the armature shaft
pull the armature from the case and place the armature in a vise (free) with a flap bar on either side under the bearing across the jaws of the vice
use a soft hammer and hit on the end of the shaft driving the armature down and out of the bearing
get a friend to help to hold the plates and the armature

Sep 10, 2015 | Cars & Trucks

1 Answer

How do I check a 1936 Ford starter armature for shorted or open segments?


Use an ohm meter and attach one lead to the armature connection and then ground the other lead to the armature body

Sep 16, 2014 | Ford Cars & Trucks

1 Answer

Starter troubleshooting


dead spot in the armature.. check brush contacts.. clean armature contacts.. recheck if it dont run on its own.. replace it..

Dec 28, 2013 | Cars & Trucks

1 Answer

How to check a starter relay


I would be prepared to pull the starter and have it bench tested for a dry joint on one of the windings of the armature. If the armature stops spinning and this winding is under the brush there will be nothing until the armature moves until the brush can make contact with the next winding and then it will spin. The test will show if the solenoid is faulty

Dec 26, 2013 | Cars & Trucks

1 Answer

Water mixiing with oil in my 2000 gmc sierra


the most likely cause is a crack in the oil cooler in the radiator

Jul 12, 2011 | 2008 GMC Sierra 1500

1 Answer

I've taken this starter apart several times and reassembled but it spins hard and won't work. It did work but when it got hot would not start so i took it apart to check the brushes and they don't look...


The armThe armature has swelled up from age. You will need to attached it to a lathe or a drill press and file the outer armature down abot .020 of an inch. Then reinstall and try it again. When the armature swells the armature will come into contact with the fields which freezes the starter when hot. You can take a small peice of a two by four and rap the starter when its is hot and doesn't want to work before you do this proceedure to see if I am right. I know this is your problem since I used to rebuild starters for a living

Jan 29, 2011 | 1986 Ford Bronco

1 Answer

Hyundai azera how to replace brake rotors 2007 to 2009


  1. jack car up
  2. take wheels off
  3. take brake calliper off
  4. center wheel nuts will be punched in to keep it locked so you will need to lift this tab to loosen the nuts,(will require a power bar with a big pipe as they are preety tight)
  5. center nut off
  6. rotor should slide off preety easy or use a soft face hammer
This procedure is pretty common with all cars.installation is reversal of the above procedure and dont forget to lock your center wheel nut .

Sep 20, 2010 | 2009 Hyundai Azera

1 Answer

I have a 2002 grand prix gt my gas gage goes from full to emty sometimes it goes 3/4 sometimes 1/4 do u no what the problem is


sounds like you need new fuel pump. fuel pump located in gas tank. before you go buy a new fuel pump first push up and down on trunk of car real hard to try to dislodge the little armature inside of tank. this little armature is what sends the signal to the gauge telling you the quantity. push up and down on truck to try to dislodge small signal armature then check your quantity. try this when you are having the problem and i am willing to bet the little armature is stuck. the only way to fix is to buy a new pump.

Dec 29, 2009 | 2002 Pontiac Grand Prix

3 Answers

Can't find oil level stick in engine compartment 2006 bmw 525i Whould you tell me where is it?


The BMW 525I doesn't have a dip stick. The oil level is checked using the "i" menu. Select service status and from there you should choose "check engine oil level".

Jun 27, 2009 | 2007 BMW 525xi Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...