Question about 1989 Ford F 150

Open Question

How to change oil pan gasket on ford 1989 f150

How to change the oil pan gasket on a 1989 ford f150

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
mrgreenz
  • 962 Answers

SOURCE: Changing oil pan gasket on 1989 Ford Aerostar

drain the oil from the pan and remove the filter.
Lift the car up and secure it . So it will not roll or fall. Remove the bolts from the pan using a 10 mm or so and a rachet and small extension. There are several bolts all around the pan. Remove the pan and remove the gasket. Clean up the pan and remove all gasket material from the pan. Install the new gasket around the pan and replace back.

Posted on Apr 05, 2009

Ad
  • 60 Answers

SOURCE: 1989 Ford F150 4x4 truck has oil pressure when

Problem is :1 oil viscosity 2 oil filter 3 oil sort by viscosity

Posted on Aug 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change the oil pan on a 2007 ford f150 4.2L v6?


4.2L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    WARNING
    During engine repair procedures, cleanliness is extremely important. Any foreign material, including any material created while cleaning gasket surfaces, that enters the oil passages, coolant passages or the oil pan can cause engine failure.
  2. Raise and safely support the vehicle.
  3. Remove the starter.
  4. Drain the engine oil. Install the drain plug when finished.
  5. Remove the 4 bolts and the crossmember.
  6. Remove the 3 oil pan-to-transmission bolts.
  7. Remove the 17 bolts and the oil pan.
  8. Remove and discard the oil pan rear seal.
To install:

WARNING
Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges which make leak paths. Use silicone gasket remover and a plastic scraping tool to remove all traces of old sealant. Follow the directions on the packaging.
  1. Clean the gasket mating surfaces using silicone gasket remover, a plastic scraping tool and metal surface prep. Follow the directions on the packaging.
    NOTE
    If the oil pan is not secured within 4 minutes, the sealant must be removed and the sealing areas cleaned. To clean the sealing area, use silicone gasket remover and metal surface prep. Follow the directions on the packaging. Failure to follow this procedure can cause future oil leakage.
  2. Apply silicone gasket and sealant to the oil pan sealing areas shown and install the oil pan rear seal.
  3. Apply silicone gasket and sealant to the rear main bearing cap.
  4. Install the oil pan rear seal.
  5. Apply a bead of silicone gasket and sealant to the oil pan mating surface.
  6. Position the oil pan and install the bolts. Tighten the bolts in the sequence shown. Tighten to 10 Nm (89 inch lbs.).
  7. Install the 3 oil pan-to-transmission bolts. Tighten to 34 Nm (25 ft. lbs).
  8. Install the starter.
  9. Position the crossmember and install the 4 bolts. Tighten to 90 Nm (66 ft. lbs.).


26094896-ivvnvjgd1uemkjtm4rdse3pw-2-1.gif

Feb 15, 2016 | Ford Cars & Trucks

1 Answer

How do I replace the oil pickup tube in a 1998 Ford F150?


remove oil pan unbolt pickup tube and screen from engine block an oil pump if your to replace and i would.-. prime oil pump with oil by putting in screen and turning shaft till oil comes out block side and bolt back up and install oil pan with new gasket and fill with oil and start up with idle and watch oil pressure till it comes up to normal, i would change oil filter also before starting there probly is a gasket between oil pump and block

Jun 25, 2011 | 1998 Ford F150 Regular Cab

1 Answer

Whats the easiest way to remove a oil pan for a 1989 XLT F-150 Lariat


pls specified your engine size and tranmission(2WD/4WD) ............lift the vehicle and drain engine oil, remove all bolts and be carefull for removing oil pan, oil pan gasket is reusable

Jun 26, 2010 | 1989 Ford F 150

1 Answer

How to change a oil pa non a 1990 ford f150


The pan? Or the Gasket? It is a lot of work to remove the pan, but you can replace the gasket without removing the pan.

Apr 09, 2010 | 1990 Ford F250

1 Answer

Can you replace an oil pan gasket on a 1995 Ford F150 4.9L V6 by just removing the bolts and resting it on the crossmember? I have an oil pan leak with the gasket pushed out just below the oil filter. Also...


my opinion is to do an oil change while you are at it to save some stress. draining the old oil will help from having to hold the pan full of oil and tipping it over, etc. then simply take off the bolts, which should be anywhere from8-12 or so. make sure you clean both sides of the pan. the lip and the side thats on the block. place the new gasket on the pan and put four nuts [corners are best] finger tight. then insert the rest of the bolts and make sure you dont over torque!!!

Oct 30, 2009 | 1995 Ford F150 Styleside Regular Cab

1 Answer

Changing oil pan gasket on 1989 Ford Aerostar


drain the oil from the pan and remove the filter.
Lift the car up and secure it . So it will not roll or fall. Remove the bolts from the pan using a 10 mm or so and a rachet and small extension. There are several bolts all around the pan. Remove the pan and remove the gasket. Clean up the pan and remove all gasket material from the pan. Install the new gasket around the pan and replace back.

Apr 05, 2009 | 1989 Ford Aerostar Cargo

1 Answer

Oilpan removal 1992 f-150 2wd 300 6 cyl


Do you need to remove the oil pan to change the pan or just the gasket?

Mar 02, 2009 | 1990 Ford F150

1 Answer

Oil pan gasket leak


If everything has been installed correctly and torqued right you might want to check for crackes in the block or pan.

Aug 15, 2008 | 1990 Ford F150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...