Question about 2003 Ford Focus

Open Question

Windshield washer pump wont work on 2003 ford focus

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: windshield washer fluid is not being pumped out

Has it got to below freezing in your area recently? If so, your fluid is probably frozen and will need to be replaced. That is the only thing I can think of. It happened to me recently! Good luck I hope this helps

Posted on Dec 18, 2008

chrischronic
  • 235 Answers

SOURCE: windshield washer will not work even though the wipers do on a fo

check the fuse, if its ok youre gonna need a new pump.

Posted on Jan 15, 2009

godspeed808
  • 125 Answers

SOURCE: Liftgate washer problem on 2003 Ford Windstar

Yes a shop is usually great advice with this but heres some things you can do yourself. first lets keep it simple have you inspected rear nozzle and cleared nozzle openings with sharp pin?
First you must have these following tools:
haynes or chiltons repair manual
multitester with voltage and impedance features
Step one: location reservoir for washer fluid
Step two: access the sprayer motors under washer reservoir
step three: using multi tester set to 20V test hot leads to motors if theres power then move on if not check fuses and follow power leads to look for damaged power wiring
Step four: if there was power make sure the lines are intact and full of fluid after youve pressed switch (you may have to trace fliud line all the way to the rear for damage or leaks)
After all this you should've been able to find problem theres nothing left once theres power and fluid to rear nozzle except clearing the nozzle openings

Posted on Feb 06, 2009

cadman000
  • 607 Answers

SOURCE: windshield washer does not work. nothing comes out

Possibilities include a faulty washer pump / fuse , or a clog in water flow between washer fluid tank and nozzles.along with everything in between

Posted on Mar 24, 2009

01fordeb
  • 1033 Answers

SOURCE: 1998 ford expedition front windshield washer

fuse for washer pump, can you here the pump, if not then power to pump isn't present. Check the fuse for it.

Posted on Jan 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Wiper pump does not run but wipers do


Check the connector at the pump for tightness and corrosion. Check for power and ground at the connector.

Jul 03, 2015 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

How do you replace the windshield washer pump on 2008 ford focus, wipers work but no spray comes out


The hose could be clogged ! Do you know where you add the washer fluid ? Somewhere on the bottom of that plastic bottle is the washer pump .
Removal and Installation
> WARNING: Windshield washer solution contains methanol, which is poisonous. Observe all cautions and warnings indicated on label of washer solution container. Failure to follow these instructions may result in personal injury.
> CAUTION: When replacing the windshield washer pump be careful not to damage the rubber grommet.
> CAUTION: Do not operate the windshield washer pump before filling the reservoir. Failure to do so could result in premature pump failure.
  1. NOTE: When installing the reservoir, the filler neck must be lubricated using a water-based lubricant.
    Remove the bolt and the windshield washer reservoir filler neck.
  1. Remove the RH fender splash shield. For additional information, refer to Section 501-02 .
  1. Remove the foam filler and remove the retainer.
  1. Remove the 2 screws and the accessory drive splash shield.
    • To install, tighten to 5 Nm (44 lb-in).
  1. Remove the nut, 2 bolts and position the A/C accumulator aside.
    • To install, tighten to 9 Nm (80 lb-in).
  1. Unclip the A/C lines from the inner fender well.
  1. Drill out the rivet and remove the bracket.
  1. Remove the 2 bolts, slide the windshield washer reservoir assembly forward to release it, and position the washer reservoir aside.
    • Install the upper bolt followed by the lower bolt, and tighten to 5 Nm (44 lb-in).
  1. Disconnect the windshield washer tube assembly from the pump and release the windshield washer tube assembly from the washer reservoir.
  1. Disconnect the electrical connector from the windshield washer pump.
  1. Release the wiring harness from the reservoir, and remove the washer reservoir.
  1. To install, reverse the removal procedure.

Apr 07, 2015 | Ford Cars & Trucks

2 Answers

My windshield washer is not working correctly.


Assuming you have washer fluid and you can hear the pump with no flow at the main line I would guess the turbine has separated from the pump shaft.

Sep 30, 2014 | 2006 Ford Focus

1 Answer

Windshield washers won't work


it's most likely the pump that need to be replaced or the switch is broken. you can also check the fuse.

Dec 19, 2012 | 2003 Ford Expedition

2 Answers

Where is the fuse for windshield washer pump on 2002 ford focus


Hello bback.
If your wipers are working the problem is not the fuse as it is powered by the same fuse as the wipers.
It is fuse #F56 20AMP in the central junction box.
Usually the problem is a bad washer pump.
If you require further advise on this, ask me here, be glad to help.

Thank you for using FixYa.

KL

Jan 28, 2011 | 2002 Ford SVT Focus

2 Answers

Windshield washers wont work ..Can't find fuse for washers


there is no fuse the switch or washer mottor went bad pull the motor out and hook it up to a battery if it comes on its your switch if not just replace the motor

Mar 09, 2010 | 2001 Ford Focus

1 Answer

Wash wipe on a Focus 2000 model


I blieve it's the same pump taht runs the rear and front washers.

The windshield washer comprises the following parts:
  • Windshield washer reservoir, below the front left-hand fender
  • Washer pump, on the outside of the washer reservoir
  • Two washer nozzles on the hood/bonnet, adjustable.
---------------------------------------------------------
Windshield Washer Pump and Reservoir Removal
All vehicles
  1. Remove the windshield washer reservoir filler neck.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the right-hand fender splash shield (wheel shown removed for clarity).
  1. Remove the washer reservoir.
    • Disconnect the electrical connectors.
    • Pull off the hoses.
  1. Remove the windshield washer pump with rubber gasket (shown with reservoir installed).
    1. Disconnect the electrical connector.
    1. Disconnect the hoses.
    1. Lift out the pump.

Feb 27, 2009 | 2000 Ford Focus

Not finding what you are looking for?
2003 Ford Focus Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...