Question about Cars & Trucks

Open Question

2010 chevy cobalt how to remove radiator

I need to know how to remove a rad on a 2010 chevy cobalt

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
r_mcalhoun
  • 166 Answers

SOURCE: what is the time they pay to change radiator support in 06 cobalt

3.0 hours

Posted on Apr 24, 2009

Ad
  • 10 Answers

SOURCE: I need to remove the front headrest of a 2008 chevy cobalt lt

Push the button and pull up on it at the same time

Posted on May 25, 2009

  • 20 Answers

SOURCE: My 1998 Chevy Silverado has coolant leaking from

There's not usually a seal for these, the metal is commonly molded into the plastic sides of the radiator.. Remove the radiator tube and inspect the plastic around the fitting for cracks. If you find cracks in the plastic, then you know your answer. If it's leaking from around the radiator hose you could try replacing the clamp with a hose clamp that you can tighten with a screw driver.

My guess is the plastic is cracked there, and the radiator needs replaced, but you should inspect it first of course.

Good luck

Posted on May 09, 2010

  • 2926 Answers

SOURCE: Chevy Cobalt Jump Start -

You do need to connect the ground lead to the battery. Connect the positive lead to the battery post, then connect the ground lead to metal bracket or chassis nut on the colt bolt. Then connect the positive to the other car and negative to the other car. Keep in mind, always connect the positive first and disconnect the positive last.

Posted on Nov 26, 2010

dttech
  • 4803 Answers

SOURCE: 2010 cobalt need 2 know

The low tire pressure warning should go out if you set all of the tire pressures to the correct pressure, then drive the vehicle for about a mile. You should not have to "relearn" the Tire Pressure Monitoring System (TPMS) unless the tires are (A.) rotated into different positions or (B.) There is a bad sensor that needs to be replaced.

For more information, you can read the information in your Owner's Manual. Here is a link to a pdf version 2009 Cobalt owners manual. (The information and procedures are the same for 2008 - 2010 Cobalts) The TPMS section starts on page 5-64

Cobalt Owner's Manual

Posted on Mar 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Towing capacity of 2010 chevy cobalt


Should not tow any amount with a cobalt not recommended

Mar 05, 2015 | 2010 Chevrolet Cobalt LS

1 Answer

How do I replace the shifter light in 2010 cobalt


Sadly you must remove console entirely . Start by open storage bin if equipped -- find screws /bolts remove then search for any others .. gently pry upwards -- may need to remove more this will give visual of wires to light etc. good luck .

Nov 27, 2014 | 2010 Chevrolet Cobalt

1 Answer

2010 chevy cobalt issues.Engine light comes on/off all the time.reset by removal of battery cable.I tune the car up by changing the spark plugs/boots properly with dielectric grease etc.Car ran fine o


Advance Auto will read your codes for free and give you a print out of codes. This will save you $100 and a lot of guess work. I know MAF, MAP and PCM sensors are common problems on these.

Nov 22, 2014 | 2010 Chevrolet Cobalt LS

1 Answer

2010 chevy cobalt engine light on with code po641?


its the 5 volt reference user ecu need a expert to diagnostic this problem

Sep 23, 2014 | 2010 Chevrolet Cobalt

1 Answer

I HAVE 2007 CHEVY COBALT MY CAR TAKES LOG TO GO IN DRIVE AND I CUTS OFF IF I SLOW DOWN


bring in your vehicle to get the transmission filter changed and the cooling rad (lower part) flushed out. that should fix your problem.

Jan 15, 2014 | 2007 Chevrolet Chevrolet Cobalt LS

1 Answer

My 1998 Chevy Silverado has coolant leaking from the radiator at the small metal fitting at the top drivers side of the rad. Is the a seal that can be replaced or does the entire rad need to be replaced?


There's not usually a seal for these, the metal is commonly molded into the plastic sides of the radiator.. Remove the radiator tube and inspect the plastic around the fitting for cracks. If you find cracks in the plastic, then you know your answer. If it's leaking from around the radiator hose you could try replacing the clamp with a hose clamp that you can tighten with a screw driver.

My guess is the plastic is cracked there, and the radiator needs replaced, but you should inspect it first of course.

Good luck

May 09, 2010 | 1998 Chevrolet C1500

2 Answers

What all do i have to do to drain radiator in chevy 2004 silverado 1500


eithor open rad reain in bottom of rad or remove lower rad hose both will drain rad

Jan 07, 2010 | 1999 Chevrolet K1500

1 Answer

Need help to change thermostat in 1998 Chevy 2500 pick up


the rad cap is on the top of the radiator on the passenger side,as for the thermostat....locate the upper rad hose(comes out of the top of the rad aprox 3" wide) it should be on the driver side of the rad. Follow the upper rad hose from the rad to the engine,the housing for the thermostat is at the end of the hose.
1:drain the radiator(there is a drain **** at the bottom of the radiator protrudes from rad looks similar to a wing nut)
2:Remove the two bolts in the thermostat housing(there may be some nuts holding some ground wires there that you have to remove before you can remove the thermostat housing bolts)
3:remove the housing ...........note: make note of the position of the thermostat before removal.
4:clean gasket surfaces install new gasket \ silicone (automotive grade silicone can be used with or without gasket) 5:insert new thermostat in the proper position.
6:replace housing and hose and top up the rad
hope this helps.......Thanks for choosing FIX YA!

Jan 03, 2009 | 1998 Chevrolet C2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...