Question about 2002 Buick Rendezvous

Open Question

Head bolt torque on 1999 dodge dakota 3.9 v6 - 2002 Buick Rendezvous

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

outdoorsman5
  • 631 Answers

SOURCE: 92 buick century head bolt tighten sequence?also

Exhuast manifold torque 38 foot pounds, Head bolts are 38 Foot pounds after you add sealant to the bolts then after torque go another 130 degrees. Tighten center 4 bolts in sequence another 30 degrees. 0b61846.jpg

Posted on Nov 26, 2009

GMJunkie
  • 74 Answers

SOURCE: Need Cylinder head bolt torque specs and sequence

  1. Install the cylinder head gasket. Ensure the arrows point towards the front of the engine. The left cylinder head gasket has the letter L stamped next to the arrow.
  2. Notice
  3. This bolt is designed to permanently stretch when tightened. The correct part number fastener must be used to replace this type of fastener. Do not use a bolt that is stronger in this application. If the correct bolt is not used, the parts will not be tightened correctly. The system or the components may be damaged.

  4. Install the cylinder head.
  5. Install new cylinder head bolts. Tighten
    Tighten the cylinder head bolts to 50 N·m (37 lb ft) in sequence.
  6. Use the J 36660-A to rotate each cylinder head bolt 120 degrees in sequence. Use the J 36660-A to rotate the four center cylinder head bolts an additional 30 degrees in sequence. Refer to Notice Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

d429947.gif

Posted on Mar 10, 2010

johnjnail
  • 1702 Answers

SOURCE: head bolt torques spec

3.8L V6

cylinder head bolt torque

step 1 37 ft lbs.

step 2 an additional 130 degrees

step 3 4 center bolts an additional 30 degrees

Posted on May 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

What's the torque spec for 3.9 dakota rocker arm bolts


In the 2000 Dakota, the torque is 21 ft lb/28 N m. I suspect this torque is the same for all 3.9 L V6 engines.

Oct 01, 2012 | 1992 Dodge Dakota

1 Answer

Torque specs for 3.9l engine cylinder head and crankshaft bolts.


Page 3-26 of Chilton's reads:
14. Using no sealer whatsoever, install the new head gasket(s) to the block. Clean, dry and lightly oil all head bolts threads. Install the heads and install the head bolts.

Tighten head bolts in sequence to 50 ft. lbs. (68Nm). Repeat the sequence retightening the bolts to a final torque of 105 ft. lbs. (143 Nm) and repeat the second step to ensure that all bolts are accurately torqued.

torgue chart from chilton (page 3-11) for your engine and year show:
main bearing bolts 85 ft lbs
rod bearing bolts 45 ft lbs
crankshaft damper bolts 135 ft lbs
flywheel bolts 55 lbs

Mar 27, 2011 | 1992 Dodge Dakota

1 Answer

Where is the crankshaft sensor located on the dodge dakota 99 sport v6


On the V6 and V8 engines, the crankshaft position sensor is bolted to the cylinder block near the rear of the right cylinder head.

2e977ab.jpg

Jul 30, 2010 | 1999 Dodge Dakota

1 Answer

Head bolt torques spec


3.8L V6

cylinder head bolt torque

step 1 37 ft lbs.

step 2 an additional 130 degrees

step 3 4 center bolts an additional 30 degrees

Jul 07, 2010 | 1999 Buick LeSabre

1 Answer

Torque spec for king nut on front spindle of 1999 2 wheel drive dodge dakota?


Unsure as to what you are calling the King nut but here are the torque specs for your front end.

Steering Gear-To-Cradle Bolt...........135 ft pnds
Steering Gear-To-Crossmember Bolt (Dakota 2 WD)..........190 ft pnds
Suspension Cradle Plate To-Cradle Attaching Bolt..............123 ft pnds
Tie Rod End-To-Steering Knuckle Nut Dakota (2WD) .............65 ft pnds
Tie Rod Lock Nut.....................55 ft pnds

Dec 08, 2009 | 1999 Dodge Dakota

1 Answer

I need to seperate the engine and tranny on a 99 4x4 Dakota 3.9l. Seems to be a plate blocking access. Need to get to the torque converter bolts.


there is an inspection cover on the bottom of the bell housing you must remove to get to the torque converter bolts. you must rotate the fly wheel to access all the bolts. they make a tools for this, but a flat head screw driver works just as good, it just takes a little longer.

Oct 25, 2009 | 1999 Dodge Dakota

1 Answer

Need to the torque specs for a 1999 Dodge Durango


Head Torque sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs recheck final torque in sequence.

Torque intake manifold: Step 1: 12 inch/Lbs, (hand tight) Step 2: 72 inch/Lbs, (6) Ft/Lbs Step 3: 12 Ft/Lbs
torque intake plenum: Step 1: 24 inch/lb (hand tight) Step 2: 48 inch/lb (4) Ft/Lbs Step 3: 84 inch/lb (7) Ft/Lbs (To torque bolts, start in center using crisscross pattern)

Apr 07, 2009 | 1999 Dodge Durango

1 Answer

Need bolt torque and order for 1988 dodge heads


Torque for your bolts are 105 ft.lbs.

looking forward it would look like this for the order

7 3 1 5

8 4 2 6

Hope this helps you!!!!!

Don't forget to rate!

Mar 17, 2009 | 1988 Dodge Dakota

2 Answers

NEED TORQUE SPECS AND SEQUENCE FOR 02 DODGE 2.4 V6 STRATUS


  1. Tighten bolts in sequence shown in (Fig. 23), using the following steps and torque values:
    • Step 1: Bolts 1 - 8 to 48 Nm (35 ft. lbs.)
    • Step 2: Bolts 1 - 8 to 75 Nm (55 ft. lbs.)
    • Step 3: Bolts 1 - 8 to 75 Nm (55 ft. lbs.)
    • Step 4: Bolts 1 - 8 to +90° . Turn Do not use a torque wrench for this step.
    • Step 5: Bolts 9 - 11 to 28 Nm (250 in. lbs.)
  • I tried to send a pic of the head bolt numbers but it wont let me so e mail me dbern002@att.net have a good day DB

Feb 01, 2009 | 1997 Dodge Avenger

Not finding what you are looking for?
2002 Buick Rendezvous Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...