Question about 2003 Ford Crown Victoria

Open Question

Why does my heater blows cold air on 2003 Crown Victoria

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 58 Answers

SOURCE: 2006 crown victoria - no heat

I would change the thermostat in the vehicle first and go from there. Hope this helps......Dan

Posted on Jun 21, 2008

Ad
  • 68 Answers

SOURCE: Heater blows cold air

change the heater core

Posted on Dec 21, 2008

chuck943
  • 783 Answers

SOURCE: 2006 Ford Crown Victoria HVAC only blows thru windshield defrost

You have a vacuum leak. Defrost is the default postion(no Vacuum). Start by finding the small black vacuum line near the heater hoses at the fire wall under the hood.Trace it back, it should go to a square black reservoir . Not totally sure exactly where it is located on this model,shop manual doesn't show a very good pic, but it states to remove wiper arm and pivot shaft to remove it. You will see a second line going from here to intake manifold vacuum port. Make sure you don't have a leak there somewhere.

Posted on Mar 14, 2009

97crownvic
  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

  • 290 Answers

SOURCE: 2003 Ford Exployer-Heater only blows cold air and

Sounds like a jammed air diverter gate or the coolent diverter valve. The ticking sound is the actuator trying to open the gate or the valve.

Posted on Nov 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 Crown Victoria air only blows cold even with heat on


If you put your heat control to all the way hot and the heat selection to the panel vents and there is no warm air or anything coming out at all it is more than likely that your heater core is not functioning correctly.

Nov 17, 2014 | Cars & Trucks

1 Answer

Heater blows warm at an idle but cold when driving


Does it take a long time to warm up the engine?

Apr 11, 2013 | 2002 Ford Crown Victoria

1 Answer

No hot air working with heat on only cold air blowing in my ford crown victoria


CHECK THE RADIATOR WATER. SOMETIME IT CAN ALSO MAKE A DIFFERENCE

Oct 14, 2012 | 2001 Ford Crown Victoria

1 Answer

My heat works but it is blowing any air


have your blend motor checked and you blend door

Nov 08, 2011 | 1996 Ford Crown Victoria

2 Answers

2006 crown Victoria blows hot air with the air conditioner on the air condition lines are cold under the hood


sounds like the temperature blend door is either jammed or the actuator is shorted ou. when the temperasture control is moved you should hear the door moving...my guess is you are not hearing that..the actuator would be attached to the heater plenum behind dash/glovebox area...becareful to test the correct one as there will be a fresh air actuator and a mode door actuator as well...you can determine which one is which by changing the positions on heater head from hot/col, floor/defrost, recirculate and fresh air settings..each setting will move its designated actuatror..the one not moving would be you temp actuator....have fun!

Jun 29, 2011 | 2006 Ford Crown Victoria

1 Answer

Heater blows cold air


ok so the heater draws heat from the engine and if the engine dose not heat up anuff it will only blow cold air the reason the engine may not be getting worm is because the thermostat may be stuck open

Jan 27, 2011 | 1995 Ford Crown Victoria

1 Answer

Heat goes on and turns to cold air 96 crown victoria. fixed waterpump, changed termostat, heatercore blown out twice, fluids are good. car sometimes acts like it has stored up heat, hot air will blow out...


did you buy the heater cores new heater core and radiator is two different things sounds like you thermostat is bad touch your bottom hose and your top are they both hot if ones hot and ones cold water is not circulating bad thermostat is the heater core put in right

Dec 03, 2010 | 1996 Ford Crown Victoria

1 Answer

Blows cold air out of heater ,thermostat is new


try venting the top heater hose of air,just undo the jubilee clip to expel all the trapped air.....

Oct 28, 2010 | 2006 Ford Crown Victoria

1 Answer

Heater blows cold air but sometimes will blow


Change thermostat if that doesn't solve the problem then its probaly a bad heater core

Jan 04, 2010 | 1994 Ford Crown Victoria

1 Answer

2006 crown victoria - no heat


I would change the thermostat in the vehicle first and go from there. Hope this helps......Dan

Jun 20, 2008 | 1999 Ford Crown Victoria

Not finding what you are looking for?
2003 Ford Crown Victoria Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...