Question about 2002 Chevrolet Cavalier Coupe

1 Answer

Cluster not working, engine light working

Car starts and everything working except instrument cluster. Engine light on when ignition is on, goes off when starting. all fuses ok. Ed Swanson e-mail: twofer@bellsouth.net 404-405-2587

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,101 Answers

It is a common problem with GM cars and trucks after 2000. I have 5 cavaliers in my shop this week with the same problems. it is cheap to get other one from the junk yard

Posted on Jan 03, 2013

  • 2 more comments 
  • edward a. swanson Jan 05, 2013

    FixYa/Teds repair: Told you I would get back. Got a replacement Instrument Cluster on line with a Junk yard in contruction with Jones boro Auto Parts. Hooked it up, andworks fine. Cannot thank you enough for your advice and encouragement.

  • edward a. swanson Jan 05, 2013

    Cost: $50.00

  • edward a. swanson Jan 05, 2013

    Olease let me know you got this reply.

  • teds repairs
    teds repairs Jan 06, 2013

    hi sorry I was on the road . I am a self employed mechanic. I am on facebookhttps://www.facebook.com/TedsRepairs

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 BMW 318i SE dashboard dead except from handbrake and airbag warning light


Have you checked the dash dimmer switch to see if it's on fully?

Jan 08, 2018 | BMW Cars & Trucks

1 Answer

1996 Ford Escort 1.6 Zetec, dash warning lights stay on dim even with ignition off. Light up normally when.ignition is on but no starter at-all. Plug in OBD11 tool and everything works fine


OBD11 tool and everything works fine ??? That'sjust for the engine computer ! Need a professional type scan tool to view instrument cluster data . The instrument cluster has a microprocessor inside an can set DTC'S - diagnostic trouble codes , separate from OBD2 . A bad cluster could bring down the Serial data network causing all kind of problems . Do you know what a data network is ? Your ford has SCP network .
Communications Network Information Module

Mar 27, 2017 | Ford Cars & Trucks

2 Answers

When I start my 2004 Mercury Mountaineer the check engine light flashes the battery light comes on and won't turn off the oil gauge seems to be rising in the battery gauge seems to be going lower.


Probably,factory installed alternator has failed and vehivle is only using battery power.Suggestion:Start engine and check available voltage at battery with DVOM.SHOULD be 13.9 volts minimum and about 14.5 max.if not in range listed.please have alternator checked for failure.

Apr 21, 2016 | Mercury Cars & Trucks

1 Answer

I have a 2001 mustang bullitt that is showing service engine light on. Took it to mechanic and he put 2 different machines on it to show code for problem. No codes coming up and he can't turn off the...


There is a diagnostic procedure in the factory service repair manual for engine light lit ,no codes . Did you take it to ford dealer ? MIL - is referring to check engine , service engine soon etc...
  • MIL always on when engine is running (no DTCs):
  • MIL circuits
  • For Focus, Mustang, Town Car, Continental, LS6/LS8, Escape, Windstar, F-150, Expedition and Navigator/Blackwood:
  • Instrument Cluster, Section 413-01 of the Workshop Manual.
  • All Others:
  • GO to NB1

SERVICE ENGINE SOON indicator After the engine is started, the SERVICE ENGINE SOON indicator will prove out for a duration of three seconds. If the instrument cluster does not receive a message from the PCM within five seconds, the instrument cluster will illuminate the SERVICE ENGINE SOON indicator and log a diagnostic trouble code (DTC).

  • An indicator is inoperative/always on - SERVICE ENGINE SOON
  • Circuitry.
  • Bulb.
  • Instrument cluster.
  • PCM.
  • GO to Pinpoint Test P .

PINPOINT TEST P: AN INDICATOR IS INOPERATIVE/ALWAYS ON - SERVICE ENGINE SOON CONDITIONS DETAILS/RESULTS/ACTIONS P1 CARRY OUT THE INSTRUMENT CLUSTER SERVICE ENGINE SOON INDICATOR ACTIVE COMMAND Trigger the HEC active command MIL.
  • Did the SERVICE ENGINE SOON indicator illuminate?
Yes REFER to Powertrain Control/Emissions Diagnosis (PC/ED) manual.

No INSTALL a new instrument cluster; REFER to Instrument Cluster . CLEAR the DTCs. REPEAT the self-test.

Jul 18, 2017 | 2001 Ford Mustang

1 Answer

2001 cadillac dts..... My cluster wont stay on.. I turn the key on and it lights up as if it was gonna work.. As soon as I start the car it goes off and its all black. Nothing works except check engine...


You are having a Battery Issue or a Charging Issue. When you crank the engine over, the Draw of POWER is shutting down the Instrument Cluster. Fix the Charging Problem and then see what you have...

Apr 08, 2013 | Cars & Trucks

1 Answer

Have code 0463 fuel levelcircut input high what do I look for


There is no module under the dash on your vehicle .
P0463 - Fuel Level Sensor A Circuit High Description: The powertrain control module (PCM) monitors the fuel level input (FLI) circuit for electrical failure. The test fails when the signal moves above the maximum allowable calibrated parameter for a specified fuel fill percentage in the fuel tank. Possible Causes:
  • Fuel pump (FP) module concern
  • Incorrectly installed fuel gauge
  • Damaged instrument cluster
  • FLI shorted to VPWR
  • CASE GND circuit open
  • Overfilled fuel tank
  • Damaged fuel gauge
Diagnostic Aids: See the diagnostic aids for DTC P0460. Application Key On Engine Off Key On Engine Running Continuous Memory Ranger GO to Pinpoint Test HX . All others Refer to the Workshop Manual Section 413-01, Instrument Cluster for fuel level indicator diagnosis.
You start by taking to Dealer or someother qualified repair shop .
Instrument Cluster Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1202 Fuel Sender Circuit Open Instrument Cluster Go To Pinpoint Test B . B1204 Fuel Sender Circuit Short to Ground Instrument Cluster Go To Pinpoint Test B .

Aug 02, 2017 | 2006 Ford Taurus

4 Answers

Instrument panel went dead


Checked Every fuse in the fuse box (no small task).This includes #4 - Power point Instrument Panel, #14 - Day time running lamps (auto lamps doesn't work nor does auto lock), #27 - ignition switch run feed, #35 - Instrument Cluster, #41 - Instrument Cluster, #42 - Delayed Accessory, #45 - Ignition switch run/start feed, #102 - Door locks body security module, #103 - Ignition switch, #110 - Ignition switch, & #116 - Ignition switch. But I also check all other ones as well, they all register OK. AC panel & radio work. Turn signals work. Mileage does not work, trip computer does. So, basically, everything works except auto head-lights, auto locks, and the dash cluster (no MPH, RPM, mileage display, Fuel, Temp, Tran Temp, and Oil Pressure).

Aug 19, 2009 | 2003 Ford Excursion

1 Answer

Cars ingnition keeps resetting even while driving.


sound like body control module.it control your instrument cluster.or your instrument cluster has an short.

May 29, 2009 | 1990 Buick Reatta

1 Answer

1999 Oldsmobile Alero Gauge problem


Could be lose connection on the back of the instrument cluster ,which means you would need to pull it out of the vehicle . Check pin fit to instrument cluster . for the B+ voltage suppy an ground connection's .
You said autozone - Tried to have auto zone diagnose from inside the car, came up with no codes. That's in the PCM - engine computer . There scan tool will not communicate with the instrument cluster ,which is also a computer in it's self. Need a factory scan tool to check instrument cluster.
Speedometer and/or Odometer Inaccurate
Step
Action
Value(s)
Yes
No
Important: A short to ground will cause an open fuse(s). Before performing this diagnostic procedure, inspect the fuse(s) for an open.
1
Did you perform the Instrument Cluster System Check?
--
Go to Step 2
Go to Instrument Cluster System Check
2
Turn the ignition switch to the ON position.
With the scan tool select Instrument Panel Cluster, Special Functions, Instrument Panel Cluster (IPC) gauges.
Perform the Speed Gauge Sweep Test.
Does the speedometer complete a full sweep when commanded?
--
Go to Powertrain On Board Diagnostic (OBD) System Check in Engine Controls
Go to Step 3
3
Replace the instrument cluster. Refer to Instrument Cluster Replacement .
Did you complete the repair?
--
Go to Instrument Cluster System Check
--
With a scan tool select the instrument panel cluster, data display, gear status.
Monitor the gear range status.
Move the gear lever through each gear.
Does the scan tool display the correct gear selected?
Your best bet , take it to a qualified repair shop .

Feb 27, 2017 | 2001 Oldsmobile Alero

Not finding what you are looking for?
Cars & Trucks Logo

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...