Question about Chevrolet Impala

Open Question

Where is the grounding wire to the PCM located for a 2006 Chevrolet Impala SS?

I need to know where the grounding wire is located for the PCM on a 2006 Chevrolet Impala SS, or what the wire is grounded to?

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 14036 Answers

SOURCE: my buick regal doesnt send signal from pcm to crank relay.

check pcm with a scanner to see if crank and cam sensor are working.

Posted on Apr 17, 2009

Ad
  • 462 Answers

SOURCE: i have a bad ground wire somwhere on my 2000 monte carlo ss

G100
Battery cable, negative cable, RH side of engine compartment to the RH frame rail
G101
Left side of the radiator support
G111
Top right of the engine, below the ignition control module
G113
Lower LF of the engine, on the automatic transaxle stud, near the starter
G151
On the left frame rail, forward of the left front strut tower
G171
On the left frame rail, right of the left front strut tower, rear of G151
G201
Behind the I/P, on the LH side of the brake pedal bracket
G202
Behind the I/P, in the center
G203
Behind the I/P in the RH side of the brake pedal bracket
G301
At the base of the LH B-pillar
G302
At the base of the RH B-pillar
G309
On the RH side B-pillar

Posted on Aug 11, 2009

  • 90 Answers

SOURCE: pcm is not grounding injectors. need a pin diagram and ground location diagram

Ground points are in different locations throughout wiring harness. If you had any work done to engine it is very possible to have missed one of the grounding eyelets during the process of putting things together. Check along wiring harness in any area you can see or reach to try to locate any loose or disconnected ground looks.

Posted on Nov 23, 2011

  • 44 Answers

SOURCE: Where are the gound wires located on a 1999 4.3 Chevrolet silverado?

From the battery to the frame. Follow it down from battery. Then there should be 1 or 2 braided lines from the frame to the body u will just have to lay down & look around

Posted on Jul 23, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Horn relay location 2006 chevy impala ss


I think it is under the hood, in the black fuse box. If not, look in your owners manual in the fuse and fuse box section.

Jan 22, 2015 | 2006 Chevrolet Impala SS

1 Answer

2006 chevy impala ss horn relay location


Horn relay is located under the hood in power distribution centre

Jan 22, 2015 | 2006 Chevrolet Impala SS

1 Answer

Where is the power control module on my 1996 ss impala


The PCM is located directly underneath the air cleaner assembly (were the air filter is housed.) I have a 96 impala too.

Jun 07, 2014 | 1996 Chevrolet Impala SS

1 Answer

Were is pcm at on 2006 cobalt ss


pcm is attached to the front side of battery box under hood, 4 10mm screws and wire connections, make sure the pcm your replacing it with is already programmed with your vin or pats will shut er down,

Aug 02, 2012 | 2006 Chevrolet Cobalt

1 Answer

How do i change the tail light bulb in my 2006 Chevy Impala SS


Hi, there are instructions in the owner's manual beginning on page 5-50. If you don't have a manual, you can get a free download here: http://www.extendedgmwarranty.com/owners-manual/chevrolet/2006-Chevrolet-Impala.pdf

If you need further help, please reply; and thanks for using FixYa.

Jan 16, 2011 | 2006 Chevrolet Impala

2 Answers

Were is the crank sensor located at on 2006 impala


Usually ,& depending on engine, is located on the rear side of the engine block behindthe crankshaft balancer. Good luck!

Nov 26, 2009 | 2006 Chevrolet Impala

1 Answer

Secondary fan on impala SS 1996 not operating. fan motor works, new sending unit, new relay installed What else could keep it from coming on?


The PCM controls these fans via certain sensor inputs, ( CTS ) and switches ( A/C compressor for instance ). When relays are removed, both relays sockets should show 12v constant ( battery voltage on "switch side" ). When the key is rolled on, there should be 12v appear in two more places, ("Coil side" ) the relays are then operated by a ground signal from the PCM. ( Powertrain Control Module ) You need a scan-tool to check for fan request, by the PCM. A/C compressor request, etc. If you have any DTC's then repairing them may well fix your problem, otherwise, you may have a faulty PCM.

Oct 22, 2009 | 1996 Chevrolet Impala SS

1 Answer

What is the code PO102 on a 2002 Chevrolet Impala


code PO102 is mass air flow sensor circuit low frequency condition.what it is saying.MAF sensor element hot wire contaminated or sensor failed.MAF sensor signal shorted to ground or grounded circuit problem.MAF sensor wiring routed close to ignition wires generator solenoids or electric motors.PCM has failed.

Jul 14, 2009 | 2002 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...