Question about 1999 Isuzu Rodeo

Open Question

How to disconnect 1998 isuzu rodeo horn - 1999 Isuzu Rodeo

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: timing settings for a 1998 isuzu rodeo

You didn't say whether you had a V6 engine or a 4cyl. Here is the procedure for a V6.

It sounds like he moved the cam shaft independently of the crankshaft or other camshaft so you will need to do all these procedures:

1. Turn the crankshaft until the mark on the spocket is lined up with the mark on the oil pump housing (the mark is on the driver's side at 90 degrees to the sprocket itself).

2. Back off the crankshaft counterclockwise 1/8 turn to ensure the pistons aren't at top dead center. This gives the valves room to move without hitting the piston.

3. Turn the passenger's side camshaft until it "jumps" into place with the alignment mark on the camshaft pully is pretty close to being lined up with the mark on the engine head.

4. Turn the driver's side camshaft until it "jumps" into place but this won't be perfectly lined up with the mark but will be about an 1/8 turn off from the mark. Then line it up by hand.

5. The idler pulleys and tensioner pulleys should be installed on the engine but the tenioner pulley adjuster (it is a little cylinder with a rod coming out of it that is held in place by 2 bolts) should be removed.

6. Place the new belt on the crankshaft first. Be sure the arrows on the belt point in a clockwise direction. If you have a belt with lines and dots then the lines will line up with all markings that you have lined up together. The dots should line up at the 270 degree point on the crankshaft (opposite of the lines and the markings).

7. Loop the belt around the tensioner pulley, around the passenger's side cam, under the waterpump, around the driver's side cam, and finally around the idler pulley. Check all alignments.

8. Put the tesioner adjuster in a vise and squeeze it together until you can place a small drill bit or allen wrench through the holes to keep it compressed.

9. This is the tricky part. You will need to install the tensioner adjuster and that will require some moving of the belt to allow enough play to get the adjuster in place. This may move the passenger's side alignment. If so, you will need to try it again. I find that if you move passenger's side alignment mark clockwise by one tooth of the sprocket, then when you go to put the tensioner in place it lines up. You may find other tricks to overcome this challenge.

10. Once you think you have everything lined up. Use a wrench to turn the crankshaft sprocket 2 full turns. Listen closely and feel for any hard resistance as you do this to determine if the pistons are hitting the valves. If you believe they are hitting each other thenrepeat the adjustment procedure. Not doing this can ruin the valves or more.

11. If everything seems OK. remove the drill bit or allen wrench from the tension adjuster. Perform step 10 again for one final check.

I hope this helps.

Posted on Feb 22, 2009

Ad
  • 15 Answers

SOURCE: 1998 isuzu rodeo thermostat location

0eafb73.gif
Hope this will help...

Posted on May 07, 2009

  • 22 Answers

SOURCE: replacing the power steering pump on a 1998 isuzu rodeo

Remove low pressure and high pressure hoses (this one could be hard to break loose). You might want to have an oil pan handy, to capture the oil. Disconnect electrical sensor. Remove the bolt that holds belt tension adjustment plate. And finally remove the bolt that holds the pump in place. It is bolted from the back and located at the right lower corner of the pump if you are facing the front of the car. Remove the pump assy. I could not remove belt pulley at home, no matter how hard I tried. Ended up taking it to an automotive shop and they removed it in no time, using one of those "pneumatic impact guns". Assemble new pump. Fill the reservoir with PS oil. Make sure both of the front wheels are off the ground, start the engine and slowly spin the steering wheel back and forth for about 5 minutes or untill screeching sound stops and the liquid in the reservoir stops foaming. That will bleed any air that is in the system. Don't go all the way to the end of stroke. Good luck.

Posted on May 09, 2009

  • 715 Answers

SOURCE: where do I put the transmission fluid in my 1998

look for transmission dipstick under hood near firewall remove dipstick and put fluid in hole where dipstick came out of

Posted on Nov 09, 2009

  • 10865 Answers

SOURCE: What kind of transmission fluid do you put in a

hello. I recommend Mobil 1 transmission Fluid. Since you do not have a dip stick on this model, Isuzu recommends that you let the service center do this work but; YES you can do it!! Be careful not to overfill but do as follows to check the fluid. As you don?t have an ATF dipstick, you will have two plugs facing down on the trans pan. The plug higher up on the pan is the fill/level check (stamped/recessed into the rear right corner of pan). ATF should just drip from this plug on a hot, idling truck, in neutral on a flat surface. The lower one is the drain. The one at the back of the pan in a recess is the filler. You need a squirt pump or something like one to fill it with the engine running.

Posted on Mar 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does the starter relay fuse for a 1998 Isuzu rodeo look like and where is is located in the fuse box


Crystal, this is what I found on the Rodeo starter fuse/relay.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
99 Isuzu Rodeo LS Underhood Fuse Box Diagram Circuit Wiring Diagrams
1997 Isuzu Rodeo Question Fuse Box Diagram Electrical Problem
1999 Isuzu Rodeo Main Fuse Box Diagram Circuit Wiring Diagrams
1998 Trooper Relay Solenoid Starter 1998 Isuzu Trooper All of

Jul 06, 2016 | Isuzu Cars & Trucks

1 Answer

Horn wont work when I put new horn on


Hi

Either

Poor earth connection to the horn or to/from the horn switch.

The horn switch has failed, loose wires or metal strip dislodged, wires can come free on steering wheel centre horns. finally the fuse for the horn, often is a shared fuse with the radio or dashlights

Regards

Dan

Dec 31, 2010 | 1998 Isuzu Rodeo

1 Answer

Where in the fuse box for a 2000 isuzu rodeo is the horn fuse. It's not posted in manual. Thanks


horn don t work fuse is good and looking for wiring diag. to replace horn button in stiring wheel

May 06, 2010 | 2000 Isuzu Rodeo

1 Answer

Horn problem on 01 rodeo


It is the horn relay. It the horn is not working either the wiring is disconnected or corroded or the horn is bad.

Nov 12, 2009 | 2001 Isuzu Rodeo

1 Answer

The horn want stop blowing so i have to thak the


could have stuck horn switch in steering wheel..or maybe the horn has internal short.

Sep 29, 2009 | 1998 Isuzu Rodeo

1 Answer

Engine will not shut of until i disconnect the battery cable


The most likely cause of this problem can be traced to the key switch itself. I highly recommend you have the key switch either tested or replaced. It sounds as if the circuit is not getting cut when the key is turned off. I hope this helps and please do not forget to rate me.

May 21, 2009 | 1998 Isuzu Rodeo

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14378 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...