Question about 2002 Chrysler Town & Country

1 Answer

Washers blocked i have blown dirt out with airline but keeps blocking need to drain bottle is there a plug in the base

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 152 Answers

Yes there is a plug at bottom. but, you will most likly have to remove the bottle to access the plug. but if you take it to a shop that has a evacuater. they can rinse and **** out the water and repete until it is clean, and not cost that much.

Posted on Jan 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Freeze plug location


Freeze plugs are located mid way down the engine block .
Below the exhust manifolds and above the oil pan.
If you have a V shaped engine their on bolth sides of the block.
Its rare to have a problem with them unless the block freezes although they can rust out and leak.
Their like a bottle cap pushed into the side of the block to keep it from cracking if it dose freeze.
The way to replace them is to drill a large enough hole in them to pop it out with a screw driver of course after you drain the block don't let it fall into the block it could clog the system .
Once you have it out drive the new out in its tapered so its an interferance fix tape it in but don't drive it to far so it falls into the block

Mar 15, 2015 | Cars & Trucks

1 Answer

Were is the drain plug on block


You could try draining the coolant from the bottom of the radiator, rather than the block.
If you can not find a coolant release valve, try removing the hose from the lowest connection of the radiator.
Make sure that you take the cap of the expansion bottle (or radiator) to ensure that air can enter to let the coolant out.

Apr 03, 2014 | 1991 Toyota Previa

1 Answer

Driver side windsheld washer not spraying


Check the pipe feed under the hood for any kinks in the line.
Remove the pipe feed carefully and using a high pressure airline, blow back in the reverse direction of the water, back down the washer jet. This fine washer jet is prone to becoming blocked. If you don't have a high pressure airline, then you will need something very fine and flexible, yet stiff enough that when you insert it down the washer jet holes, it can disturb any blockage down there. Although I haven't tried one, you might use a yard brush nylon brush filament.

Nov 04, 2012 | Cars & Trucks

1 Answer

Washer pump working, no washer fluid reaching window, refilled washer bottle already


sounds like the water hose is kinked or the outlet ( inside the reservoir ) is blocked. also check to see if the spouts are blocked with dirt and stuff,, ( could be a blockage at the 'Y' fitting ). if you disconnect the line from the pump you should be able to blow air through to check flow to the spouts/sprayers.

c...

Dec 29, 2010 | Hyundai Santa Fe Cars & Trucks

1 Answer

Winshiled washer does not work


1. ensure that the wash fuse is ok.
2. click the ignition to on but do not start motor. and check for pump noise if not noise then suspect fuse pump, pump connection or washer switch.
3 if you can hear pump. check washer fluid bottle is not empty. check for any dirt in the bottle blocking the pump or pipe.
4 check pipes to washer jets are clear and connected.
5. check washer jets are not blocked, use a wire strand from a wire brush to clear.

is it cold? check that the fluid has not frozen in the system. get the vehicle in the warm and thaw out system once this is down top up with a good windshield antifreeze fluid.

work backwards through the sytem. disconnect water jet pipe and switch on if not fluid. move back to water container see if fluids comes or from there if so then pipes or jets are blocked.

if not pump is defective - blocked or not getting power..

i hope this was useful.

Dec 12, 2010 | 1997 Dodge Caravan

2 Answers

Were is the drain plug located on a 2007 chevy 5.3 on the passenger side of engine . is it behind the ac unit. i want to put a engine block heater in.


The block drain is on the passenger side of the engine, in the center of the block near where the oil pan attatches to the block.

Engine Block Plugs/Sensors


Engine Block Plugs/Sensors
100 - Engine Block
100 - Engine Block
101 - Oil Gallery Plug - Front
110 - O-Ring
111 - Oil Gallery Plug - Rear
112 - Oil Gallery Plug - Side
113 - Washer
114 - Engine Coolant Heater
115 - Washer
116 - Oil Gallery Plug - Side
117 - Washer
130 - Transmission Housing Locating Pin
145 - Washer
146 - Engine Block Coolant Drain Hole Plug
701 - Crankshaft Position (CKP) Sensor
702 - O-Ring
718 - Knock Sensor
718 - Knock Sensor
739 - Bolt
739 - Bolt
750 - CKP Sensor Bolt

Oct 19, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Peugeot 407 not 405 blocked windscreen washer


its in the pump it self mate ya have to take the pummp out of the bottle

Jan 17, 2010 | 2005 Peugeot 405

2 Answers

Where is the coolant drain plug on the engine block on a 1991 Civic DX?


Under the front of the car are two plastic covers to keep dirt from getting up into the engine compartment. Remove the one on the passenger side. The coolant drain plug is on that bottom corner of the radiator. It looks like a wing-nut. Please be gentle because it is just plastic and can easily brake.

Jul 23, 2009 | 1991 Honda Civic

2 Answers

WINDSCREEN WASHER FILTER IS PARTIALLY BLOCKED 1999 BMW 318 SALOON


The filter is located in the washer bottle itself. Remove the pump(pull out) from the water bottle and the filter is the black seal the pumps fits into. Pull this out and rinse.

Mar 25, 2009 | 1996 BMW 318

2 Answers

1999 renault megane sport coupe


disconnect the washer bottle plug connector. then run alive and earth wire direct from battery to washer motor to see if motor works that way, if does then new need a new washer switch on the steering column. if not then replace washer motor. should work after that unless pipes blocked.

Jan 18, 2009 | 1986 Renault Sport

Not finding what you are looking for?
2002 Chrysler Town & Country Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...