Question about Cars & Trucks

Open Question

How to remove a 2001 ford ranger rearend pinion bearing

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 512 Answers

SOURCE: Pinion Bearing

the only way to replace pinion bearings is to remove the differential. you shouldnt have to remove the bearing to replace the seal

Posted on Nov 18, 2008

chuck943
  • 783 Answers

SOURCE: torque specs 7.5 inch rear axle 96 ford ranger

Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

Posted on Jan 30, 2009

emissionwiz
  • 75807 Answers

SOURCE: 89 Ford Ranger Carrier bearing

All the bearings for the rear diff are pressed off and on, they can be done at home if u have a high quality bearing puller, but to press them on should be done at the machine shop.

Posted on Feb 09, 2009

csmock132
  • 4669 Answers

SOURCE: Clutch release bearing removal

You have the transmission out and are trying to remove it from the slave cylinder right? Just pull straight out. It should pop free. It just has plastic tabs that hold it on.

Posted on May 30, 2009

  • 12104 Answers

SOURCE: how to remove bearings on 1998 gmc jimmy axle

if diying and axle bad replace the whole unit from salvage or rebuild shop.if changing the bearings its a lot of work and you will need some special tools to put back together .first you need to use a lift or again have to remove unit from truck, disconnect battery remove drive shaft,remove pinion nut need large breaker bar loosen bolts to rear cover drain fluid remove cover have someone push axles toward center remove c locks slide out axles best way to remove bearings is slide hammer bearing removal unit remove rear [gears] dont loose shims will see pinion bearing bearing remove and replace now 2 put it back.need shim package, red lead, 4 ring and gear mesh adjustments ,,

Posted on Sep 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gmc safari 2001 replaced rearend because. It exploded now the oil gear is fluctuating when idle and the van is shaking while idle. Rearend. Is hot to touch and i hear popping. Noise when i cut it off


The rear end will be to hot to touch after driving but if it is really hot (like cannot get the finger anywhere near it )then the problem will be in the diff . Possible pin ion bearings are under excessive preload by nut using a new spacer under the pinion flange or attempting to remove back lash at the pinion flange by tightening up the pinion nut. Excessive oil and the wrong grade of oil ( ordinary diff oil in a LSD diff) or running one side tyre at a different profile height to the other. The popping noise may be oil burning off ( like fat in an overheated fry pan)

May 07, 2014 | Cars & Trucks

1 Answer

How do you remove the front rearend crown and pinion on 1997 gmc serria 4x4 1500 pick-up


That indicates a bad pinion bearing. On this rear end it is usually necessary to replace the ring and pinion gears as well as the bearings becasue when the pinion bearing goes bad it will spin on the pinion gear itself causing it to wear thus just replacing the bearing will not work because it will fit loose on the pinion gear and it needs to be pressed on tight. ---------- First the c-clips are to be removed from the pinion gears.-------- Click this link below and follow the detailed procedure:---- http://technoanswers.blogspot.com/2011/07/how-to-remove-rear-end-crown-and-pinion.html -------------- This should help.Thanks.Helpmech.

Jul 17, 2011 | GMC Sierra 1500 Cars & Trucks

1 Answer

I need to know how to get the hex nut out of my 1993 ford Ranger pickup-rear end ??


Caution!!! Removing the driveshaft yoke retaining nut could cause misalignment of the ring and pinion gears and lead to more serious problems. If you are wanting to access the pinion bearing because your 8.8 rear end has started making noise then you really need to disassemble the unit as a whole. A job left in most cases to an expert.

Apr 10, 2011 | 1993 Ford Ranger SuperCab

1 Answer

I have a whining noise in the differential of a 1998 ford explorer. There isn't any play from side to side. Can this rearend be shimmed?


You probably are having pinion bearing problems. It seems that ford had some rearend problems with some of there trucks and suv's.

Nov 08, 2010 | 1998 Ford Explorer

1 Answer

Extra play in rearend when driving, what causes this?


Loose pinion gear right where the drive shaft bolts up.

Nov 02, 2010 | 2004 Ford Ranger

2 Answers

I have a Ford Mustang GT 2003 that has a bad roaring sound in the rearend. What might be the problem?


have your rear brakes checked and your diferential fluid it might also be a rear bearing hope this helps

Dec 11, 2009 | 2003 Ford Mustang

1 Answer

'95 Ford Bronco full size I dropped the rear


Normally when you take driveshaft off, you'll see a big nut in behind it, that attaches yolk to differential. Remove that big nut, and it should come out, but may need a puller. It's splined, and should be a bearing in housing,yolk.

Dec 04, 2009 | 1995 Ford Bronco

1 Answer

Need 2 get axels out of ford 8.8 rearend. I got it all apart but i cant get the axels to come out. I need to replace the axel seal and bearing. Hope you can help.


Do you have the pin in the differential out & "c" clips removed, or is it a different system? Once pin is out you push in slightly on axles & remove "c" clip, then pull them out.

Apr 26, 2009 | 1992 Ford Ranger

1 Answer

Rear end spitting gear oil out the yoke is this a simple pinion bearing problem. Just bought the truck and when I took it down the road for the first time I found problem by loud gurring sound coming from...


Sounds like the pinion bearing is shot, and its not a easy fix, as the rearend has to be taken apart to replace the bearing. Unless you have done one before and you got all the tools and a dial indicator to set everything back up to specks, its best to have a shop thats done this kind of job before to do it for you. In the long run its the cheapest way out.

Apr 01, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

Torque specs 7.5 inch rear axle 96 ford ranger


Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

Jan 30, 2009 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...