Question about 1998 Mercury Villager

Open Question

1997 Mercury villager dash lights power windows and power door lock s all stoped working at same time . Drivers window went downabout three inche

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: drivers power window went down

Had the same problem with mine, Removed the door panel and removed the window motor( two bolts holding it in), reconnected the window switch and ran /tested the motor. If it runs reinstall the motor and it should go up and down now. I had 2 windows jam down and this fixed both of them

Posted on Jul 23, 2008

Ad
arenee08
  • 1 Answer

SOURCE: 1995 mercury sable...tail lights, dome

you might need a new battery or you could possibly have a ground problem...check the connections to your battery, you may need to fix the cables. i had that problem with my 1996 sable.

Posted on Nov 18, 2008

  • 512 Answers

SOURCE: 2000 mercury mountaineer power windows won't work

check for a broken wire in the wiring between the body and door

Posted on Nov 30, 2008

richrobi
  • 15 Answers

SOURCE: power windows wont work

All things Capri are at //www.techcapri.com/
The manuals are there - check them out ...
Wiring diagrams are there. Probably fixed by now anyway.

Regards
Richrobi

Posted on Jan 07, 2009

emissionwiz
  • 79851 Answers

SOURCE: speedometer quit working

this car uses an electronic speedo head, u must rmove the speedometer from the dash and send it in for repair at an authorized ford electronics repair center.

Posted on Jan 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

Intermittant Electrical Tip for 1997 Villager


I am not 100% sure of this fix for all Villagers, but, I had for sometime a sometimes intermittant electrical problem it would come and go with no particular method to its madness, it effected various components in the Van, one day it might be my wipers door locks, or windows etc. even the starting system, then one day I got what looked like a complete disconnect from the electrical systems, nothing worked , no lights, no horn, no clicking relays, no dash lights, no power to the fuses, no ignition switch nada, as it turns out there in a part of the Positive post that has a Red protective cap over the post, with wires coming out of it, well it appears that it can develope a disconnect to a point where no current passes through it and it is quite invisable to the naked eye, I took the Red cover apart conected it directly to the bolt on the POSitive post and everything started working and knock on wood its been two weeks without a problem, just thought I would toss that out there.

Thanks
watcher248

on Oct 04, 2009 | 2002 Mercury Villager

1 Answer

None of my power windows work on my 99 Villager.


make sure you did not accidently hit the lock out switch on driver door controls for windows. Relay is behind fuse panel.

go to villager quest yahoo group for much morehelp

gerry

Aug 03, 2011 | 1999 Mercury Villager

1 Answer

1997 mercury villager passenger side mirror replacement guide. how do i do it? is there an easy access panel or does the whole door panel need to be removed


door panel must come off.

go here for villager help

http://groups.yahoo.com/group/villagerquest/

Section 01-05: Trim, Interior 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door
Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. svv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel.
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screw from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure. Body Side
Removal
  1. Gently pry loose the body side door latch handle bezel and remove it.
  1. Slide a suitable tool behind each of the retainers and twist the tool to disengage the body side door trim panel from the body side door (24622).




Installation
To install, reverse the removal procedure. Door Electrical Connections
Removal and Installation
Refer to Section 01-11 for Power Window, Section 01-09 for Power Mirror, or Section 01-14B for Power Locks. Watershield
Removal
  1. Remove the Front Door Trim Panel . Refer to the removal procedure in this section.
  1. Remove the front door watershield by carefully detaching it from the adhesive.
Installation
  1. Install the front door watershield in the proper position and press firmly at the adhesive areas. If necessary, use additional adhesive to ensure an adequate seal.
  1. Install the Front Door Trim Panel . Refer to the installation procedure in this section.

May 22, 2010 | 1998 Mercury Villager

1 Answer

1997 villager just started locking the doors automatically


This is a common issue. You have poorly adjusted inside lock rods, or water in your door lock actuator connector behind the door trim panel , or you need to cut one wire in the driver door wire harness to defeat the autolock function. Go here for info on what to do. See files and also links for this issue. http://autos.groups.yahoo.com/group/villagerquest/

Jun 05, 2009 | 1997 Mercury Villager

Not finding what you are looking for?
1998 Mercury Villager Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

fordexpert

Level 3 Expert

5685 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...