Question about GMC C1500

Open Question

How to change a neutral safety switch on a 1995 gmc 2wd 1500 automatic

How to change neutral safety switch

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 91 Answers

SOURCE: neutral safety switch....I think

The switch is located at the top of the clutch pedal assembly, above your feet. Its a little cramped, but its a simple dc two wire switch, you should be able to check it with a meter for power and to see if the switch does indeed need replacement. If thats the problem, when you see the new switch, you'll know it goes in, very easy. good luck

Posted on Aug 12, 2008

emissionwiz
  • 75822 Answers

SOURCE: 1995 pontiac grand prix se neutral safley switch

this is part of the gear position switch on top of the trans where the shift linkage connects, it is mounted over the selector post that sticks out of the trans. Here is a picture.
300? 300: true ); MAX-HEIGHT: 400px; ; HEIGHT: expression(this.height > 400? 400: true )" src="http://info.rockauto.com/getimage/getimage.php?imagekey=96388&imageurl=http%3A//info.rockauto.com/ACDelco/12450003.jpg" />

Posted on Feb 13, 2009

c17hydro
  • 2984 Answers

SOURCE: replace the neutral safety switch on my 1999 Chevy Silverado

If it looks like this:





It is mounted on the side of the tranny. It also says a special to remove it.991cb34.jpg

Posted on Apr 01, 2009

ZJLimited
  • 17970 Answers

SOURCE: Looking for the neutral safety switch

Neutral Safety/Back-up Light Switch

This is a combination switch which controls both Neutral Safety and Back-up lamp circuits.

C6 Transmission


8290dff.jpg

C6 neutral start switch

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Remove the downshift linkage rod return spring at the low-reverse servo cover.
  4. Coat the outer lever attaching nut with penetrating oil. Remove the nut and lever.
  5. Remove the 2 switch attaching bolts, disconnect the wiring at the connectors and remove the switch.
  6. Installation is the reverse of removal. Adjust the switch and tighten the bolts to 55-75 inch lbs. (6.2-8.5 Nm).
  7. Remove the jackstands and lower the vehicle.
  8. Connect the negative battery cable.
AOD Transmission

e7f4231.jpg

Removing the AOD neutral start switch
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disconnect the wiring from the switch.
  4. Using a deep socket, unscrew the switch.
  5. Installation is the reverse of removal. Tighten the switch to 10 ft. lbs. (14 Nm).
  6. Remove the jackstands and lower the vehicle.
  7. Connect the negative battery cable.
4R70W Transmission

2f68dfc.jpg


Removing the Manual Lever Position (MLP) sensor

As of 1994, the neutral safety switch is referred to as a Manual Lever Position Sensor (MLP).
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disengage the harness connector from the MLP sensor.
  4. Remove the 2 sensor attaching bolts and remove the sensor.
To install:
  1. Install the MLP sensor and install retaining bolts. Do not tighten, the sensor requires adjustment.
  2. Adjust the MLP sensor then tighten attaching screws to 80-100 inch lbs. (9-11 Nm).
  3. Remove the jackstands and lower the vehicle.
  4. Connect the negative battery cable.


ADJUSTMENT

C6 Transmission
  1. Hold the steering column transmission selector lever against the Neutral stop.
  2. Move the sliding block assembly on the neutral switch to the Neutral position and insert a 0.091 in. (2.3mm) gauge pin in the alignment hole on the terminal side of the switch.
  3. Move the switch assembly housing so that the sliding block contacts the actuating pin lever. Secure the switch to the outer tube of the steering column and remove the gauge pin.
  4. Check the operation of the switch. The engine should only start in Neutral and Park .

4R70W Transmission


4cc4151.jpg


Adjusting the MLP sensor

Park is the last detent when the manual control lever is full forward. Return 2 detents toward the output shaft for Neutral.
  1. Position the manual control lever in Neutral .
  2. Insert Gear Position Sensor Adjuster tool T93P-700 10-A or equivalent, into the slots.
  3. Align all 3 slots on the MLP sensor with 3 tabs on the tool.
  4. Tighten the attaching screws to 80-100 inch lbs. (9-11 Nm).

I hope help you. Good luck (rated this help).

Posted on Sep 18, 2009

jmgldsmth
  • 1869 Answers

SOURCE: where is the neutral safety

the neutral safety switch is located on the side of the transmission where the shift lever connects to the transmission

Posted on Jul 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why do I have reverse gear but no reverse lights? Light worked recently, and not bad bulbs or anything, what could it be? I have a 1996 gmc jimmy sls 2wd automatic. Thank you


Does you shift indicator point to "R" when in reverse. The reverse light are switched on by the selector shaft position sensor built into the Parp/Neutral Safety Switch. It may be bad or just out of adjustment.

Mar 29, 2015 | GMC Cars & Trucks

1 Answer

Will not start..I changed the neutral safety switch


switch may need to be adjusted by loosening the bolts on the mounting plate it is adjustable up or down.....check brake safty switch on pedal up under dash

Oct 30, 2013 | 2008 Chevrolet Silverado 1500 2WD

1 Answer

Neutral safety switch


most gm nuet safety is yellow and purple .....out of ignition switch is a big yellow wire that is crank out and input to nuet saf switch......out of nuet switch is color purple that goes strieght to start selenoid.....purple wire also goes to the crank fuse 5amp.. in the fuse box under dash... this fuse goes to the pcm main computer.. same for auto and clutch

Sep 04, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

1 Answer

Cannot find starter/solinoid on 95GMC Sonoma 2.2L 2wd


easy to find follow the red wire to under the engine it bolts right to it

Jun 17, 2009 | 1995 GMC Sonoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...