Question about 1999 Toyota Camry

1 Answer

WHERE IS THE TIMING CAM ON A 4 CYLINDER 2.2 TOYOTA CAMRY

IM TRYING TO INSTALL A TIMMING BELT

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 142 Answers

On the drives side under the covers,

Posted on Feb 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

Trying to replace broken timing belt. Trying to set #1 cyl. to TDC manually. no compression reading on 1 &4, readings on 2 & 3. What could cause this?? HELP!!


Hole in the piston crown is the worst Charles, but let's not be pessimistic :>(

More likely valves open. At TDC firing stroke both inlet and exhaust valves should be closed. The flat, low part of the cam should be on the followers. So 1 and 4 have valves open, 2 and 3 are closed. If you turn the cam 180 degrees, you should have compression on 1 and 4 and no compression on 2 and 3.

The other thing though, is that when the timing belt breaks, the valves are often in the wrong place at the wrong time and can often meet the piston head on. This can bend the valves. or damage the piston. The normal advice is to remove the cylinder head to check, and then service the valves whilst you have it apart.

A job like this, you need a workshop manual.

May 18, 2016 | 1999 Toyota Camry

2 Answers

Aligning timing belt after breakage on 1996 toyota camry 2.2 liter 4 cylinder


Dustin, The attached links will explain timing alignment on 2.2 Camry engine. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Diagram of Timing Belt Marks and Installation
work on camry engine
Aligning timing belt after breakage on 1996 toyota camry 2 2 liter 4...
DIY GEN3 Timing Belt Waterpump Oil Seal Change Part 1 Toyota Nation Forum...

May 15, 2016 | Toyota Cars & Trucks

1 Answer

How do i check the timing marks on A TOYOTA CAMRY 2 LITER 4 CYLINDER 1995 model car ?


I have attached to where you align the notch for the cam gear. The harmonic balancer has a notch on it, which you align to the "0" on the lower cover. The belt has alignment marks on them normally crank gear is the dotted line and the cam will be the solid line. Don't reuse an old timing belt of you removed it without marking it first. You should have aligned the gears to there timing spots prior to removing the belt Be very careful if you have to rotate the cam or crank the Pistons can touch the valves and cause damage. Hope this helps.
1_29_2016_12_10_45_pm.png

Jan 29, 2016 | 1995 Toyota Camry

1 Answer

I need timing belt marks for new timing belt on a 1994 Toyota Camry LE 2.2L 4 cylinder


Firstly the no.1 piston should be at TDC (compression).

The upper camshaft sprocket has a smaller hole in the web. This should be lined up exactly with the TDC timing mark behind it on the cam bearing cap. In this position it will be vertically upwards.

At the same time the notch in the crankshaft pulley timing flange should be opposite the 0 degrees mark on the timing marks on the front of the lower belt cover.

Nov 12, 2011 | 1994 Toyota Camry

1 Answer

Where are the cam timing marks on a 1997 toyota camry 4 cylinder


There is a dot on the front side of the camshaft pulley. You have to pull the top timing belt cover to see it.

Nov 23, 2010 | 1997 Toyota Camry

3 Answers

Need the timing marks of an 1989 toyota camry 4 v 2.0L


need timing marks of an 1989 toyota camry 4cyl

Aug 05, 2010 | 1989 Toyota Camry

2 Answers

Looking for timing mark's for a 1997 camry with a 2.2 4cyl motor?


Hi,


You find the timing marks on the picture below.

moz-screenshot-2.pngaab8238.jpg



Removal
Remove auxiliary 1. drive belts.
2. Support engine.
Remove:
Engine mounting and bracket.
Timing belt upper cover [1].
3.
4. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Remove:
Crankshaft pulley bolt [4].
Crankshaft pulley [5]. Use tool No.09213-60017.
5.
6. Ensure timing marks aligned [2] & [3].
7. Slacken tensioner bolt [6]. Move tensioner away from belt and lightly tighten bolt.
Remove:
Timing belt lower cover [7].
Crankshaft sprocket guide washer [9].
Timing belt.
Tensioner pulley.

Installation
Installation
1. Check tensioner pulley for smooth operation.
2. Check free length of tensioner spring is 46,0 mm [8]. Replace spring if necessary.
3. Fit tensioner and spring. Ensure spring is connected correctly.
4. tighten bolt [6].
5. Ensure timing marks aligned [2] & [3].
6. Fit timing belt. Ensure belt is taut between sprockets.
Install:
Crankshaft sprocket guide washer [9].
Timing belt lower cover [7].
Crankshaft pulley [5].
7.
8. Slacken tensioner bolt 1/2 turn [6].
9. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Turn crankshaft slowly 1 7/8 turns clockwise until crankshaft pulley timing mark [3] aligned with 45° BTDC mark [10] on
timing belt lower cover [7].
10.
11. Tighten tensioner bolt [6]. Tightening torque: 42 Nm.
12. Install components in reverse order of removal.
13. Tighten crankshaft pulley bolt [4]. Tightening torque: 108 Nm.
Manufacturer: Toyota

Jun 25, 2010 | 1997 Toyota Camry

1 Answer

Camry timing belt


Both the 2.2 Liter 4 cylinder and the 3.0 Liter V6 have a cam belt that must be replaced every 60,000 miles. The cam belt also drives the water pump and for this reason I recommend you replace the cam belt at 120,000 miles when you replace the cam belt the second time. Neither engine is an interference engine.

Jun 16, 2010 | 1995 Toyota Camry

1 Answer

Timing marks uclear 1997 toyota camry 2.2


Fist thing ... manually put crank at top dead centre number one cylinder
put socket on crank bolt , turning clock wise..
there is a mark on crank, align this with the 0 on the cover of the timming cover to crank.
trusting have aready have all timming covers of .
there is a hole at the 12 o clock postion on cam sprocket , take a light and a mirror look threw hole you should see a "u" shape mark if you can see it
it's where you want it.
as long as the mark on the crank is a "0" and the cam is at the "u"
you should be fine to take the t belt off..
loosen off tensioner , carefuly not to move crank/cam.
ones the tensioner is loose slip off belt.
reinstall new belt , make sure you replace tensioner spring , you should of got one with belt.
make sure when installing belt that the slack of the belt is on the back side
this will be taken up by the tensioner.
i hope this helps
really should have a tech do this job , if not properly timmed, coud damage engine, or run rough.
good luck.

Apr 23, 2010 | 1998 Toyota Camry

1 Answer

1998 toyota camry le 4 cylinder How do you set the


Just make sure the timing belt is on properlyy, lining up the cam and crank in proper position to each other. The engine willstart when fully assembled because the electrical has not be altered. If it has a crank position sensor , be sure to put it back on after cleaning it and the connector.

Nov 14, 2009 | 1998 Toyota Camry

Not finding what you are looking for?
1999 Toyota Camry Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...