Question about 2003 Chevrolet Venture Passanger
3400 SFI engine
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
99 chevy malibu v6 3.1 engine, head bolt torque is-- 98 through 2001 is step1- 37 foot lbs, step 2- rotate an additional 90 degrees (1/4 turn). the rocker arm bolts are 168-in. lbs.
Posted on Sep 07, 2010
Step one 37 ft lbs then tignten 120 degrees more
Step one 11 ft lbs then tighten 90 degresss more
89 inch lbs
132 inch lbs
Posted on Dec 02, 2008
There are two different torque specs for this engine depending on which bolts you are torquing. This engine uses three different length bolts, the two sets of longer bolts can be torqued to 70 foot pounds, the short set of bolts that go along the bottom of the head should be torqued to 65 foot pounds. Head surface and block surface should be clean, straight and the a new head gasket should be used.
An easy way to guide yourself in the proper sequence is to make a cheat sheet of sorts. Take the headgasket and piece of cardboard about the same size. Using the headgasket as a template, mark each of the bolt holes on the cardboard with a sharpee marker, pencil or pen. Also outline the headgasket and mark the top of your drawing. Now starting from the center bolt as number 1, move either to the right or left, up or down to the next bolt hole and mark that as number 2. Now move to the bolt hole diagonally across from number 2, past Number 1 and mark it as number 3. Continue this sequence of moving diagonally back and forth across the headgasket outline until all of the bolt holes are marked with a number. What you are trying to do is start at the center of the head tightening it down in steps of about 15 foot pounds moving out from the center.
I have built a lot of these engines over the years and they are very forgiving of the head torquing sequence. As long as you start at the center and move out left and right, up and down alternating back and forth, you will have no problems. As a final check once you are done, check the torque on each head bolt to make sure you have not missed one. This does not have to be done in any sequence and you will then be sure that you have it completed properly. Good luck.
Posted on Apr 27, 2010
Tips for a great answer:
Nov 29, 2015 | Cars & Trucks
Sep 04, 2014 | Chevrolet Venture Cars & Trucks
Sep 19, 2013 | 1996 Saturn SL
Jun 18, 2011 | 1998 Buick LeSabre
Fig.: Cylinder head bolt torque sequence-2.2L engine
Apply a coating of 1052080 or equivalent sealer to the cylinder head bolt threads. Install the cylinder head bolts (within 15 minutes of sealer application), then tighten them in the proper sequence first to a torque of 46 ft. lbs. (63 Nm) for long bolts or to 43 ft. lbs. (58 Nm) for short bolts and then tighten all bolts an additional 90 degree turn using a torque angle meter.
Hope this helps (remember to rate this answer).
Jan 25, 2011 | 1996 Isuzu Hombre
Nov 16, 2010 | 1997 Chevrolet Cavalier
Aug 02, 2010 | 2004 Dodge Stratus
Jul 15, 2010 | 1996 Chevrolet Cavalier
May 12, 2010 | 1998 Toyota Sienna
Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme
195 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: