Question about 2004 Chrysler Sebring Convertible

Open Question

04 chrysler sebring convertible's windows wont roll down

My 04 chrysler sebring convertible's windows wont roll down. we have checked all fuses and they all seem to be fine. what else could the problem be?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: replace air filter 2002 Chrysler Sebring convertible

you need to loosen the clamp on the throttle body and unplug the map sensor then there are two clips on the other end pull that out and you should be able to pull the filter out you don't need to take the box off.

Posted on Apr 28, 2009

motor1258
  • 6674 Answers

SOURCE: power windows don't work!

Check under hood for fuse/relay center or box & map should be on underside of cover. Usually on drivers side.

Posted on May 18, 2009

  • 166 Answers

SOURCE: Power Windows won't work

Fuse is good you say? There are four may possible causes listed in this diagnostic article:

http://yourhandymanzone.com/Your_Handyman_Zone_How_To_Pages_Vehicle_Car_Zone_Cars_Trucks_Vans_Windshield_Windows_Window_Does_Not_Roll_Up_Down.htm

Good luck!
Brad

Posted on May 25, 2009

  • 396 Answers

SOURCE: Driver-side window non-respondent (2003 4door Chrysler Sebring)

Your widow regulator is defective or the motor is defective. Remove door panel, using a punch, punch out the rivets, using a !/4 drill out the aluuminum plugs. Remove the regulator and inspect, if its not defective apply bearing grease when mechanism rolls up and down. Rivets must be replaced by 1/4 screws and nuts. Take motor apart, you will find three plastic plugs which have a tendency to disenegrate, replace these with ball bearings, pack the motor and I do mean pack it with wheel bearing grease. Reasemble.

Posted on Jun 29, 2009

  • 4088 Answers

SOURCE: My 2004 chrysler sebring electical is not working.

Check around the MAP sensor area for any connections that may have been disturbed while you were replacing the sensor. Most or all of those functions are controlled by the body control module. I would think that a fault like that would show on the scanner readouts.

Posted on Aug 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

04 chrysler Sebring coupe won't crank unless I hold gas


engine wont turn over unless you hold gas pedal down? That is an electronic issue. you should have a ENGINE LIGHT ON....have the code read.

Aug 23, 2014 | 2004 Chrysler Sebring

1 Answer

When i open the top on my 1996 chrysler sebring convertible i notice that the front windows go down but the rear windows don't. is this normal or do they have a reset so they could go down a bit.


I had the same car,when we put the top down we had to hold the botton for the top in the down posistion until the back windows were down.

Nov 15, 2012 | Cars & Trucks

1 Answer

2005 Sebring sputter and died won't turn on


sounds like an electrical prob. check for corroded battery cables

Sep 05, 2012 | 2005 Chrysler Sebring Sedan

1 Answer

Passenger window wont roll up.......fuse/relay is good....window motor is good..module is good.......tested and got a ul 1110 and ul 1120 codes ...what is this ? 2008 sebring convertible / chrysler


IF THE PASSENGER WINDOW SWITCH IS BAD IT WONT WORK FROM EITHER SIDE HAS TO BE A COMPLETE CIRCUIT.IF YOU MANUALLY JUMPED WINDOW MOTOR WITH A BATTERY AND TWO WIRES ,I WOULD START THEIR.OR IF THE DRIVER WINDOW SWITCH IS BAD SAME THING

Aug 03, 2011 | 2008 Chrysler Sebring Convertible

1 Answer

My 04 sebring convertible running great check engine light started flashing, engine died and coasted to a stop with sufficient battery will not turn over


Sounds like PCM (powertrain control module) "the computer". There's one for the trans and one for the engine. Call a part store for availability... auto dismantlers... my guess between $200 & $500.

Feb 27, 2011 | 2004 Chrysler Sebring

2 Answers

Driver-side window non-respondent (2003 4door Chrysler Sebring)


you need to check your window switch also check the fuse box for blown fuse

Jun 29, 2009 | 2003 Chrysler Sebring

1 Answer

Power windows don't work!


Check under hood for fuse/relay center or box & map should be on underside of cover. Usually on drivers side.

May 18, 2009 | 2004 Chrysler Sebring

1 Answer

Fuse keeps blowing out


rol down window instead! ok kidding, does fan alone work ok? it might be your clutch shorted drwaing too many amps. its wheat engages your compressor when you turn on ac.

Mar 30, 2009 | 1997 Chrysler Sebring

Not finding what you are looking for?
2004 Chrysler Sebring Convertible Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...