Question about Cars & Trucks

1 Answer

Tappet clearance on a renualt R5 TS - Cars & Trucks

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

What is the tappet clearance on a renault 5 ts 1985 model?

Posted on Jun 19, 2013

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Valve tappet adjustment

well, I can see ur message has been here for quite some time. Most probably you got the answer to ur request.
I just did the valve clearance on the engine of my SJ413 that has the 1000cc engine of an SJ410 :
When cold: 0.13mm Intake and 0.18mm Exhaust
Engine sounded well and worked fine after that.
Enjoy
Mehdi

Posted on Feb 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hey there I need the exhaust and Intake(valve) clearance for a komatsu 300-6 please


note Perform the valve clearance check and adjustment at the engine cold state. 1.Remove all of the ignition coils. 2.Remove the cylinder head cover.
caution Turn the crankshaft always clockwise. 3.Turn the crankshaft clockwise, and align the timing mark on the exhaust camshaft sprocket against the upper face of the cylinder head as shown in Figure. Therefore, No.1 cylinder goes to the compression top dead center. 4.Using a thickness gauge, measure the valve clearance with the arrow shown in Figure. If deviated from the standard value, make note for the valve clearance.
Standard value:

    Intake valve 0.20 ± 0.03 mm (0.008 ± 0.0012 inch)
    Exhaust valve 0.30 ± 0.03 mm (0.012 ± 0.0012 inch)
5.Turn the crankshaft clockwise 360 degrees, and put the timing mark on the exhaust camshaft sprocket in position shown in Figure. Therefore, No. 4 cylinder goes to the compression top dead center. 6.Check the valve clearance with the arrow shown in Figure. In the same procedure as 4.
7.If the valve clearance is deviated from the standard value, remove the camshaft and the valve tappet. For the camshaft removal, refer to Camshaft Removal and Installation . 8.Using a micrometer, measure the thickness of the removed valve tappet. 9.Calculate the thickness of the newly installed valve tappet through the following equation.
A: thickness of newly installed valve tappet
B: thickness of removed valve tappet
C: measured valve clearance
Equation

    Intake valve: A = B + [C - 0.20 mm (0.008 inch)]
    Exhaust valve: A = B + [C - 0.30 mm (0.012 inch)] note The valve tappet ranges 3,000 - 3,690 mm (0.1181 - 0.1453 inch) and has 47 types per 0.015 mm (0.0006 inch). The thickness below a decimal point is stamped on the reverse side of the valve tappet. 10.Install the valve tappet selected through the procedure 9, and put the camshaft in position. For the camshaft installation, refer to Camshaft Removal and Installation .
    11.After installing the timing chain, measure the valve clearance using the procedure 3 to 6. Confirm the clearance is within the standard value.
    caution Completely remove all the old FIPG, which might be remaining among the components. 12.After completely removing the liquid gasket adhering on the timing chain case, cylinder block and cylinder head, degrease them with white gasoline.
    caution The cylinder head cover should be installed within 3 minutes of applying liquid gasket.
13.Apply a 4 mm bead of liquid gasket as illustrated.
Specified sealant:
    THREE BOND 1217G or equivalent
14. Install the cylinder head cover and tighten the tightening bolts using the following procedures.
(1) Temporarily tighten to the following torque in order shown in the illustration.
Tightening torque: 3.0 ± 1.0 N·m (27 ± 8 in-lb)(2) Tighten to the specified torque in order shown in the illustration.
Specified torque: 5.5 ± 0.5 N·m (49 ± 4 in-lb)15.Install the ignition coils.

Jan 23, 2017 | Cars & Trucks

1 Answer

What are tappet clearances and sequence of adjusting on an unidentified engine?


unidentified means we can not assist you . try a local dealer

Feb 25, 2016 | Cars & Trucks

1 Answer

Petter engine tappet clearance


.010" hot inlet and .012" exhaust hot. if it is an air cooled engine go up.002" in settings.

Nov 30, 2014 | Cars & Trucks

1 Answer

Tappet clearance on a wo4d engine cant find anywhere


its in the manual and ive posted it 100 times.
here it is one more.
click the sammi icon,,,, see FSM and more.
http://www.fixkick.com/

Dec 31, 2013 | 1986 Suzuki Samurai

1 Answer

Citreon saxo 1.1cc 2002year tappet clearance


Saxo 1.1 dessire anyone no clearances on tappets mine are 0.2 front 0.4 back and won't start

Sep 06, 2012 | Mitsubishi Pickup Cars & Trucks

1 Answer

1991 Peugeot 2.5 diesel tappet clearances. Hot or cold adjustment


1991 Peugeot 2.5 diesel tappet clearances - cold adjustment !

Aug 09, 2010 | Peugeot Liberte Cars & Trucks

1 Answer

How to measure tappet clearance with dial gauge


When setting tappets, it has to be born inind that the valve stem wears an indentation into the face of the rocker. This prevents a really accurate tappet adjustment, so the customer is right again. If you do not posess a tappet setting dial gauge, a normal engineers dial gauge will do just as well. The procedure is the same as using your feeler gauge except that you set the dial gauge up on the cylinder head with the pointer resting on the head of the rocker. Press down fairly firmly on the rocker valve end and zero the gauge. Next lift up on the rocker and read off the clearance, from the gauge, Use a magnetic base to support your gauge and repeat the pocedure for each valve pair.

Mar 25, 2010 | 1988 Mitsubishi Cargo

1 Answer

WHAT IS THE TAPPET CLEARANCE FOR NISSAN GA 15 CARBURATED,INTAKE AND EXHAUST?


what is the tappet clearance setting for the ga15 nissan sunny
i need help to know the clearance of intake and the exhaust valve.

Nov 02, 2009 | Nissan Sentra Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...