Question about 1999 Dodge Durango

1 Answer

No bus sign blinking in odometer - 1999 Dodge Durango

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Replace pcm.

Posted on Jan 05, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Got a 2003 dodge neon its not doing any thing and say no bus how can I fix this


That no bus error means there is a problem with the serial data network , your best bet is to take to the dealer or an ASE certified repair shop. Or you can google no bus message an see what you come up with , an check it out on youtube also. Why does your Dodge Ram odometer say no bus

Nov 20, 2015 | Dodge Cars & Trucks

1 Answer

What does no bus mean on the odometer


No bus means the bus is not operating properly. It means no communication between the modules inside your jeep. All modules inside the jeep (A/C control, radio, onboard computer or trip computer, body control, etc) communicate with each other by means of a wire called bus. Check that wire.

Jun 24, 2014 | 2001 Jeep Grand Cherokee

1 Answer

Dakota - 2001, started, died and won't start. all dash indicators light as normal except odometer says "No Bus."


Hi, if odometer say no bus you are loosing your bus signal some were ,with out a bus signal the car not going to run the bus signal runs to every module on your truck. This could be as easy as a blow en fuse to a wire shorted out or a bad module . Depends on your know how around cars . If your not sure you should take to local shop or dealer. If i can help you further just re post.
Thanks dodge tec

Jan 02, 2011 | 2001 Dodge Dakota

1 Answer

Odometer reads no bus


check bulkhead connecter for corrosion, cluster is your body controll module, losing signal to fuel pump module , and pcm, thios is a communication issue, volt meter wil help, back probe diagnostic connecter, pin 7, white wire, to see if signal is there, GOOD LUCK RDJRP

Jul 16, 2009 | 1999 Dodge Ram

2 Answers

No Bus Error


All the modules are connected together to communicate with each other via the PCI bus. It is possible that one of the modules is pulling the bus down.Since the vehicle won't start it could be any one of the modules. It will be a process of elimination to find the faulty one by disconnecting them one at a time. Here are a few, powertrain control module (the one you replaced) Instrument cluster, overhead console, anti-lock brakes, airbag. Since the cluster unplugged wont read anymore, just try to start the vehicle to see if that was the one. Otherwise see if the odometer message of "no bus" goes away after each one is unplugged.

Apr 23, 2009 | 1999 Dodge Durango

1 Answer

Need to disconnect odometer 2003 Chevy impala


good luck buddy, but is no way to diconnect the odometer.. the reson for this is its illegal to disconnect the odometer, because most car lots would do this.. take a bus man..lol.. good luck keith...

Mar 20, 2009 | 2003 Chevrolet Impala

2 Answers

Wont start my odometer blinks and says no bus


From the official Durango shop manual......(abbreviated)

Self Diagnosis Test

Vehicle key position is OFF ,or able to pull key out.
Hold in the trip odometer button (dont release yet)
Turn key to the ON position (one notch), but DON'T try to start the engine
Continue holding the trip button for about 10-12 seconds until CHEC appears in the odometer display
Release the trip button.
Series of three digit numeric failure codes may appear.
If no failure message appears, the self diagnostic test will proceed as described in step 6


Code Chart

110- cluster CPU,RAM,EEPROm failure, replace cluster

900-CCD data bus not operational, check CCD data bus connections at cluster, check the cluster fuses,check the CCD data bus bias, cehck the CCD data bus voltage, check the CCD data bus terminations.

920-cluster is not recieving a vehicle speed message from the PCM, check PCM software level and reflash if required, use the ($2500+) DRBIII scan tool to verify the vehicle speed message is being sent by the PCM

921-the cluster is not recieveing a distance pulse message from PCM,check PCM software level and reflash if required, use the ($2500+) DRBIII scan tool to verify the distance pulse message is being sent by the PCM

940-the cluster is not recieving an airbag lamp-on message from the ACM, check the CCD data bus connections at the ACM, check the ACM fuse.

950-cluster not recieving an ABS lamp-on message from the CAB, check CCD data bus connections at the ACM, check the ACM fuse.

960- clsuter not recieving a PRND21 message from the TCM, check the CCD data bus connections at the TCM, check the TCM fuse.

999-An error has been discovered, record the failure message, depress the trip odometer reset button to continue the Self-Diagnostic Test

Step 6
Instrument cluster will test each segment of the odometer (all first, then each one seperately)

Step 7
Bulb test

Step 8
Gauge test

Step 9
test completed

The instrument cluster will return to normal operation at the completion of test, if ignition switch turned off, or a vehicle speed message indicating movement recieved from the PCM on the CCD data bus.

Hope that help you or anyone else in future.

Aug 10, 2008 | 2000 Dodge Durango

1 Answer

No BUS on odometer


I used to have the NoBUS show up on the odometer also, but always while driving. The immediate fix was a sharp rap on the top of the cluster with my fist. To fix it permanently, I removed the cluster,cleaned the contacts both cluster and harness with spray contact cleaner, then applied some dielectric grease to prevent any further corrosion.

HTH

Jun 22, 2008 | 1999 Jeep Wrangler

Not finding what you are looking for?
1999 Dodge Durango Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...