Question about 1996 Ford Ranger SuperCab

1 Answer

Where is the thermostat on a 4 cylinder 96 Ford Ranger. I see a hose going to a metal tube. Is the thermostat at the end of the tube on the engine?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 367 Answers

That would be it.

Posted on Jan 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Thermastat diagram install


Thermostat - 3.0L (2V) Removal and Installation
  1. Partially drain the engine cooling system. For additional information, refer to COOLING SYSTEM DRAINING, FILLING AND BLEEDING .
  2. Remove the three thermostat housing bolts. Fig. 25: Removing Thermostat Housing Bolts
    Courtesy of FORD MOTOR CO.

  3. Remove the thermostat O-ring seal.
  4. To install, reverse the removal procedure.
Thermostat - 3.0L (4V) Removal and Installation
  1. Raise and support vehicle. For additional information, refer to JACKING & HOISTING .
  2. Remove the front splash shield. For additional information, refer to FRONT END BODY PANELS .
  3. Drain the cooling system. For additional information, refer to COOLING SYSTEM DRAINING, FILLING AND BLEEDING .
  4. Remove the cooling tube bolt. Fig. 27: Removing Cooling Tube Bolt
    Courtesy of FORD MOTOR CO.

  5. Lower the vehicle.
  6. Remove the radiator upper cooling tube bolt. Fig. 28: Removing Radiator Upper Cooling Tube Bolt
    Courtesy of FORD MOTOR CO.

  7. Disconnect the upper radiator hose and engine vent hose. Fig. 29: Disconnecting Upper Radiator Hose And Engine Vent Hose
    Courtesy of FORD MOTOR CO.

  8. Remove the two bolts, and separate the radiator tube from the thermostat housing. Remove the thermostat. Fig. 30: Removing Bolts And Separating Radiator Tube From Thermostat Housing
    Courtesy of FORD MOTOR CO.

  9. To install, reverse the removal procedure.

Apr 22, 2012 | 2002 Ford Taurus

2 Answers

LOCATION OF THERMOSTAT


It is on the front of the engine, follow the upper radiator hose to the engine block. On a 4 cylinder engine it's located on the front of the engine block. On the 6 cylinder engine, it's located near the front of the intake manifold. There should be three bolts, remove and thermostat should be underneath. pay attention to the way it was installed.

Feb 28, 2011 | 1998 Ford Ranger SuperCab

1 Answer

How do i replace a thermostat on a 96 nissan xe pickup?


It is located at the enine end of the lower radiator hose inside the metal piece atttached to the engine. the metal piece has 3 bolts to take off that attach it to the engine. I took off the fan and fan shroud for easy access. this is fora 95 xe 4 cylinder.

Dec 11, 2010 | 1996 Nissan Pickup

2 Answers

Leak from 2001 Ford ranger Water Intake Manifold - There is an aluminum part coming out of the manifold on top of the engine that is leaking. It is not on the rubber hose but on the metal part that...


The piece you are describing sounds like the thermostat housing. These housings are normally bolted to the manifold, so you can simply unbolt it. If it is cracked, you will need to replace it. If it is not, you can replace the gasket underneath it and reinstall it.

May 15, 2010 | 2001 Ford Ranger Regular Cab

1 Answer

98 ford ranger 4 cylinder. What is the trick to remove the thermostat housing in order to replace the thermostat? THANKS


Just did this today on my 2000 4 cyl. It was a pain.

First off drain the radiator. There is a piece that sticks out at the bottom on the radiator on the drivers side. Put a large container under it and unscrew the white-ish plastic bolt to release the fluid. Make sure the radiator cap is opened to let it drain quicker. Then remove the top hose. The thermostat housing is at the end of the radiator hose on the engine. There is a bolt on the upper right, right up against the belt shroud for the camshaft. There is one more under the housing to the left. You pretty much have to feel for it. There is not much space to work with so I removed the fan (4 bolts) wiggle it off. To remove the fan you also have to remove the shroud to get it off. No problem just two bolts. This should give you plenty of room to work with. Then remove the housing and exchange parts. Replace the gasket (its a small rubber o ring. Mine looked fine so I left it, but I did put a bead of silicon around it just in case. Reverse the steps and add fluid back to the system.

Jan 19, 2009 | 1998 Ford Ranger SuperCab

1 Answer

Replace thermostat in 2000 ford ranger


the open pipe that you took the hose off of is the thermostat housing, you will need to remove this to reveal the thermostat, make sure you use a new gasket with sealant when reinstalling thermostat housing to prevent leaks and dont over tighten the bolts,run both bolts down as far as you can before final tightning

Dec 26, 2008 | 2000 Ford Ranger SuperCab

1 Answer

2000 Ranger 4 cyl auto w/ac, no heat, temp guage doesn't move


follow the upper radiator hose to ehrer it connects to the engine, the t-stat is right there
olso remove all that other stuff in needed

Dec 16, 2008 | 2000 Ford Ranger SuperCab

1 Answer

1995 Ford Ranger ( engine light ) and stuff need help plz


if your obd2 scanner fits the connection you have obd2, obd1 connector is way differnt.

your code p1443
Control System
Canister Purge
Valve (Mechanical)
Malfunction
Monitors the fuel vapor
flow between the
engine intake manifold
and the EVAP
canister. The system
failure occurs when a
leak or blockage
between the intake
manifold, the EVAP
canister purge valve
and the EVAP canister
is detected by the
PCM.
l Pinched, blocked or
plugged fuel vapor
tubes/hoses (except
between fuel tank and
EVAP canister)
l Damaged EVAP
canister
l Disconnected, cracked
or cut fuel vapor
tubes/hoses (except
between fuel tank and
EVAP canister)
l Damaged EVAP
canister purge valve
Check for audible vacuum
noise in the engine
compartment or significant
fuel odor in the engine
compartment or near the
EVAP canister.

This link has all the codes you need.
http://rockledge.home.comcast.net/~rockledge/RangerPictureGallery/DTCs.pdf

Jul 17, 2008 | 1995 Ford Ranger Supercab

1 Answer

Charging the Air Conditioner


You'll need the hose and cans of air. On the passenger side under the hood, there is a black cylinder tank with a metal tube and black cap. Remove the cap, attach your hose and canned air and follow the directions on the can. Should say something to the effect of shake can well before use, attach hose to can, twist the lever to break the can's seal, reverse the lever to allow the air flow, attach to vehicle, hold can upright, rotate can from the 12 oclock position to the 3 oclock position every few seconds until the can is empty or your cylinder will not take any more.

Jun 05, 2008 | 2006 Ford Ranger

Not finding what you are looking for?
1996 Ford Ranger SuperCab Logo

Related Topics:

237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...