Question about 1998 Chevrolet C1500

1 Answer

Pulling bell/trans. off a '98 chevy 1500 but shifter nub in way

Im trying to pull off my bellhousing/trans. off the motor but the shifter nub sticks 2-3 in. above my floor board. do i drop the motor off the mounts or just undo the four bolts holding the shifter in place and take it out, if so whats the risk i run by doing that? btw its a '98 chevy 1500 2wd manuel. thanks for any help you can give me.....cole

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

You need to take the Nub out. There is not a Problem with doing this Just do not mess with the Mechanism inside the Tranny and you will be Just fine!

Posted on Jan 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Im workin on a 05 chevy blazer 4x4 ive pulled everything connect to the tranny but the transmission fluid dip stick what is keeping the tranny connected to the motor?


HAVE YOU DISCONNECTED THE TORQUE CONVERTER? SOMETIMES THE TRANS WILL BE STUCK TO THE BLOCK. YOU MAY HAVE TO TRY MOVING IT BY THE TAILSHAFT. SPRAY BLASTER (PENATRATING OIL) ON THE DOWEL PINS

Dec 18, 2014 | Cars & Trucks

1 Answer

V6 coolant leak


If it is in fact between the bellhousing and block, and not leaking down onto the outer surface of the bellhousing, its the freeze plug on the back of the block.
The engine or trans would need to be pulled to get to it.

Feb 03, 2014 | Pontiac Firebird Cars & Trucks

2 Answers

I pulled all the bellhousing bolts..motor mount bolts...and can't seperate the 4 speed granny transmission from the engine block...what's the problem..everything is lose but won't seperate..


The input shaft (on the front of the trans) is inserted into the clutch plate, so the trans has to move straight backward (or the engine has to move straight forward) about two or three inches to separate the two, before either one can move up or down.

Make sure that you can get them to rotate slightly with respect to each other, to make sure that there is not one more bolt somewhere that is still holding them together.

If you are pulling the engine, make sure that you have already removed the radiator, otherwise when you pull the engine forward, it could go too far and smash the radiator.

Oct 10, 2010 | Dodge D150 Cars & Trucks

2 Answers

98 Pontiac Trans am automatic trans...


The front of the handle has a large "U" clip. Use a screw drive and pry the clip out. It's a lot easier to do when the shifter is pulled all the way back to "1" or "2" but is doable in park still. The handle will then pull up. There will be a plastic piece in it that pushes down to release the lock in the shifter assembly. If when you push the plastic piece down it doesn't release the lock you will have to remove the shifter cover and take a look inside, to see what broke. It may require replacing the whole shifter assembly. You should be able to find the complete assembly used for fairly cheap.

Jan 02, 2010 | 1999 Pontiac Firebird

2 Answers

Go to pull starter out of engine but cant find it, I know, Im an idoit. please help


On passenger side point towards trans, next to engine block above oil pan. Has 2 bolts that screw into trans bell housing. hope this help.

Nov 23, 2009 | 1991 Chevrolet S-10

1 Answer

How to take a manual transmission out of a chevy 1500


super easy even a novice mechanic can have one out in a little over an hour, lift it in the air about as high as you can get it put jack stands under it
disconnect the drive shaft
loosen the exhaust, doesnt need to come off
remove the starter
remove the slave cylinder
remove the shifter from the top 4 screws and 4x8mm bolts and 1x10mm bolt holding the wires running to the trans.
remove the bolts that connect the motor to the trans there are 6 really that hold it with several other nuts on top holding wires and such.
remove the 4 bolts that hold the crossmember and the bolt to the trans on the crossmember,
stick your jack underneath the trans and remove the crossmember. pull the trans straight back and lower. even without the right tools you can have this done in about 30min

Oct 18, 2009 | 1999 Chevrolet C1500

1 Answer

1998 dodge ram 1500 4WD will not shift out of 2H. maybe im not shifting correctly. stick will not move at all when i try shifting. help?


The best way to do that is to start the engine put the transmittion in neutral with your foot on the brake and pull it out of 2hi,,,put the trans in park then move shifter to 4 hi or lo.

Aug 22, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

95 jeep cheorkee transmission


Bellhousing, driveshaft, crossmember yes. BUT, are we talking overdrive auto or 5 speed manual? P.S. unless you've pulled a tranny before, take it to an expert.

Jun 27, 2009 | 1994 Jeep Grand Cherokee

1 Answer

Motor swap


The flywheel is balanced different. Use the 79 flywheel. The exhaust is all going to have to be changed. The trans., bellhousing will work.

Jan 20, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Can't figure how to remove transmission


Remove shift linkage or shifter, Remove drive shaft, remove cross-member and mount, disconnect any electrical wiring and speedo cable if so equipped, Remove all bell housing bolts and slide transmission out. Use a trans jack or if you have to, 2 people can pull it by hand. Just reverse removal steps to reinstall.

Dec 27, 2008 | 1997 Chevrolet K1500

Not finding what you are looking for?
1998 Chevrolet C1500 Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6864 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...